Screw Terminal Blocks and Pluggable Connectors for Field Wiring A field wiring connector is chosen on pitch, current and wire range, because those three decide the copper area and the space left on the board edge. Fixed blocks on this page run from 2.54 mm to 5.0 mm pitch at 10 to 18 A, while the two piece pluggable parts reach 32 A at 7.62 mm. UL and IEC ratings differ on the same part, so both are listed wherever the maker publishes them. Each row lists pitch, current, voltage, wire range and terminal style.
Inductive Proximity and Photoelectric Sensors for Automation A machine builder needs a sensor that repeats, not one that reaches far, so sensing distance and differential travel are read together. The inductive part on this page is an M18 body at 5 mm, and the photoelectric family covers 15 m through beam, 4 m retro reflective and 100 mm diffuse. Output type decides the wiring: NPN or PNP, light on or dark on, three wire at 12 to 24 VDC. Each row lists distance, output, response time and protection class.
Ceramic Chip Antennas for GNSS and Short Range Radios A chip antenna is a small ceramic resonator that only behaves as specified on the ground plane and matching network the maker used for the measurement. The 2.4 GHz parts on this page give 0.5 dBi to 2 dBi of peak gain and 9.5 dB of return loss across 2400 to 2500 MHz. Every part needs a matching network, and the values differ between the two layouts the maker publishes. Each row lists band, gain, return loss and maximum input power.
Tactile and Slide Switches for Front Panel Control A front panel switch is picked on operating force, travel and the number of operations, because the electrical load is almost always small. Tactile parts on this page run from 0.98 N to 2.6 N and carry 1 to 50 mA at 3 to 24 VDC. Sealed SMT types survive a washing step, while open through hole types do not and must be added after cleaning. Each row lists force, rating, height and cycle life.
OLED and Character LCD Display Modules for Instrument Panels A display module is chosen on controller, interface and supply, because those three decide the firmware and the level shifter before the glass size is discussed. Character LCD parts on this page use the ST7066U and PIC16F690 controllers with 8 bit or 4 bit parallel buses at 5 V. Colour OLED and TFT parts run from 2.4 V to 3.6 V with SPI or parallel interfaces and need a separate display rail. Each row lists format, controller, interface and supply.
PIN Diode Limiters for RF Receiver Front End Protection A PIN limiter is a passive part that turns a receiver input into a short when the signal is too large, and it needs no supply to do that. Threshold levels on this page run from 10 dBm to 37 dBm, and continuous input ratings from 36 dBm to 44 dBm. The choice between them is set by the largest signal the antenna can deliver and by the insertion loss the receiver can afford. Each row lists threshold, CW and peak ratings, junction capacitance and series resistance.
High Power LED Emitters for Illumination and Infrared A high power emitter is a thermal part before it is an optical part, because the flux figure is quoted at a junction temperature the board has to hold. White parts on this page run to 2000 mA and infrared parts to 2 A pulsed, and both need a metal core board and a defined solder pad. Flux bins and forward voltage are given per order code, since the same family ships in several bins. Every row lists drive current, forward voltage and viewing angle.
RF Coaxial Connectors and Adapters for Test and Antenna Runs A coaxial connector is the only place on an RF board where the 50 ohm line leaves the laminate, so its VSWR and its launch geometry set the measurement floor. Micro coaxial parts such as U.FL reach 8 GHz and take a 1.13 mm cable, while SMA parts reach 18 GHz on a board or bulkhead launch. Mating cycles run from 30 on a micro part to 500 on SMA, which decides whether the connector goes on the product or on the test fixture. Each row lists frequency limit, impedance, mounting and cycles.
Board-to-Board and FPC Connectors for Compact Assemblies The connector sets the stack height of a two board product and the flex radius of an FPC, so it is chosen before the enclosure is fixed. Pitch runs from 0.4 mm on mezzanine pairs to 2.0 mm on wire-to-board headers, and per contact current from 0.5 A to 2 A. FPC receptacles need a 0.3 mm cable and a locking actuator that survives rework at the test bench. Every row below lists pitch, positions, mated height and mounting style, because those four decide fit.
GaN HEMT RF Power Transistors for Broadband Amplifiers GaN on SiC RF power transistors for broadband amplifiers from 6 W to 120 W. 28 V, 40 V and 50 V rails, unmatched parts that are matched on the board. Flange, pill, DFN and die options for radar, electronic warfare and radio links. Cross reference and long term supply are checked against the maker data sheet.
RF Detector Diodes and Zero-Bias Schottky Detectors Schottky detector diodes for RF power measurement and receiver level detection. Low barrier parts work without bias current, which keeps the detector noise floor low. Single, series pair and quad configurations are supplied in SOT-23, SOT-143 and 0201. Replacement and long term supply are checked against the maker data sheet.
