Contact Us
  • Home
  • COMPONENTS
  • Photointerrupters and Optical Switches for Position Detection

Photointerrupters and Optical Switches for Position Detection

A photointerrupter is chosen on slot width, aperture and output type, because those three set the resolution and the circuit around it. Transmissive parts on this page run from a 2 mm slot in a 5.2 mm tall body to a 5 mm slot 12 mm deep. Reflective parts sense a target at about 3 mm and suit paper, label and flag detection. All of them need a defined aperture or a comparator, and the page states which parts include one.
quote now

Product Specifications

Product Overview

An optical switch is the cheapest way to detect an end stop, a card edge, a shutter or a rotating flag, and it works without contact and without a magnet. The transmissive type puts an infrared emitter and a phototransistor face to face across a slot: anything opaque in the slot blocks the beam and the output changes. The reflective type puts both in one housing and reads light returned from a surface a few millimetres away. Neither is a logic device on its own; the output is a phototransistor current, so a resistor and usually a comparator sit behind it.

Resolution is set by the aperture, not by the slot. A 5 mm slot with a 0.5 mm aperture resolves a 0.5 x 2.2 mm object, while a 2 mm slot body with a 1.2 x 0.4 mm aperture resolves a finer edge because the beam is narrower. That is why two parts with the same slot width behave differently on a thin flag. The slot depth matters too: a 5 mm wide slot that is 12 mm deep holds a moving carriage straighter than an 8 mm deep one, at the cost of space.

Temperature and output decide the rest. Standard moulded parts are rated to 85 C, and the EE-SX1041 is rated to 95 C for builds that sit near a heater or a lamp housing. Where the signal has to drive a PLC input directly, a part with a built in amplifier and an NPN output is used instead of a bare phototransistor, and the current limit resistor moves inside the housing. We list the output type on every row so the interface is not guessed from the part photo.

Key Specifications

ParameterValueApplies to
Sensing methodTransmissive slot, reflectivePer part number
Slot width2 mm, 2.8 mm, 3 mm, 3.4 mm, 5 mmTransmissive parts
Slot depth4.4 to 12 mmTransmissive parts
Aperture0.4 x 1.2 mm to 0.5 mm widePer part number
Sensing objectOpaque, 0.5 x 1.5 mm minimum and largerPer part number
OutputPhototransistor, or NPN open collector with amplifierPer part number
Reflective distance3 mm nominalGP2S700HCP
Operating temperatureUp to 85 C standard, 95 C on EE-SX1041Per part number
Emitter forward currentTypically 20 mA continuous, 50 mA peakPer part number
MountingThrough hole, or leadless tape and reel for reflowPer part number

Included Models and Order Codes

The rows below are the slot and reflective parts we quote most for position, edge and flag detection. Slot width and aperture are both given, because the aperture is what sets the smallest object the part can see. Where the maker gives a temperature limit above the standard 85 C, it is stated in the row.

Part NumberTypeSlot or GapApertureNotes
EE-SX1018Transmissive, phototransistor2 mm slot, 4.5 mm deepNarrow slit mouldedOpaque object 0.5 x 1.5 mm minimum
EE-SX1103Transmissive, phototransistor2 mm slot1.2 x 0.4 mm5.2 mm tall body, PCB terminals
EE-SX1025Transmissive, phototransistor2.8 mm slot, 4.4 mm deepNarrow slit moulded5.4 mm tall low profile body
EE-SX198Transmissive, phototransistor3 mm slot, 7.5 mm deepMoulded slit0.6 g body, PCB mounting
EE-SX1071Transmissive, phototransistor3.4 mm slot, 7.2 mm deepMoulded slitOpaque object 0.5 x 2.1 mm minimum
EE-SX1041Transmissive, phototransistor5 mm slot, 8.2 mm deep0.5 mm wideRated to 95 C, 0.5 x 2.2 mm object
EE-SX1042Transmissive, phototransistor5 mm slot, 12 mm deepMoulded slitDeep slot for a moving carriage
GP1S094HCZ0FTransmissive, phototransistor3 mm gap, 0.3 mm slit0.3 mmCompact package, non contact switching
GP2S700HCPReflective, phototransistor3 mm sensing distanceLong focal distanceLeadless package, tape and reel, 6 V reverse

Key Features

Aperture given with slot – Slot width alone does not set resolution, so the aperture is quoted next to it on every row.

Slot depth included – A deep slot holds a moving flag straighter, and the depth is stated where the maker publishes it.

Output type explicit – Phototransistor and amplified NPN parts are separated, so the interface circuit is known before the order.

High temperature option – The EE-SX1041 is rated to 95 C, which matters where the sensor sits near a lamp or a heater.

Reflective part included – A 3 mm reflective part covers label, paper and surface detection where a slot cannot be fitted.

Through hole and reflow – Moulded through hole parts and a leadless tape and reel part are both listed, matching the assembly process.

Applications

These parts detect position, presence and edge in printers, vending units, access control, medical pumps and industrial panels.

End stop and home position – A 5 mm slot part with a 0.5 mm aperture catches a moulded flag on a carriage and gives a repeatable home position without a mechanical switch to wear out.

Card, paper and label edge – A 2 mm slot body sees a 0.5 mm edge, which is the resolution needed for ticket, label and card detection where the media is thin.

Shutter and door interlock – A reflective part at 3 mm detects a shutter blade or a door flag where the mechanism has no room for a fork, and the phototransistor output can be biased for a slow moving target.

The sensor is wired to the SUPERB PCB with its current limit resistor, and the flag position is checked on the SUPERB PCBA before the enclosure is closed.

Sourcing and Cross-Reference

Optical switches are ordered on slot, aperture, output and mounting, and the slot is the only one most buyers ask about. A part with the right slot and the wrong aperture will still switch, but it will not resolve a thin flag, and that shows up only at the end of a build. We ask for the object size and the interface circuit as well as the slot, then match the part that satisfies all four.

Many of these bodies are long lived but not always in stock at short notice, and the moulded part is usually tied to one maker. Where a second source is needed, the substitute is chosen on aperture and output rather than form, and the difference in sensing distance is stated so the flag can be checked before the change is released.

SUPERB Assembly checks the aperture is clear of flux and that the flag breaks the beam at both ends of travel on the first article.

Q: Can you supply a drop in replacement for a slot sensor that is no longer available, with the same aperture?

A: SUPERB Tech quotes the slot part with the resistor value for the supply used, so the output is not left to be worked out at the bench.

Why Buy Photointerrupters Through SUPERB

  1. Aperture matched to the flag: The smallest object the part can see is confirmed before quoting, not after the first build.
  2. Interface known up front: Phototransistor and amplified output parts are quoted against the circuit that will read them.
  3. Temperature checked: Where the sensor sits near a heat source, the 95 C part is offered rather than the standard 85 C body.
  4. Substitute validated on the flag: A replacement is compared on aperture and sensing distance, so the mechanism is checked before release.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Phototransistors for Optical Sensing, Inductive and Photoelectric Sensors, LED Indicators and Optocouplers, Source Obsolete Components.