Card Edge Connectors for Backplanes and Riser Cards
Product Specifications
Product Overview
A card edge connector holds a plug in board by its edge, and the edge itself carries the contacts. The board is made with gold plated fingers, the connector is soldered to the mother board, and the two meet when the card is pushed home. Nothing on the harness has to be crimped, which is why the arrangement survives in backplanes, riser cards, instrument modules and power supplies where a board has to come out for service.
The EDAC 307 series is the 3.96 mm part. Contact spacing is 3.96 mm and row spacing 5.08 mm, the body accepts a card of 1.57 mm, and the rating is 5 A continuous with 1800 V AC rms between adjacent contacts. The working range is -40 to +105 C and the termination is a through hole printed circuit tail in a staggered pattern. This is the pitch used where a card carries a supply rail as well as signals, because the wider contact spacing gives more copper on the finger and more contact area in the spring.
The Sullins GBB series is the high density part. Contact centres are 1.27 mm, the contact is a hairpin bellows with a normal force of 150 g minimum, and the rating is 1 A per contact. The card window is 0.062 inch plus or minus 0.008 inch, which is 1.57 mm plus or minus 0.20 mm, so the card thickness over the fingers has to be held tighter than on the 3.96 mm family. The insulator is polyamide PA9T, the working range is -65 to +125 C, and the contacts are gold plated at 10 micro inches over the contact area.
The figure that decides whether a card edge order works is the card thickness over the fingers, not the nominal board thickness. A 1.6 mm board with 70 micrometres of copper and 5 micrometres of gold on each side is thicker at the finger than the laminate figure suggests, and a board that is at the top of the tolerance opens a bellows contact beyond its elastic range. The 1.27 mm family states its window as a tolerance for that reason, and the 3.96 mm family is more forgiving but not unlimited.
Readout is the second figure. A dual readout body has contacts on both sides of the card, and a single readout body only on one. A dual readout connector on a board with fingers on one side still works, because the unused row simply rests on bare laminate, but a single readout connector on a board with fingers on both sides leaves half the signals unconnected. The table below states the readout per part so that the two are not mixed.
The mounting style is the third. A body with no ears is held by its solder tails alone, which is enough on a short card in a rack with a guide. A body with a threaded insert takes a jack screw, which is what stops a card walking out of a connector under vibration. Where the connector is at the edge of a chassis, the mounting ears and the board locks are usually the reason a particular order code is chosen rather than another.
Key Specifications
| Parameter | Value | Applies to |
|---|---|---|
| Contact spacing | 3.96 mm, 1.27 mm | EDAC 307, Sullins GBB |
| Row spacing | 5.08 mm | EDAC 307 series |
| Card thickness | 1.57 mm | EDAC 307 series |
| Card thickness window | 1.57 mm plus or minus 0.20 mm | Sullins GBB series |
| Current per contact | 5 A continuous, 1 A | EDAC 307, Sullins GBB |
| Dielectric withstanding | 1800 V AC rms | EDAC 307 series |
| Contact normal force | 150 g minimum | Sullins GBB series |
| Contact type | Hairpin bellows | Sullins GBB series |
| Contact material | Phosphor bronze | Sullins GBB series |
| Contact plating | Gold, 10 micro inches | Sullins GBB series |
| Insulator | Polyester thermoplastic, polyamide PA9T | EDAC 307, Sullins GBB |
| Operating range | -40 to +105 C, -65 to +125 C | EDAC 307, Sullins GBB |
| Termination | Through hole, staggered solder tail | Both families |
| Readout | Dual readout | Both families |
| Flammability | UL94 V-0 | Both families |
Included Models and Order Codes
The rows below are the card edge bodies we quote most often. Contact spacing and card thickness are given per part because those two decide whether the card seats, and a dash means the maker does not publish that figure.
| Part Number | Spacing | Positions | Card Thickness | Mount | Rating | Notes |
|---|---|---|---|---|---|---|
| 307-016-520-202 | 3.96 mm | 16 (2 x 8) | 1.57 mm | Through hole, PC tail | 5 A, 1800 V AC rms | Dual readout, staggered tails |
| 307-016-520-208 | 3.96 mm | 16 (2 x 8) | 1.57 mm | Through hole, PC tail | 5 A, 1800 V AC rms | Gold on the contact area |
| 307-016-520-212 | 3.96 mm | 16 (2 x 8) | 1.57 mm | Through hole, PC tail | 5 A, 1800 V AC rms | Gold plated contact area, -40 to +105 C |
| 307-020-401-178 | 3.96 mm | 20 | 1.57 mm | Through hole, PC tail | 5 A, 1800 V AC rms | Longer body on the same series |
| GBB20DHAN | 1.27 mm | 40 (2 x 20) | 1.57 mm plus or minus 0.20 mm | Right angle, staggered solder | 1 A per contact | Hairpin bellows, 150 g, -65 to +125 C |
Key Features
Two pitches on one page – The 3.96 mm and the 1.27 mm bodies are listed with their own spacing, because the finger layout on the board already decides which one fits.
