Heat Shrink Tubing and Sleeves for Harness Protection Heat shrink is chosen by recovered diameter, not by the size printed on the reel, and that is where most harness drawings go wrong. The 2:1 tubing here runs from 1.17 mm to 50.8 mm expanded, with recovered diameters down to half of that and walls from 0.41 mm to 1.14 mm. The 3:1 adhesive lined tubing runs from 3.18 mm to 38.1 mm expanded, with a meltable inner wall that seals the joint as it shrinks. Expanded diameter, recovered diameter, recovered wall and minimum shrink temperature are given per size.
Threaded Inserts and Standoff Nuts for Plastic Enclosures A thread in a plastic boss strips after a few assembly cycles, so the thread is put into a brass insert instead of into the moulding. The heat set inserts here run from M2 at 3.2 mm outside diameter to M6 at 8.2 mm, with lengths from 3.0 mm to 9.5 mm and hole sizes from 3.0 mm to 8.0 mm. The self-clinching nuts cover M2 to M6 for the metal bracket or chassis that the plastic case is fixed to. Hole size, insert length, recommended boss diameter and minimum sheet thickness are given per part, because the boss is what fails first.
Nylon Grommets and Hole Plugs for Panel Openings A raw hole in a panel cuts cable, and an open hole in a panel passes dust, so both ends of the problem are solved with one moulded nylon part. The bushings here cover 6.4 mm to 22.2 mm holes with inside diameters from 3.2 mm to 15.9 mm, for panels up to 3.2 mm thick. The dome plugs cover 4.7 mm to 50.8 mm holes, with a head thickness of about 1.6 mm and locking fingers that take panels up to 6.4 mm. Hole diameter, inside diameter and maximum panel thickness are given per part, because those three figures decide whether the part fits at all.
Mounting Brackets and DIN Rail Clips for Enclosures An end bracket is the part that stops a bank of terminals from sliding, and its width is what sets the pitch of the whole row. The brackets here are 5.2 mm, 8 mm and 9.5 mm wide, for NS 35/7.5 and NS 35/15 rail, in PA or Wemid from HB to V0. Depth on rail runs from 33.5 mm on the 9.5 mm bracket to 46.5 mm on the 8 mm Weidmuller part, which is the figure that decides whether the door closes. The rail itself is 35 mm wide steel to EN 60715, perforated on a 25 mm pitch, and rated for a 1.92 kA short-time current for one second.
Grounding Studs and Earth Terminals for Chassis Wiring A chassis bond is only as good as the metal under the lug, so the stud is chosen by panel thickness and by the fault current it has to carry. The studs here run from a self-clinching M6 part in 1.0 mm sheet to a self-piercing M6 part in 2.2 mm aluminium, plus CD weld studs in 1/4-20, M6 and M8. Rail earth terminals cover 0.14 to 4 mm2 in screw connection on NS 35/7.5 and NS 35/15 rail. Hole size, minimum centre distance to the edge, pull-out and torque-out are given per part, because those four figures decide whether the bond holds.
Breather Vents and Pressure Equalization Plugs for Sealed Cases A sealed case is not a stable case: as the inside warms, the pressure rises, the seals are loaded and moist air is drawn in as it cools. The screw in vents here run from an M6 part at 300 ml per minute to an M32 part at 16 litres per minute, which covers a case of 2 litres up to one of 200 litres. Protection runs from IP65 to IP68 at 2 metres for one hour, with IP69K on every part except the smallest, and bodies in polyamide, 316L stainless and polycarbonate. Airflow, torque and through hole diameter are given per part number, because the hole has to be drilled once.
Cable Clamps and Harness Ties for Internal Wiring A harness is only as tidy as its fixing points, and a clamp is chosen by bundle diameter and hole size rather than by the size of the loop. The clamps here run from a 4.8 mm nylon loop to a 25.4 mm wire harness clip, in nylon 6/6 to UL94 V-2 and in zinc plated steel with an elastomer cushion. The ties are PA66 and UV stabilised PA66W, from 100 mm at 80 N to 387 mm at 535 N, with bundle diameters from 22 mm to 100 mm. Hole size, bundle range and tensile rating are given per part, because those three figures decide whether the clamp and the tie work together.
