Contact Us
  • Home
  • COMPONENTS
  • Seven Segment LED Displays for Instrument Readouts

Seven Segment LED Displays for Instrument Readouts

A seven segment display is chosen on digit height, common pin and colour, and then on whether the driver can supply the current.\nThe 14.22 mm parts here give 3,600 to 8,000 ucd at 10 mA in high efficiency red, and 14,000 to 34,000 ucd in super bright red.\nForward voltage is 1.9 V typical at 10 mA, with a 30 mA DC and 160 mA pulsed limit on the standard red part.\nCommon anode and common cathode versions share the same 10 pin package and the same 2.54 mm pin row.
quote now

Product Specifications

Product Overview

A seven segment display is still the clearest way to show a number on an instrument that has to be read from a metre away in poor light. It is a simple part: seven LED chips and a decimal point, moulded into a package with a light pipe over each segment. What decides whether it works in a product is the digit height, the common pin, the colour and the current the driver can supply.

The 0.56 inch parts on this page have a 14.22 mm digit height and the industry standard 10 pin package, with pins on a 2.54 mm row and a 15.24 mm row spacing. That means a board laid out for one maker can take another maker part without a change, which is the reason this package has survived so long. The package is 12.7 mm wide and 8 mm deep, with a grey face and white segments for contrast.

The high efficiency red parts use GaAsP on GaP, with a peak wavelength of 627 nm and a dominant wavelength of 617 nm. Luminous intensity is 3,600 ucd minimum and 8,000 ucd typical at 10 mA, and forward voltage is 1.9 V typical, 2.3 V maximum at 10 mA. The super bright red part uses GaAlAs, with a peak at 655 nm, a dominant wavelength of 640 nm, and 14,000 to 34,000 ucd at 10 mA, at a forward voltage of 1.8 V typical. Both are 30 mA DC parts, with a 160 mA pulsed rating at a tenth duty cycle.

Common anode and common cathode are not interchangeable on a board. A common anode display has all the anodes joined and is driven by pulling each cathode low, which suits a driver with open drain or sink outputs. A common cathode display has all the cathodes joined and is driven by pulling each anode high, which suits a source driver or a port pin that can supply current. The pin numbers differ between the two, so the footprint has to match the part that is fitted. Both versions are listed here with the same package, so a change of driver can be met by a change of display rather than a change of board.

The Broadcom HDSP family in the same table is the second source for this package. It includes single digit common anode and common cathode parts, a plus or minus one overflow version, and two digit parts, in red, AlGaAs red, yellow and green. The HDSP-5503 is listed as obsolete by the maker, which makes it a last time buy part rather than a current one, and we say so before quoting it. Where a customer needs a long production life, the Kingbright parts are the current route and the HDSP numbers are the drop in alternative for an existing build.

Key Specifications

ParameterValueApplies to
Digit height14.22 mm (0.56 inch)All parts on this page
Package10 pin DIP, 2.54 mm pin row, 15.24 mm row spacing0.56 inch single digit parts
Body size12.7 mm wide, 8 mm deepKingbright 0.56 inch parts
ConfigurationCommon anode or common cathode, right hand decimalPer part number
Luminous intensity, high efficiency red3,600 ucd minimum, 8,000 ucd typical at 10 mASA56-11EWA and SC56-11EWA
Luminous intensity, super bright red14,000 ucd minimum, 34,000 ucd typical at 10 mASA56-11SRWA
Forward voltage at 10 mA1.9 V typical, 2.3 V maximumSA56-11EWA and SC56-11EWA
Forward voltage at 10 mA1.8 V typical, 2.3 V maximumSA56-11SRWA
Peak wavelength627 nm high efficiency red, 655 nm super bright redKingbright parts
DC forward current30 mA maximum per segmentKingbright parts
Peak forward current160 mA at 1/10 duty, 0.1 ms pulseSA56-11EWA
Power dissipation75 mW per segmentKingbright parts
Operating temperature-40 to +85 CKingbright parts
Viewing distanceUp to 7 m0.56 inch parts
SolderingWave solder only, 260 C for 3 to 5 s, not reflow compatibleThrough hole displays

Included Models and Order Codes

The rows below are the single and dual digit parts we quote most often. The Broadcom rows give the configuration and the package; where the maker does not publish an intensity figure in the summary sheet we leave a dash rather than guess. All rows are through hole parts.