Isolated Amplifiers for Shunt and Voltage Sensing Isolation amplifiers that pass a millivolt shunt signal or a bus voltage across a certified barrier. Working voltage, withstand voltage and drift are all quoted per part number. Parts from TI, Analog Devices, Broadcom and Skyworks are supplied for drives, inverters and battery systems. Cross reference and long term supply are checked before quoting.
Fully Differential Amplifiers and ADC Drivers A fully differential amplifier converts a single ended signal into a balanced pair and sets the output common mode to match the ADC reference. Bandwidth runs from 145 MHz on the precision parts to 8 GHz on the RF front end driver, and the choice follows the sampling rate and the resolution. Input noise of 1.1 nV per root hertz to 5 nV per root hertz sets the resolution floor once the source impedance is known. Supply range of 2.7 V to 5.4 V on the precision parts and 3 V to plus or minus 5 V on the current feedback parts decides the headroom. Each row lists bandwidth, slew rate, noise, supply and package, because those four decide whether an 18 bit ADC keeps its last two bits.
Time-of-Flight Distance Sensors for Ranging and Presence A time of flight sensor measures the flight time of a short infrared pulse, so the reading depends on distance and not on the colour or the reflectance of the target. Range runs from 60 cm on the smallest part to 5 m on the long range single zone part, and the field of view from 25 degrees to a 65 degree diagonal with 64 zones. Zoned parts report a small depth map, which turns a distance reading into presence detection across a doorway. The 940 nm emitter is class 1, so the module needs no eye safety label of its own when it is used behind a cover glass. Every row lists range, field of view, update rate and interface, because those decide the mounting height and the host bus.
PIR Motion Sensors and Pyroelectric Detector Modules A PIR sensor detects a change in infrared radiation, not motion itself, so a warm body crossing the field produces a pulse while a steady heat source does not. Module level parts such as the HC-SR501 include the comparator, the relay driver and the adjustable delay, so the output is already a logic level. Bare detectors such as the LHI878 need a lens and a signal chain, and they are chosen when the product has its own optics and firmware. Quiescent current runs from about 50 uA on the module to 170 uA on the digital PaPIRs part, which decides whether a battery product can use it. Every row lists supply, current, angle, range and output, because those decide the lens and the power budget.
Hall Effect Switches and Latches for Position Sensing A digital Hall switch reports one bit when a magnet crosses its threshold, so a lid, a valve or a rotor needs no contact and no wear surface. The threshold spread matters more than the typical value: a 4.8 mT maximum operate point on the DRV5032 variants leaves room for magnet tolerance and air gap. Sampling rate sets the current, from 0.54 uA at 5 Hz to 5.2 uA at 80 Hz on the same family. Omnipolar parts respond to either pole, which removes the magnet orientation error from assembly. Each row lists supply, threshold, output type and package, because those decide the magnet and the pull up resistor.
LoRa and Sub-GHz Transceiver Modules for Long Range Links A LoRa module carries the SX126x or SX127x radio, the matching network and the crystal, and reaches 5 km to 12 km at 22 dBm to 30 dBm in the 868 MHz and 433 MHz bands. Sensitivity of -147 dBm at 0.3 kbps is what buys that range, and it comes at a data rate of 0.018 kbps to 62.5 kbps. The SX1262 parts cut receive current to 6.8 mA against 10 mA or more on the older SX1276 parts. Bare SPI modules need the host to drive the radio, while the UART modules take AT commands and remove the driver work. Each row lists band, output power, sensitivity, interface and supply, because those decide the link budget and the host firmware.
Wi-Fi and Bluetooth Modules for Industrial IoT Devices A Wi-Fi module puts the radio, the matching network, the crystal and the antenna on a certified board, so the product only needs a 3.3 V rail and a serial or SDIO port. Flash and PSRAM decide which part fits: 4 MB carries a sensor sketch, 8 MB to 16 MB carries an over the air image plus a display buffer. Peak transmit current reaches 379 mA on the dual core part at 19.5 dBm, which sets the bulk capacitor on a coin cell or solar product. The ESP32-S3 and ESP32-C3 families add BLE 5 and a native USB port, and the C3 moves to a RISC-V core at a lower active current. Every row lists core, memory, antenna and footprint, because those decide the firmware image and the enclosure opening.
LTE Cat 1 and Cat 4 Modules for Cellular Telemetry Cat 4 modules carry 150 Mbps downlink for camera and gateway products, while Cat M1 and NB-IoT parts keep a link alive on a few microamps in sleep. Band coverage decides which order code ships to which market, and the regional suffix is the part of the code most often quoted wrong. The supply window is 3.3 V to 4.3 V on the Cat 4 family and 2.6 V to 4.8 V on the BG77, so one rail does not suit every part. Peak transmit current reaches close to 2 A on a Cat 4 module, which sets the bulk capacitor and the supply trace on the carrier board. Each row lists bands, data rate, supply and package, because those decide the certification route as well as the layout.