Enclosure Handles and Corner Guards for Portable Units A portable unit is carried by its handle and protected by its corners, and both parts are chosen by load rather than by appearance. The handles here run from a 35 kg surface sprung part in 1.2 mm steel to a 150 kg double sprung recessed part with a 10 mm dish and 14 fixing holes. The corner guards are 2 leg or 3 leg steel parts from 0.8 mm to 2.0 mm thick, with internal radii from 3/8 inch to 1/2 inch and zinc or nickel finish. Load rating, dish depth and fixing hole diameter are given per part, because those three figures decide whether the handle fits the panel.
PCB Card Guides and Board Retainers for Rack Cards A card guide holds a plug in board at both ends so the edge connector does not carry the weight of the card, and it sets the slot pitch in the rack. The snap in nylon guides here take a panel of 1.2 mm to 2.3 mm through a 4.6 mm hole, with card channels for 1.6 mm and 2.4 mm boards. Lengths run from 63.5 mm to 254 mm, and the deep channel version gives a 5.08 mm channel for high shock and vibration. Body materials are nylon 6/6 to UL94 V-2 and glass filled nylon to UL94 V-0, with a grounding clip option.
Fan Guards and Filter Screens for Enclosure Cooling A cooling opening needs two parts: a guard that stops a finger reaching the blades and a filter that stops dust reaching the heat sink. The wire form guards here are C1008 steel with a bright nickel chrome finish, from 40 mm to 120 mm fan size, with mounting hole centres of 32, 50, 71.5, 82.4 and 104.8 mm. The filter assemblies combine a guard, a foam media and a retainer in one part, with media from 30 to 100 pores per inch and a thickness of 4.3 mm to 10.6 mm. Screw pitch is the figure that decides whether a guard fits, because the guard has to line up with the fan holes.
Rubber Bumpers and Feet for Enclosure Support A bumper is a mechanical part with three numbers: the footprint, the height and the hardness. The urethane pads here run from 7.90 mm to 47.75 mm across and from 2.20 mm to 16.76 mm high, at 67 or 72 Shore M. Shapes are cylinder with a flat top for load bearing, hemisphere for a rounded edge, and square for more contact area on a flat base. The adhesive is a natural rubber R30 pressure sensitive layer on most parts, with an acrylic option where the surface is a low energy plastic.
Turret Terminals and Solder Lugs for Panel Wiring A turret terminal is a post a wire is wrapped around and soldered to, and the dash number on the part is the board thickness it is swaged into. The brass posts here are bright tin plated to MIL-T-10727 Type 1, in single, double and triple turret styles, with heights above the board from 2.36 mm to 7.65 mm. Mounting holes run from 1.70 mm to 2.39 mm, and the flange is 3.18 mm across on the swage mount bodies. The solder lugs on the same page are lockwasher lugs for a #4 or a #8 stud, in 0.018 inch brass with a matte tin finish.
D-Sub Connectors for Serial and Instrument Ports A D-Sub is chosen by shell size, not by pin count alone: 9 positions is shell DE, 15 is DA, 25 is DB, 37 is DC and 50 is DD. The solder cup parts here are rated 5 A per contact at 250 V AC working, with 500 V AC for one minute, 15 mOhm contact resistance and a range of -50 to +100 C. The board mount part is a 9 position right angle plug on a 2.74 mm centreline, with board locks, a ground strap and grounding indents. Contacts take 20 to 28 AWG wire on the solder cup bodies.
Card Edge Connectors for Backplanes and Riser Cards A card edge connector is the cheapest way to make a board removable, because the gold fingers on the board are the plug and there is no mating half on the loom. The 3.96 mm family here takes a 1.57 mm card, carries 5 A per contact and holds 1800 V AC rms between contacts. The 1.27 mm high density family uses a hairpin bellows contact rated 1 A, with 150 g of normal force and a card window of 1.57 mm plus or minus 0.20 mm. Both are through hole parts, and the choice between them is set by the finger pitch already on the board.
DIP and SIP IC Sockets for Through Hole Packages A socket is chosen on three things: the package it takes, the number of times the part will be changed, and the heat the board sees. The stamped open frame DIP sockets here run from 8 to 40 positions on a 2.54 mm pitch, in 7.62 mm and 15.24 mm row spacing, with tin plated phosphor bronze contacts. The machined sockets and strips carry a beryllium copper four finger contact rated 3 A, with 10 mOhm contact resistance and 1,000 insertion cycles. Tail length runs from 3.15 mm to 3.18 mm, which covers boards from 1.0 mm to 1.6 mm.