Card thickness stated with tolerance – The high density family publishes a window of 1.57 mm plus or minus 0.20 mm, which is the figure a card with heavy copper has to be checked against.
Normal force given – The hairpin bellows contact is rated at 150 g minimum, which is what keeps a card in place in a rack that sees vibration.
High voltage spacing – 1800 V AC rms between contacts is the reason the 3.96 mm body is used where a card carries a supply rail beside the signals.
Mounting hardware options – Plain body, threaded insert and board lock versions are quoted by order code, so a card that must not walk out is not built on a plain body.
Gold on the contact area – Plating thickness is stated per order code, so a card that is inserted many times is not built on a thin flash.
Applications
These connectors are used where a board has to be removable without a cable, and the edge of the board is the interface.
Backplanes and rack systems – A 40 position 1.27 mm body takes a plug in card on a 1.57 mm board, with the 150 g normal force holding the card against vibration in the rack.
Power supplies and motor drives – A 3.96 mm body carries a supply rail beside the control signals on the same card edge, with the 1800 V AC spacing keeping the rails apart.
Instrument modules and risers – A 16 position body at the edge of a module lets a function board be swapped in the field, with the staggered tails taking the insertion force off a single row.
The connector sits at the edge of the SUPERB PCB, so the gold finger length and the bevel are set by the connector rather than by the board file. On the SUPERB PCBA route the fingers are masked before the first solder step, because a finger that takes solder will not seat in a bellows contact.
Sourcing and Cross-Reference
A card edge connector is bought by spacing and approved by card thickness. When a board is being replaced on an existing backplane, the first question is the finger pitch already on the mother board, because a 1.27 mm card will not go into a 3.96 mm body and the reverse is worse. The second question is the plated thickness over the fingers, because that is what the bellows contact actually sees.
Where a connector is no longer offered in a particular position count, the honest answer is usually a different body on the same spacing rather than an adapter. A card edge interface has no room for an adapter, and an adapter adds a second contact pair in series with the signal. We quote the same spacing in another position count, or the same position count in another mounting style, and state which of the two figures moved.
The third point is the finger finish. A finger that has taken solder will not seat in a bellows contact, and a finger that is bare copper will oxidise in a humid rack. The board house has to mask the fingers through the assembly steps, and the plating over the finger has to be gold over nickel rather than a flash over copper. On a card that is inserted often, that finish is the difference between a contact that holds its force and one that wears through in a year.
SUPERB Assembly checks the card thickness and the insertion squareness on the first unit of every lot, because a card that goes in at an angle spreads the bellows and the contact never comes back to its normal force.
Q: Can you supply a 1.27 mm card edge body for 40 positions that takes our 1.57 mm board, and confirm the card window and the normal force before we make the panel?
A: Send the contact spacing, the board thickness over the fingers and the number of positions. The SUPERB Tech desk quotes the connector with the readout and the mounting style, because a dual readout body on a single sided finger layout gives half the contacts nothing to touch.
Why Buy Card Edge Connectors Through SUPERB
- Spacing read from the board: The order is built from the finger pitch that is already on the mother board, which is where a card edge mismatch starts.
- Card window stated: The high density family is quoted with its 0.20 mm tolerance, so a heavy copper card is checked before the panel is made.
- Readout confirmed: Dual and single readout bodies are not mixed, so a finger layout on both sides is not fed into a one sided body.
- Mounting style chosen: Threaded insert and board lock versions are quoted by order code, so a card that must not walk out is not built on a plain body.
- Fingers kept clean at assembly: The fingers are masked through the solder steps, because a tinned finger does not seat in a bellows contact.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Board to Board and FPC Connectors for Compact Assemblies, DIN and Circular Connectors for Panel Wiring, PCB Card Guides and Board Retainers for Rack Cards, SIM and Memory Card Holders for Field Accessible Storage, Obsolete Part Cross Reference Hub.