GNSS Receiver Modules for Positioning and Timing A GNSS module puts the receiver, the compensated clock, the filters and the antenna feed in one screened can that is already characterised. Tracking sensitivity from -165 dBm to -167 dBm decides whether a tracker keeps a fix inside a vehicle or under dense canopy. Concurrent reception of four constellations raises the visible satellite count in street canyons where one system drops below four satellites. Timing parts are quoted on 1PPS accuracy, which is 30 ns RMS on the M9 and M10 engines. Every row lists supply range, host interface and footprint, because those three decide the carrier board.
MEMS and Programmable Oscillators for Clock Trees A MEMS oscillator replaces the quartz blank with a silicon resonator and a temperature compensated circuit, so the frequency is set in test and not by the cut of a crystal. That makes every frequency a stocked part number, removes the custom frequency lead time, and holds stability under shock and vibration that breaks a quartz blank. The table below lists frequency range, stability, output, supply and package for the codes we quote most often.
Wireless Charging Receiver and Transmitter ICs A Qi link is built from a transmitter that drives a coil and a receiver that rectifies what the coil picks up, and the two ends are separate part numbers. The receiver sets the output rail and the thermal budget in the product; the transmitter sets the input rail, the coil current and the foreign object detection. The table below gives output power, rectified voltage, protocol version and package for the codes we quote most often.
Bluetooth Low Energy SoCs for Wireless Sensor Nodes A BLE SoC puts the radio, the stack and the application core on one die, so the node needs no host processor and no firmware split. Three things pick the part: flash for the stack plus over the air update, the data rate and range the radio must hold, and the sleep current the cell can afford. The table below lists those three against supply range and package for the codes we quote most often.
RF Fixed Attenuators and Terminations for Instrument Chains A fixed attenuator sets a level, protects a mixer and improves a match, with no bias and no control line. The SMA 2 W family covers 1 dB to 40 dB from DC to 18 GHz with 1.20 to 1.30 to 1 VSWR up to 12.4 GHz. Terminations keep an unused port at 50 ohm so a combiner or a switch does not see a reflection. Every line lists accuracy, VSWR by band, average power and connector, because those are what the level plan is built on.
Ceramic Resonators and Crystal Filters for Clock and IF Stages A ceramic resonator gives a microcontroller a clock with no external load capacitors and no startup circuit. Initial tolerance is plus or minus 0.5 percent, which suits UART and I2C timing where a crystal is more accuracy than the job needs. The 10.7 MHz ceramic filters set the IF bandwidth of an FM receiver at 110 kHz to 150 kHz with 330 ohm terminations. Each row lists tolerance, temperature stability, bandwidth and package, because those decide the parts around it.
Piezo Buzzers and Magnetic Audio Indicators for Alerts A transducer needs a square wave from the host, an indicator only needs a DC voltage. Piezo parts run at 3 V to 220 V with currents under 20 mA and reach the highest sound pressure in a thin package. Magnetic indicators run from 3 V to 12 V at about 30 mA and give a steady tone with a narrow frequency tolerance. Every sound pressure figure is quoted at 10 cm with the drive condition, because the distance and the voltage change the number.
Thermoelectric Coolers and Peltier Modules for Precision Cooling A Peltier module moves heat when current flows, and reversing the current moves it the other way. Sub watt modules stabilise laser diodes, photodiodes and crystal oscillators where the load is small and the set point is tight. Larger single stage modules pump 7 W to 53 W for instrument chambers and reagent blocks. Every figure is quoted at a stated hot side temperature, because Qc and delta T both fall as that temperature rises.
Isolated Gate Drivers and SiC Gate Drive Supplies Isolated drivers break the gate loop from the control ground, so a high side switch can be driven without a bootstrap that runs out at high duty cycle. Single channel parts carry desaturation detection and a Miller clamp for IGBT and SiC turn off. Dual channel parts cover half bridge, dual high side and dual low side from one package with programmable dead time. Each row lists isolation rating, peak current, delay and UVLO, because those set the gate resistor and the layout of the barrier.
Gas Sensors for Air Quality and Leak Detection Photoacoustic CO2 parts measure 400 to 5000 ppm with an accuracy stated against the reading, not a single number. VOC and NOx index sensors report a 1 to 500 index over I2C and need no gas bottle for calibration. Heated metal oxide cells cover combustible gas and carbon monoxide at the lowest cost per point, with a preheat and a heater cycle. Each row lists range, supply, current and package, because those decide the enclosure and the power budget.
Rotary Encoders and Optical Encoders for Motion Feedback Contacting encoders give 12 or 24 pulses per turn for a front panel knob, with detents and a push switch in the same body. Reflective optical encoders resolve 75 to 180 lines per inch on a codewheel and need no shaft coupling. A magnetic part reads absolute angle as 12 bit over I2C for motor and valve feedback. Each row lists pulses or lines, output type, supply and mounting, because those decide the firmware and the bracket.