Cable Glands and Strain Relief Bushings for Enclosure Entries A cable entry is decided by three numbers: the thread or the punched hole, the cable outer diameter, and the wall thickness. The metal glands here are nickel plated brass with a polyamide V0 insert and an NBR seal, rated IP68 at 10 bar for 30 minutes and IP69K, with a NEMA 4, 4X and 6 type rating and a range of -40 to +100 C. They run from M12 to M32, with two clamping ranges on the same thread, and a torque figure from 4 Nm to 15 Nm. The nylon bushings snap into a 14.3 mm to 19.0 mm punched hole and take a 1.6 mm or a 3.2 mm panel.
SIM and Memory Card Holders for Field Accessible Storage A card holder is the one connector a customer opens in the field, so retention and the detection switch matter as much as the contact count.\\nThe SIM parts here use 6 contacts on the ISO 7816 and GSM 11.11 layout, with a hinged lid or a push-push slot, rated 5,000 cycles.\\nThe microSD parts use 8 contacts on a 1.10 mm pitch, with heights of 1.42 mm, 1.68 mm and 1.83 mm above the board.\\nAll of the microSD parts carry a card detection switch and are rated 10,000 cycles at 0.5 A.
Light Pipes and LED Holders for Front Panel Indicators A light pipe moves the light from a board LED to the front panel, so the LED can sit away from the surface and the panel stays closed.\\nThe panel parts here take lenses of 3 mm or 5 mm, press fit into a 2.92 mm or a 3.96 mm hole, for panels from 1.19 mm to 2.36 mm thick.\\nBody lengths run from 2.5 mm to 30.5 mm, which is the range that covers most board to panel gaps.\\nThe LED holders are moulded nylon, in right angle bodies for 3 mm and 5 mm lamps and in panel clips for a 5 mm indicator.
USB Type-C and USB A Receptacles for Power and Data Ports A USB port is decided by three numbers: the tab length against the board thickness, the current rating against the cable, and the mating cycles against how often the port is used.\\nThe Type-C parts here carry 24 contacts on a 0.5 mm pitch, rated 5 A at 48 V DC and 10,000 mating cycles.\\nThe Type-A parts carry 4 contacts on a 2 mm pitch, rated 1 A or 1.5 A per contact and 1,500 mating cycles.\\nSolder tab length runs from 0.60 mm to 1.30 mm, and that range covers boards from 0.80 mm to 1.60 mm.
Banana Jacks and Binding Posts for Test and Bench Panels A banana jack is a 4 mm socket with a solder tag, and a binding post is the same socket with a nut that also takes a wire or a spade lug.\nThe panel parts here are rated 15 A with a 2500 VDC hands free limit, for panels from 1.6 mm to 9.5 mm thick.\nBodies are brass with tin or gold plating, insulators are polycarbonate or PPS, and the high temperature version runs to 220 C.\nNon insulated swage mount jacks are listed for a board that needs a test point at 15 A.
DIN and Circular Connectors for Panel Wiring A rack card and a panel box need two different connectors, and both have to survive a harness that was made somewhere else.\nThe DIN 41612 parts here run 32, 64 and 96 ways at 2 A per contact on a 2.54 mm pitch, in rows a, b and c, straight or right angle.\nThe M12 parts are 4 position A and D coded panel feed throughs, rated 4 A at 250 V and sealed to IP67 to IEC 61076-2-101.\nEvery row states the termination length and the coding, because those two decide whether the mating half fits.
Standoffs Spacers and Mounting Hardware for Board Stacks A standoff sets the distance between two boards, and it is the part that decides whether a connector still mates after the screws are tight.\nThe parts here cover M3 threads in brass and zinc plated steel, from 5 mm to 50 mm, in male to female and female to female bodies.\nHex bodies are 5.5 mm across flats, and the round nylon spacers run from 2 mm to 30 mm with inner diameters of 2.2 to 5.2 mm.\nThe snap clip spacer studs hold a board on a 2.1 mm panel without a nut on the far side.
