Contact Us
  • Home
  • COMPONENTS
  • Banana Jacks and Binding Posts for Test and Bench Panels

Banana Jacks and Binding Posts for Test and Bench Panels

A banana jack is a 4 mm socket with a solder tag, and a binding post is the same socket with a nut that also takes a wire or a spade lug.\nThe panel parts here are rated 15 A with a 2500 VDC hands free limit, for panels from 1.6 mm to 9.5 mm thick.\nBodies are brass with tin or gold plating, insulators are polycarbonate or PPS, and the high temperature version runs to 220 C.\nNon insulated swage mount jacks are listed for a board that needs a test point at 15 A.
quote now

Product Specifications

Product Overview

A banana jack is the connector that makes a test lead fit a panel. It is a 4 mm socket with a spring contact inside, a threaded body, and a solder tag or a turret terminal at the back. A binding post adds a knurled nut on the front, so the same point can take a banana plug, a bare wire or a spade lug. Both are panel parts, and both are chosen on current, panel thickness and whether the front has to be touch proof.

The panel jacks on this page are the Pomona 1581, 2854 and 4900. All three fit a panel from 1.6 mm to 9.5 mm thick, with a quarter inch lock washer and a hex nut at the back. The 1581 body is brass with a bright tin plate, the 2854 body is brass with a gold plate, and the 4900 uses a polyphenylene sulfide insulator for a 220 C working temperature instead of the 115 C of the polycarbonate parts. Current rating is 15 A, and the hands free voltage limit is 2500 VDC.

The binding post is the Pomona 3760. It takes a banana plug, a wire or a spade lug, mounts in a panel from 1.77 mm to 6.35 mm thick, and carries the same 15 A and 2.5 kV ratings. The difference from a jack is the front nut: a post can be tightened onto a wire, which is what a bench supply or a test box needs when the connection is made once and left.

The board level parts are the Keystone 575 series, a non insulated swage mount jack that accepts a 4.4 mm plug and carries 15 A. It is fixed by swaging the body into the board, which gives a mechanical joint that survives a test lead being pulled sideways. The body lengths are 5.5 mm, 6.7 mm and 8.9 mm, so the same part can sit on a thin board or reach through a thicker one.

The number to read first is not the current but the panel thickness. A jack with a 1.6 to 9.5 mm range will not clamp a 12 mm panel, and a post with a 1.77 to 6.35 mm range will not reach through a 9 mm wall. The second number is the voltage limit for hands free use, which is 2500 VDC on these parts but only 30 Vrms or 60 VDC if the part is held in the hand. Both are stated below, because a test bench is exactly where the second limit is forgotten.

Key Specifications

ParameterValueApplies to
Socket size4 mm bananaAll parts on this page
Current rating15 APomona 1581, 2854, 4900 and 3760, Keystone 575
Hands free voltage2500 VDC maximumPomona panel parts
Held in hand limit30 Vrms or 60 VDCPomona panel parts
Panel thickness, jack1.6 mm to 9.5 mmPomona 1581, 2854, 4900
Panel thickness, post1.77 mm to 6.35 mmPomona 3760
Body materialBrass, tin plated or gold platedPer part number
InsulatorPolycarbonate, or PPS on the high temperature partPomona panel parts
Operating temperature115 CPomona 1581 and 2854
Operating temperature220 CPomona 4900
Mounting hardwareQuarter inch lock washer and hex nut, brassPomona panel parts
Board mountSwage mount, accepts a 4.4 mm plugKeystone 575 series
Body length5.5 mm, 6.7 mm or 8.9 mmKeystone 575-4, 575-6, 575-8

Included Models and Order Codes

The rows below are the panel and board parts we quote most often. The colour suffix is part of the order code on the Pomona parts, so -0 is black and -2 is red. A dash means the maker does not publish that figure.