Thermal Fuses and Temperature Cutoffs for Battery and Heater Safety Axial one shot cutoffs cover 72 C to 240 C, with 10 A, 15 A and 25 A ratings at 250 VAC. The opening temperature is not the number printed in the code, so the table lists the tested value for each order code. Holding temperature and maximum overshoot are listed as well, because those set the margin in normal operation. Surface mount protectors add a heater terminal for an active cutoff inside a lithium pack.
Current Transformers and AC Current Sensing for Energy Metering Split core clamps cover 5 A to 100 A with 50 mA, 0.333 V or 1 V output through a 13 mm opening. PCB current transformers run 5 A to 25 A at 1000:1, with class 0.1 and class 0.2 phase error quoted per code. Current type voltage transformers take 2 mA in and return 2 mA, so a mains level reaches an ADC through one resistor. Burden, phase error and isolation are listed per part, because those three decide the metering class.
Ultrasonic Transducers and Distance Sensors for Level and Proximity Open structure 40 kHz parts come as a matched transmitter and receiver pair, at 120 dB sound pressure and -63 dB sensitivity. Sealed modules cover 20 cm to 765 cm at 1 cm resolution, with analog, pulse width, RS232 or I2C output. Average supply current is 2 mA to 4.4 mA, so a battery node can range continuously. Each row lists beam angle, supply range, read rate and package, because those set the mounting and the firmware loop.
Small Signal Bipolar Transistors for Switching and Amplification The complementary pairs cover 40 V at 200 mA and 45 V at 100 mA in TO-92 and SOT-23. The 800 mA part carries four times the current of the standard switching transistor at 40 V. Gain groups run from 100 to 300 and from 200 to 450, and the group letter is part of the code. Transition frequency, power rating and package are listed per code, because they set the drive.
Ambient Light and Proximity Sensors for Display and Presence Ambient light parts cover 0.01 lx to 83 klx or 0 lx to 140 klx, with 16 to 23 bit effective resolution. Proximity parts detect a hand at up to 200 mm with an integrated infrared emitter and a 16 bit output. All of them report over I2C at 400 kHz and run from 1.6 V to 3.6 V or 2.5 V to 3.6 V. Resolution, range, supply and package are listed per code, because they set the window and the flex.
Resistor Arrays and Precision Thin Film Resistors Thin film chip resistors reach 0.1 percent tolerance and 25 ppm per degree in 0603 at 0.1 W. Four element arrays put 10 k at 1 percent or 5 percent into a 1206 or an 0804 body. Array elements track each other at 200 ppm per degree, which is the figure that matters in a divider. Package, power per element, maximum voltage and operating range are listed per part number.
Load Cells and Strain Gauge Bridges for Weighing Single point aluminium cells cover 50 kg to 500 kg in OIML R60 class C3, C4 and C5. The C3 part holds combined error to 0.023 percent of full scale, the C5 part to 0.014 percent. Miniature cells run from 100 g to 1500 g with 0.6 mV/V to 1.0 mV/V of output and 0.05 percent error. Foil strain gauges at 350 ohm and a gauge factor of 2.0 to 2.2 are listed for bridge builds.
Phototransistors for Optical Sensing and Isolation Leaded parts run from 75 uA to 350 uA of light current at 100 lx, with half angles from 20 degrees to 50 degrees. The 1206 surface mount part gives 50 uA at 100 lx with a 60 degree half angle and an AEC-Q101 grade. Infrared parts in TO-18 reach 7.5 mA to 15 mA at 1 mW per square centimetre and 850 nm. Collector voltage, dark current and rise time are listed per code, because they set the load resistor.
Varactor and Tuning Diodes for RF Circuits Hyperabrupt parts cover 1.4 pF to 12.6 pF at 1 V, with a 1.5 to 2.8 ratio to 3 V and series resistance from 0.6 ohm to 2.9 ohm. The linear UHF part covers 17.5 pF to 21 pF at 0.5 V with an 8.9 to 12 ratio to 28 V. The VHF part covers 26 pF to 32 pF at 3 V with a 5 to 6.5 ratio to 25 V. Reverse voltage, package and power rating are listed per code, because they set the tuning range and the loop.
Zener Diodes for Voltage Reference and Clamping Axial 1 W parts cover 3.3 V to 56 V in DO-41, with test currents from 76 mA down to 4.5 mA. Axial 0.5 W parts in DO-35 cover the same voltage range at 20 mA test current. Surface mount parts in SOT-23 cover 5.6 V to 39 V at 5 mA and 300 mW. Zener impedance and reverse leakage are listed per code, because they decide the regulation and the loading.