Contact Us
  • Home
  • COMPONENTS
  • Test Points and Spring Contacts for Board Probing

Test Points and Spring Contacts for Board Probing

A test point is chosen on the probe that will touch it and the hole it fits, not on the colour of the base. The loop parts on this page take a 1.0 mm or 1.6 mm board hole and stand 4.6 to 8.9 mm above the board. Colour keyed bases identify a node at a glance, and the same body is stocked in five colours. Spring loaded pins add a 2 A contact with a defined working height for a bed of nails fixture.
quote now

Product Specifications

Product Overview

A test point has one job: give a probe a reliable place to land, in a board that has no room for a turret. The two numbers that decide it are the mounting hole and the height above the board. A 1.0 mm hole snaps into place and holds during wave soldering, while a 1.6 mm hole takes a larger terminal and stands higher. Both are through hole parts with a phosphor bronze terminal and a silver plate, so the contact resistance stays low after reflow and after a few hundred probe touches.

Colour is not decoration. A red base on a supply rail and a black base on ground lets a technician find the right node without a drawing, and the same body is made in five colours so a board can be keyed by function. That is worth more than it sounds on a board with ten test points in a row, where a probe on the wrong one can short two rails together through the instrument ground.

Where the board is tested in a fixture rather than by hand, a spring loaded pin is the contact. It has a defined working height, a spring force and a rated life, and it compresses to take up the tolerance between the fixture and the board. The Mill-Max 0906 parts are 2 A contacts with a 2.50 to 3.48 mm working range and a life of up to 1,000,000 cycles, which is the number that matters when a fixture runs every board for a year.

Key Specifications

ParameterValueApplies to
Mounting hole1.0 mm, 1.6 mmLoop test points
Installed height4.6 mm to 8.9 mm above boardPer part number
Terminal materialPhosphor bronze, silver plateLoop test points
Base materialNylon 46 or PBT, UL 94 V-0Per part number
ColoursRed, black, white, orange, yellow5000 series
Loop inside diameter1.25 mm5000 series
Board thickness1.57 mm and 2.36 mm supportedLoop test points
Spring pin current2 A maximum0906 series
Spring pin working height2.50 to 3.48 mm0906 series
Spring pin force15 gf initial, 60 gf at mid compression0906-0 series
LifeUp to 1,000,000 cycles0906 series
Operating temperature-45 to 85 C on loop parts, -55 to 125 C on spring pinsPer part number

Included Models and Order Codes

The rows below are the loop test points and spring contacts we quote most for production testing and field service. The mounting hole and the height above the board are given for every loop part, since those decide whether a probe can reach the node. Spring pins carry their working height and force, which is what a fixture is built around.

Part NumberTypeMountingHeight or Working RangeNotes
5000Miniature loop test point, red1.0 mm hole, snap in4.6 mm installed1.25 mm loop, silver plate, -45 to 85 C
5001Miniature loop test point, black1.0 mm hole, snap in4.6 mm installedSame body as 5000, ground coding
5002Miniature loop test point, white1.0 mm hole, snap in4.6 mm installedSame body, alternate colour
5003Miniature loop test point, orange1.0 mm hole, snap in4.6 mm installedSame body, alternate colour
5004Miniature loop test point, yellow1.0 mm hole, snap in4.6 mm installedSame body, alternate colour
5011Multipurpose test point1.6 mm hole8.13 mm long, 3.18 mm diameterNylon 46 base, silver plate, 1.57 and 2.36 mm board
5017Multipurpose test point, reel1.6 mm holePer 5011 body5,000 pieces per reel for placement
0906-0-15-20-76-14-11-0Spring loaded pin, standard tailThrough hole, 0.51 mm hole2.50 to 3.48 mm working2 A, 15 gf initial, 60 gf mid, 1,000,000 cycles
0906-1-15-20-75-14-11-0Spring loaded pin, standard tailThrough hole, 0.51 mm hole2.50 to 3.48 mm workingGold plated, 1,000,000 cycles at mid stroke

Key Features

Hole and height together – Both numbers are given per part, because a probe that cannot reach the loop is no use even if the hole fits.

Colour keyed nodes – Five colours on one body let a board be keyed by rail, which prevents a probe landing on the wrong node.

Snap in retention – The legs hold the part flat through wave soldering, which is where a loose test point usually goes missing.

Loop size stated – A 1.25 mm inside diameter takes a hook probe or a clip, and the figure is quoted rather than assumed.

Fixture contacts included – Spring pins carry working height, force and life, so a bed of nails can be dimensioned from the page.

Reel option – The 1.6 mm part is available on reel for lines that place test points with the rest of the parts.

Applications

These parts are used on production test fixtures, service access points, calibration headers and prototype boards.

Production test and calibration – A 1.0 mm loop on a 4.6 mm height gives a clip or a hook probe a place to land on a dense board, and five colours let the fixture operator find the rail without a drawing.

Bed of nails fixtures – A 2 A spring pin with a 2.50 to 3.48 mm working range takes up the tolerance between the fixture plate and the board, and the 1,000,000 cycle life covers a year of boards.

Field service access – A taller 1.6 mm part stands above a conformal coat and a connector body, so a technician can reach a node on a board that is already in the enclosure.

Test points are placed on the SUPERB PCB at the nodes named in the test plan, and their height is checked against the enclosure on the SUPERB PCBA.

Sourcing and Cross-Reference

Test points are ordered on hole size, height and colour, and the height is the one that gets missed. A 4.6 mm loop under a tall connector cannot be reached with a straight probe, and a 1.0 mm snap in part in a 1.6 mm hole falls through. We confirm the board thickness and the clearance above the point before quoting, then match the body that fits.

For fixtures the spring pin is the part that has to be right. Working height, force and life are all published, and a pin chosen on length alone will either not compress enough to take up tolerance or will compress past its rated stroke and lose force. We quote the pin with its working range and confirm the fixture plate thickness that goes with it.

SUPERB Assembly probes each test point after reflow and confirms it is not bridged to a neighbouring pad before the board goes to the fixture.

Q: Can you supply a test point that fits our existing 1.0 mm hole and stands above the conformal coat?

A: SUPERB Tech quotes the test point with the fixture pin that will touch it, so the two are matched before the fixture is drilled.

Why Buy Test Points Through SUPERB

  1. Hole and height confirmed: Both are checked against the board, so the part neither falls through nor hides under a component.
  2. Colour coding available: Five colours on one body let the board be keyed by rail without a second part number.
  3. Fixture pins specified: Working height, force and life are quoted, so a fixture is built around published numbers.
  4. Reel for volume: The 1.6 mm part is offered on reel where the line places it with the rest of the parts.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Pin Headers and Female Sockets, Board to Board and FPC Connectors, Tactile and Slide Switches, Verify Original Components.