Part NumberTypeSocketRatingPanel or BoardBody and PlatingNotes
1581-0Panel jack, black4 mm15 A, 2500 VDC1.6 to 9.5 mm panelBrass, tin platedPolycarbonate insulator, 115 C
1581-2Panel jack, red4 mm15 A, 2500 VDC1.6 to 9.5 mm panelBrass, tin platedSame part in red
2854-0Panel jack, black4 mm15 A, 2500 VDC1.6 to 9.5 mm panelBrass, gold platedGold body for a low resistance joint
2854-2Panel jack, red4 mm15 A, 2500 VDC1.6 to 9.5 mm panelBrass, gold platedGold body, red
4900-0Panel jack, black4 mm15 A, 2500 VDC1.6 to 9.5 mm panelBrass, nickel platedPPS insulator, 220 C
4900-6Panel jack, blue4 mm15 A, 2500 VDC1.6 to 9.5 mm panelBrass, nickel platedPPS insulator, 220 C
3760-0Binding post, black4 mm15 A, 2.5 kV1.77 to 6.35 mm panelBrass, tin platedTakes a wire or a spade lug
3760-2Binding post, red4 mm15 A, 2.5 kV1.77 to 6.35 mm panelBrass, tin platedTakes a wire or a spade lug
575-4Swage mount jack4.4 mm plug15 ABoard, 5.5 mm bodyBrass, nickel platedNon insulated, nut and lug included
575-6Swage mount jack4.4 mm plug15 ABoard, 6.7 mm bodyBrass, nickel platedFor a thicker board
575-8Swage mount jack4.4 mm plug15 ABoard, 8.9 mm bodyBrass, nickel platedLongest body in the series

Key Features

Panel thickness stated – Every panel part gives the thickness range it clamps, which is the first number that decides whether the part fits.

Two voltage limits – The 2500 VDC hands free limit and the 30 Vrms or 60 VDC held in hand limit are both stated, because a test bench is where the second one matters.

Tin, gold and high temperature – The same jack body is offered in tin, gold and a PPS insulated version for 220 C, so a soldering iron near the panel is not a reason to change the layout.

Post takes three terminations – A binding post accepts a banana plug, a bare wire and a spade lug, which is what a bench supply or a test box needs.

Swage mount on the board – The Keystone jack is swaged into the board, so a test lead pulled sideways does not lift a pad.

Colour coded parts – Black and red are stocked as separate order codes, so polarity is read on the panel rather than in the drawing.

Applications

These parts are used on test boxes, bench instruments and any panel where a 4 mm lead is connected by hand.

Bench power supplies – A binding post takes a banana plug for a quick test and a bare wire for a permanent installation, at 15 A.

Test boxes and jigs – A panel jack gives a 4 mm test point on a jig, with the current rating to carry a supply rail rather than only a signal.

Instrument front panels – A gold plated jack keeps the contact resistance low on a measurement input, and the colour code shows polarity.

The jack or post is fitted on the SUPERB PCB or on the panel of the same instrument, and the SUPERB PCBA route checks the torque on the hex nut so the insulator does not crack.

Sourcing and Cross-Reference

These parts are simple, and the usual shortage is a colour or a plating rather than the part itself. The Pomona jack is available in nine colours, and a customer who needs a specific colour for a panel may find that only black and red are on the shelf. A different colour is a different order code, not a different part, so the lead time is the only difference and we say so before quoting.

The second point is the panel thickness. A jack that clamps 1.6 to 9.5 mm will not hold on a 12 mm panel, and a post that clamps up to 6.35 mm will not reach through a 9 mm wall. When the panel is thicker, the answer is a longer body or a different family, not a washer. We ask for the panel thickness with the order and check it against the range on the drawing.

Gold plating is worth its cost only where the contact resistance matters. On a supply output at 15 A, a tin plated brass body is fine. On a measurement input that carries a microvolt signal, the gold body keeps the thermal EMF and the contact resistance stable. We quote the plating that matches the signal, and we do not put a gold part on a supply rail where it adds cost without benefit.

SUPERB Assembly fits the panel parts after the board is in the case, because a post that is tightened before the panel is located can spin and damage the wire behind it.

Q: Can you supply the panel jack in the colour we need for a 9 mm panel, together with the nut and washer, and confirm the current rating?

A: Send the panel thickness, the current you need to carry and whether the part has to be touch proof. The SUPERB Tech desk quotes the jack, the nut and the washer as a set for that panel.

Why Buy Banana Jacks Through SUPERB

  1. Panel range checked: The thickness the part clamps is checked against the panel before the order, which avoids a jack that will not tighten.
  2. Plating matched to the signal: Tin for a supply rail and gold for a measurement input are both stocked, and the difference is explained rather than upsold.
  3. Colour as an order code: Black, red and the other standard colours are separate codes, so a panel is wired the same way every time.
  4. Hardware included: The lock washer and hex nut are part of the part, so a panel is not held up for a washer.
  5. Fitted at the right step: The panel parts are fitted after the board is in the case, which keeps the post from spinning and damaging the wire.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Test Points and Spring Contacts for Board Probing, Audio Jacks and DC Power Connectors for Instrument Panels, RF Coaxial Connectors and Adapters for Test and Antenna Runs, DIN and Circular Connectors for Panel Wiring, Connector Cross Reference.