IR Receiver Modules for Remote Control and Data An IR receiver module is a photodiode, a band pass filter and a demodulator in one three pin package, and it outputs a clean logic pulse.\nThe 38 kHz parts here run from 2.5 to 5.5 V, draw about 0.35 mA, and reach 24 m with a 50 mA emitter on the axis.\nHalf transmission angle is plus or minus 45 degrees, and the package is 5.0 x 6.95 x 4.8 mm on the minicast parts.\nAGC2 and AGC4 versions are both listed, because the choice decides which remote codes are accepted in daylight and under lamps.
Seven Segment LED Displays for Instrument Readouts A seven segment display is chosen on digit height, common pin and colour, and then on whether the driver can supply the current.\nThe 14.22 mm parts here give 3,600 to 8,000 ucd at 10 mA in high efficiency red, and 14,000 to 34,000 ucd in super bright red.\nForward voltage is 1.9 V typical at 10 mA, with a 30 mA DC and 160 mA pulsed limit on the standard red part.\nCommon anode and common cathode versions share the same 10 pin package and the same 2.54 mm pin row.
Fuse Holders and Clips for Board Level Protection A fuse holder is the part that decides whether a fuse protects the board or only looks as if it does.\nThe 5 x 20 mm holders here run from 6.3 A at 250 VAC on a snap-in body to 15 A at 500 VAC on a panel part with LCP insulation.\nSMT and THR versions are listed for boards that are reflowed, with a 260 C reflow rating and a matching cover.\nEvery row states the fuse size, the rating and the mounting, because those three have to match the fuse that is fitted.
Jumper Links and Shunt Headers for Board Configuration A jumper link is the cheapest way to make one board serve two builds, and the cheapest way to lose a contact if the wrong shunt is used.\nThe 2.54 mm shunts here carry 3 A at 250 VAC with 20 mOhm maximum contact resistance and a 25 mating cycle rating.\nOpen top, grip and test point versions are listed, in heights of 5.97 mm and 13.75 mm, from 2 to 16 positions.\nThe Samtec shunt in the same table is rated 4.3 A per contact, for boards that draw more than the standard part allows.
DIP Switches and Rotary Address Switches for Configuration A DIP switch sets an address, a mode or a bus termination once, and then has to hold that setting for the life of the product.\nThe slide types here run from 2 to 12 positions in SPST, 100 mA at 20 VDC, gold contacts and 2,000 cycles of actuation life.\nThe rotary types give 10 or 16 positions in real or complementary code, in a 7.2 mm square body only 3.0 mm high.\nEvery row states the terminal style, the actuator and the packing, because those three decide whether the part fits the line.
Rocker and Toggle Switches for Equipment Panels A panel switch is chosen on the load it breaks and on the cutout already punched in the panel, not on the look of the actuator. Toggle parts on this page run 5 A at 120 V AC on a 6.35 mm round bushing, while snap-in rockers reach 15 A at 125 V AC on a 19.4 x 13 mm cutout. Mains rockers add 128 A inrush for a capacitive supply and a 3 mm contact gap. Every row lists circuit, contact rating, mounting and termination.
Wire to Board Crimp Housings and Headers for Harness Builds A wire to board connector is picked on pitch, current and the wire the harness actually uses, and the housing and terminal must come from one series. This page runs from 1.25 mm PicoBlade at 1 A to 4.20 mm Mini-Fit Jr at 9 A, with JST XH at 3 A and Molex Micro-Fit 3.0 at 8.5 A per contact in between. Wire ranges, insulation diameter, contact resistance and mating height are listed per part number. Headers, housings and crimp terminals are quoted as matched sets.
EMI Shielding Cans and Contact Gaskets for RF Boards A board level shield is chosen on the opening it has to close and on the height left above the tallest part, not on wall thickness. One piece drawn cans on this page run from 10.2 x 6 x 3 mm to 32.3 x 23.8 x 3.7 mm in tin plated steel and in nickel silver. Two piece versions add a solderable frame so the cover comes off for rework, and the gasket table gives free height, working height and surface resistance. Contact fingers run from 1.5 mm to 6 mm, with conductive foam, elastomer and woven mesh for enclosure joints.
