Contact Us
  • Home
  • COMPONENTS
  • Panel Potentiometers and Control Knobs for Front Panel Adjustment

Panel Potentiometers and Control Knobs for Front Panel Adjustment

A panel control is chosen on shaft, mounting and life, because the value is the easy part and the mechanics decide whether it lasts. The 9 mm parts on this page turn 280 degrees and run 5,000 to 10,000 cycles at 0.05 W. A 12 mm body adds a longer 20 mm flatted shaft for a taller front panel. Knobs are listed with the shaft diameter and the number of turns the dial reads.
quote now

Product Specifications

Product Overview

A front panel control is a mechanical part as much as an electrical one. The resistive element sets the value and the taper, but the shaft length, the shaft style and the way the body snaps into the panel decide whether the knob lines up and whether the part survives being turned every day. The 9 mm family is the common answer for a compact instrument: a 9.8 mm body, a 280 degree travel, and a snap in clip that holds the part to the panel without a nut.

Two shaft styles cover most builds. A flatted shaft takes a knob with a set screw or a matching flat, and a knurled shaft takes a push on knob with a matching spline. The length has to be chosen against the panel thickness plus the knob depth, which is why the same body is offered at 15, 20, 25 and 30 mm. A 12 mm body is used where the panel is thicker or the knob is deeper, and it carries a longer 20 mm shaft at the same 10 kohm value.

Life is the number to compare. The 9 mm carbon parts are rated at 10,000 cycles for the PTV09 family and 5,000 cycles for the RK09K, at 0.05 W and 20 VDC. That is enough for a setup control that is adjusted occasionally and not enough for a volume control on a unit that is used all day. Where the control is turned constantly, a different family with a longer life is the right answer, and we say so rather than quote the cheaper part.

Key Specifications

ParameterValueApplies to
Body size9 mm, 12 mmPer part number
Resistance range1 kohm to 1 MohmPTV09 series
Resistance toleranceplus or minus 20 percentPer part number
TaperLinear, or audioPer part number
Power rating0.05 W9 mm parts
Maximum voltage20 VDC, 50 VACPTV09 series
Mechanical angle280 degrees, plus or minus 5PTV09 and RK09K
Shaft6 mm flatted or knurled, 15 to 30 mmPer part number
Rotational life5,000 or 10,000 cyclesPer part number
Operating temperature-10 to 50 C on PTV09, -10 to 70 C on RK09KPer part number
MountingSnap in clip, PCB pins, panel bushPer part number
Knob22.2 mm dial, 6.35 mm shaft, 15 turnsH-22 series

Included Models and Order Codes

The rows below are the panel controls and knobs we quote most for instrument front panels and audio equipment. Shaft diameter and length are given because they decide whether an existing knob fits. Life is stated as the maker rates it, at the load the maker specifies.

Part NumberBodyValue and TaperShaftLife and Notes
PTV09A-4020F-B1039 mm, snap in10 kohm, linear6 mm flatted, 20 mm10,000 cycles, 0.05 W, IP40
PTV111-4420A-B10312 mm10 kohm, linear6 mm flatted, 20 mmLonger body for a thicker panel
RK09K1130A8G9 mm, snap in10 kohm, 1B linear6 mm knurled, 15 mm5,000 cycles, 280 degrees, 0.05 W
H-22-6AKnobCounting dial, 15 turns6.35 mm shaft22.2 mm diameter, chrome, numbered dial
H-22-6A-BKnobCounting dial, 15 turns6.35 mm shaft22.2 mm diameter, black, numbered dial

Key Features

Shaft first – Diameter, style and length are given for every part, so an existing knob is matched before the value is discussed.

Life stated – 10,000 cycles on the PTV09 and 5,000 on the RK09K are quoted, because a setup control and a daily control need different parts.

Body size separated – 9 mm and 12 mm parts are listed apart, since the panel cut out and the knob depth follow the body.

Taper included – Linear and audio tapers are named, which matters on a volume control where a linear part sounds wrong.

Knob turns matched – The 15 turn dial is listed with the 6.35 mm shaft it fits, so the dial reading matches the multi turn part behind it.

Temperature range given – 50 C on the PTV09 and 70 C on the RK09K are both stated, which decides the part for a warm enclosure.

Applications

These controls are used on instrument front panels, audio equipment, test gear and industrial operator panels.

Instrument setup control – A 9 mm 10 kohm linear part with a 20 mm flatted shaft sits behind a small knob and is adjusted at commissioning, which suits the 10,000 cycle rating.

Audio level control – A 10 kohm audio taper part at 0.05 W drives a line level stage, and the knurled shaft takes a push on knob without a set screw.

Multi turn dial setting – A 15 turn counting dial on a 6.35 mm shaft gives a readable number for a bias or threshold setting that has to be repeated on every unit.

The control is wired to the SUPERB PCB through a short harness, and the shaft length is checked against the panel before the SUPERB PCBA is fitted.

Sourcing and Cross-Reference

A panel control request usually names the value and stops there. The shaft is what decides whether the part can be used at all, so we ask for the panel thickness, the knob and the mounting method, then match a body that fits all three. A 15 mm shaft in a 3 mm panel leaves a stub that a knob cannot grip, and a 30 mm shaft in a deep panel leaves the body floating behind the face.

Taper is the second question. A linear part in a volume position gives a control that does nothing over the first half of its travel, and that is a deliberate choice rather than a fault, so it is settled before the order. Where a multi turn setting has to be read, the counting dial is quoted with the shaft it fits so the number on the dial matches the number of turns the part can make.

SUPERB Assembly sets each control to its marked position and checks the knob does not rub the panel after the front plate is fitted.

Q: Can you supply a panel control with the same shaft length and flat as the knob we already use?

A: SUPERB Tech quotes the control with the knob and the shaft length as one set, so the front panel does not arrive with a mismatch.

Why Buy Panel Controls Through SUPERB

  1. Shaft matched to the knob: Diameter, flat or spline and length are confirmed, so the knob fits on the first build.
  2. Life matched to the use: A 5,000 cycle part is not offered for a control that is turned daily, and the difference is stated.
  3. Taper agreed in writing: Linear and audio parts are quoted by name, so a volume control is not built with the wrong curve.
  4. Dial and shaft together: The counting dial is quoted with the shaft it fits, so the reading and the turns agree.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Trimmer Potentiometers, Tactile and Slide Switches, OLED and Character LCD Modules, Component Sourcing Guide.