Part NumberDigit HeightConfigurationColourVf at 10 mAPackageNotes
SA56-11EWA14.22 mmCommon anode, right hand decimalHigh efficiency red1.9 V10 pin DIP3,600 to 8,000 ucd at 10 mA
SC56-11EWA14.22 mmCommon cathode, right hand decimalHigh efficiency red1.9 V10 pin DIPSame optical data as the anode part
SA56-11SRWA14.22 mmCommon anode, right hand decimalSuper bright red1.8 V10 pin DIP14,000 to 34,000 ucd at 10 mA
HDSP-550314.22 mmCommon cathode, right hand decimalRed2.1 V10 pin DIP2.8 mcd typical at 20 mA, listed obsolete
HDSP-550114.22 mmCommon anode, right hand decimalRed-10 pin DIPAnode version of the 5503
HDSP-570314.22 mmCommon cathode, right hand decimalYellow-10 pin DIPYellow family, same pinout
HDSP-560314.22 mmCommon cathode, right hand decimalGreen-10 pin DIPGreen family, same pinout
HDSP-H15314.22 mmCommon cathode, right hand decimalAlGaAs red-10 pin DIPDeep red, higher contrast
HDSP-552314.22 mmTwo digit common cathodeRed-10 pin DIPTwo digits in one package
HDSP-550714.22 mmCommon anode, plus or minus one overflowRed-10 pin DIPOverflow indication for a counter

Key Features

Industry standard footprint – The 10 pin package with a 2.54 mm pin row and a 15.24 mm row spacing lets a board take parts from more than one maker without a layout change.

Anode and cathode in one package size – Both common pin arrangements use the same body, so a change of driver can be met by a change of display rather than a board change.

Stated intensity at 10 mA – The luminous intensity is given at a stated current, which is the only way to compare two parts that are quoted at different drive levels.

Two red technologies – High efficiency red at 3,600 to 8,000 ucd and super bright red at 14,000 to 34,000 ucd cover both a low current instrument and a display that has to be read in daylight.

Overflow and two digit variants – The same family includes a plus or minus one overflow part and a two digit part, so a counter can be built without a second display family.

Wave solder rating stated – The 260 C for 3 to 5 seconds rating and the note that the part is not reflow compatible are given up front, because a display that goes through reflow will fail.

Applications

These displays are used where a number has to be read without a backlight and without a graphics controller.

Bench instruments – A 0.56 inch display shows voltage, current or resistance from a metre away, with a segment current set by a single resistor per digit.

Panel meters and controllers – A two digit part shows a channel number or a setpoint next to a single digit part that shows the value.

Timers and counters – The overflow part gives a plus or minus one indication when a counter passes its range, which is clearer than a blank display.

The display is placed on the SUPERB PCB in the same pass as the driver, and the SUPERB PCBA route checks the segment current against the resistor value on the build sheet before the first article is signed off.

Sourcing and Cross-Reference

The 0.56 inch package is standard, so a replacement usually exists. The trap is the common pin and the pin numbering. A common anode part and a common cathode part of the same size have different internal connections, and a board that was laid out for one will light the wrong segments with the other. We confirm the common pin and the segment mapping before quoting, and we ask for the old part number rather than the colour alone.

The second trap is the soldering route. These are through hole displays and they are not reflow compatible. A board that is reflowed on the top side and wave soldered on the bottom can take them, but a board that is fully reflowed cannot, and the answer there is a different display family rather than a different part number. We ask for the process at quote time, not after the first batch.

Obsolete parts are common in this family. The HDSP-5503 is listed as obsolete by the maker, and a customer who has it on an approved build needs a last time buy or a drop in replacement. The Kingbright parts share the package and the pinout, so they are the usual drop in, but the segment current has to be checked because the intensity at a given current is not the same. That check is done before the replacement is quoted.

SUPERB Assembly keeps the displays in their tubes until the wave, because a display that has been dropped can have a cracked segment that only shows once it is lit.

Q: Can you supply a common cathode 0.56 inch display as a drop in for an obsolete part, and confirm the segment current stays within the driver rating?

A: Tell us the digit height, the common pin and the colour you need, and whether the board is wave or reflow soldered. The SUPERB Tech desk quotes the display and the matching socket so the pin length suits the board.

Why Buy Seven Segment Displays Through SUPERB

  1. Common pin confirmed: The anode or cathode arrangement and the segment mapping are checked against the old part before a replacement is quoted.
  2. Same package, two makers: The Kingbright and Broadcom parts share the 10 pin package, so a second source does not need a board change.
  3. Intensity at a stated current: Luminous intensity is given at 10 mA, which makes two parts comparable instead of one number at an unstated drive level.
  4. Process checked first: The wave solder rating and the reflow limitation are stated, so a display is not quoted for a board that cannot take it.
  5. Obsolete parts handled openly: A part that the maker has discontinued is labelled as such, and the drop in replacement is checked for current before it is offered.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: OLED and Character LCD Display Modules for Instrument Panels, High Power LED Emitters for Illumination and Infrared, LED Indicators and Optocouplers for Status and Isolation, Test Points and Spring Contacts for Board Probing, Discrete Semiconductor Cross Reference.