Pin Headers and Female Sockets for 2.54 mm Board Stacking A 2.54 mm header is chosen on the number of ways, the mating length and the plating, because the pitch is fixed by the standard. The male strips on this page carry 3 to 6.3 A and run at 250 to 550 V depending on the maker and the way count. Female sockets add the mating half for board stacking, in Tiger Buy contact form with a square tail. Tin and gold plating are both listed, since the finish decides the insertion life and the cost.
Test Points and Spring Contacts for Board Probing A test point is chosen on the probe that will touch it and the hole it fits, not on the colour of the base. The loop parts on this page take a 1.0 mm or 1.6 mm board hole and stand 4.6 to 8.9 mm above the board. Colour keyed bases identify a node at a glance, and the same body is stocked in five colours. Spring loaded pins add a 2 A contact with a defined working height for a bed of nails fixture.
Audio Jacks and DC Power Connectors for Instrument Panels A panel jack is chosen on the plug it must accept, the current it must carry and the number of insertions it will see. The 3.5 mm parts on this page carry 1 A at 12 V and run 5,000 cycles, in horizontal through hole form. DC jacks cover a 1.3 mm and a 2.0 mm centre pin, at 2.0 and 2.5 A, with and without a switch contact. Barrel and plug diameters are stated, because 2.0 mm and 2.5 mm plugs do not interchange.
Panel Potentiometers and Control Knobs for Front Panel Adjustment A panel control is chosen on shaft, mounting and life, because the value is the easy part and the mechanics decide whether it lasts. The 9 mm parts on this page turn 280 degrees and run 5,000 to 10,000 cycles at 0.05 W. A 12 mm body adds a longer 20 mm flatted shaft for a taller front panel. Knobs are listed with the shaft diameter and the number of turns the dial reads.
EMI Feedthrough Filters and Filter Connectors for Shielding A feedthrough filter removes noise at the point where a wire crosses a shield, which is the only place the return path is still short. Chip three terminal parts on this page cover 0.1 to 2.2 uF at 2 to 4 A in 0603 and 0805. Threaded filters cover 500 pF to 10 nF at 10 to 20 A, with the thread and voltage stated per part. Capacitance alone does not decide the part; the current rating and the thread decide whether it can be fitted.
Photointerrupters and Optical Switches for Position Detection A photointerrupter is chosen on slot width, aperture and output type, because those three set the resolution and the circuit around it. Transmissive parts on this page run from a 2 mm slot in a 5.2 mm tall body to a 5 mm slot 12 mm deep. Reflective parts sense a target at about 3 mm and suit paper, label and flag detection. All of them need a defined aperture or a comparator, and the page states which parts include one.
Battery Holders and Coin Cell Retainers for Backup Power A backup cell holder is chosen on cell size, mounting side and whether the cell has to be replaced in the field. Through hole retainers on this page cover 12 to 23 mm coin cells, and surface mount parts cover 12 and 20 mm. Cylindrical holders add AA and 18650 cells with polarised contacts and snap in retention for wave soldering. Contact material and plating are listed per part, because that is what sets contact resistance over life.
Heat Sinks and Thermal Interface Pads for Power Boards A heat sink is chosen on thermal resistance at the airflow the board actually sees, not on the footprint that looks neat. The extruded parts on this page run from 13.4 to 23.4 C/W in still air and fall to about 5 to 7 C/W at 200 LFM. Between device and metal, a pad replaces grease where the gap has to be filled or the joint has to be reworkable. Pads here run from a 0.229 mm glass reinforced insulator to 4.5 W/mK soft gap fillers up to 8 mm thick.
Reed Switches and Magnetic Actuators for Position Sensing A reed switch is chosen on sensitivity, load and body length, because those three decide the operate distance and the life of the contact. The parts here switch 5 to 20 W at 140 to 200 V DC, with sensitivity bands from 6 to 38 AT. Glass and surface mount versions share the same contact ratings, and the actuator has to be matched to the switch. Each row lists contact form, rating, sensitivity band and body size.
Trimmer Potentiometers for Calibration and Bias Setting A trimmer is picked on turns, power rating and sealing, because the electrical load is small and the setting has to survive wash and life. The parts here run from a single turn 3/8 inch body to a 25 turn lead screw type, at 0.25 W to 0.75 W. Power derates to zero at the top of the temperature range on every series, so the rating at 70 C is the figure that matters. Each row lists turns, power, temperature coefficient and mounting.