Contact Us
  • Home
  • COMPONENTS
  • Standoffs Spacers and Mounting Hardware for Board Stacks

Standoffs Spacers and Mounting Hardware for Board Stacks

A standoff sets the distance between two boards, and it is the part that decides whether a connector still mates after the screws are tight.\nThe parts here cover M3 threads in brass and zinc plated steel, from 5 mm to 50 mm, in male to female and female to female bodies.\nHex bodies are 5.5 mm across flats, and the round nylon spacers run from 2 mm to 30 mm with inner diameters of 2.2 to 5.2 mm.\nThe snap clip spacer studs hold a board on a 2.1 mm panel without a nut on the far side.
quote now

Product Specifications

Product Overview

A standoff is a mechanical part with an electrical job. It sets the gap between two boards, it carries the load of the stack, and on a metal part it also bonds the two grounds together. The three families on this page cover almost every board stack: a threaded metal standoff, a round plastic spacer, and a snap clip stud that holds a board on a panel without a nut.

The metal parts are the Wurth WA-SSTII and WA-SBRIE series. The WA-SSTII body is machined steel with a zinc plated surface, in M3 by 0.5 thread, in female to female and male to female versions, with a 5.5 mm hex across flats and lengths from 6 mm to 35 mm. The WA-SBRIE body is brass with a nickel plated surface, in the same M3 thread and the same 5.5 mm hex, with a male thread on one end and a female thread on the other, so two boards can be stacked and the screw goes into the far end of the standoff.

The plastic parts are the Wurth WA-SPARO round spacers and the WA-SNTI spacer studs. The round spacers are nylon 66, in lengths from 2 mm to 30 mm, with inner diameters of 2.2, 2.7, 3.2, 4.2 and 5.2 mm, and outer diameters of 4, 5, 6, 8 and 10 mm. They are used as a plain bush where a screw passes through both boards and a metal standoff is not wanted, for example where the two grounds must stay separate. The snap clip studs are nylon with a 6 mm hex, an M3 internal thread and a clip that holds a 2.1 mm panel, in lengths from 6 mm to 50 mm.

The choice between brass, steel and nylon is not only a cost decision. Brass takes a nickel plate that stays bright and does not gall in a stainless screw, which is why it is the usual part on an instrument that will be serviced. Zinc plated steel is stronger and cheaper, and it is the right part where the stack carries weight or where the standoff is also a ground path. Nylon is an insulator, so it is used where a board has to be isolated, or where a metal part would short a track on the underside.

The measurement that is most often wrong is the length. A male to female standoff is quoted by its body length, and the male thread adds to the overall height, so a 10 mm body with a 6 mm male thread gives 16 mm between the boards only if the thread goes fully into the far board. On the Wurth parts the body length and the overall length are both published, and the two are not the same. We quote the body length, the thread length and the overall length, and we ask for the gap that has to be held rather than the length of the old part alone.

Key Specifications

ParameterValueApplies to
ThreadM3 x 0.5, male and femaleWA-SSTII and WA-SBRIE
Hex across flats5.5 mmWA-SSTII and WA-SBRIE
Body materialSteel, zinc platedWA-SSTII
Body materialBrass, nickel platedWA-SBRIE
Length range, metal6 mm to 35 mm body lengthWA-SSTII
ConfigurationFemale to female, or male to femalePer part number
Round spacer materialNylon 66WA-SPARO
Round spacer length2 mm to 30 mmWA-SPARO
Round spacer inner diameter2.2 mm to 5.2 mmWA-SPARO
Round spacer outer diameter4 mm to 10 mmWA-SPARO
Snap clip stud materialPolyamide, blackWA-SNTI
Snap clip panel thickness2.1 mmWA-SNTI 973 series
Snap clip hex6 mm across flats, M3 internal threadWA-SNTI 973 series
Operating temperatureUp to 110 C on the nylon partsWA-SNTI

Included Models and Order Codes

The rows below are the lengths and configurations we quote most often. The metal rows give the body length and the overall length where the maker publishes both, because a male thread adds to the stack height. A dash means the maker does not publish that figure.

Part NumberTypeThreadBody LengthHex or DiameterMaterialNotes
970100321Hex standoff, female to femaleM310 mm5.5 mm hexSteel, zinc platedThrough threaded both ends
970150321Hex standoff, female to femaleM315 mm5.5 mm hexSteel, zinc platedSame body, longer
970350321Hex standoff, female to femaleM335 mm5.5 mm hexSteel, zinc platedTall stack, 35 mm
971120324Hex standoff, male to femaleM312 mm5.5 mm hexBrass, nickel platedOverall length 18 mm
971170324Hex standoff, male to femaleM317 mm5.5 mm hexBrass, nickel platedOverall length 25 mm
R30-3001302Hex standoff, male to femaleM313 mm5.5 mm hexBrassHarwin R30 series
R30-1010502Hex standoff, female to femaleM35 mm5.5 mm hexBrassShort spacer for a tight stack
960100042Round spacerClearance for M310 mm3.2 mm ID, 6 mm ODNylon 66Plain bush, no thread
960100116Round spacerClearance for M510 mm5.2 mm ID, 10 mm ODNylon 66Insulating bush for a larger screw
973100365Snap clip spacer studM3 internal10 mm6 mm hexPolyamide, blackClips a 2.1 mm panel, no nut

Key Features

Body and overall length both given – On the male to female parts the body length and the overall length are stated, so the stack height is not short by the length of the thread.

Brass and steel in one hex – Both materials share the 5.5 mm hex and the M3 thread, so a change for corrosion or for strength does not change the clearance around the part.

Nylon where isolation is needed – The round spacers are an insulator, which is the part to use where a metal standoff would short a track or join two grounds that have to stay apart.

Snap clip without a nut – The clip stud holds a board on a 2.1 mm panel from one side, which removes a nut and a washer from the assembly step.

Lengths from 5 mm to 50 mm – The range covers a single board on a chassis and a three board stack, without a special part for each gap.

Stated panel thickness – The clip stud is quoted with the panel thickness it holds, because a clip for a 2.1 mm panel will not hold a 3 mm panel.

Applications

These parts are used in every product that has more than one board or a board on a chassis.

Two board stacks – A male to female brass standoff holds a processor board above a power board, with the screw entering the female end from below.

Board to chassis mounting – A female to female steel standoff sets the board off a metal chassis and provides the ground bond through the screws.

Isolated boards – A nylon round spacer holds a board off a metal case where the ground has to stay floating, for example on a measurement front end.

The standoffs are fitted on the SUPERB PCB stack before the boards are screwed into the enclosure, and the SUPERB PCBA route checks the stack height against the connector and the panel drawing.

Sourcing and Cross-Reference

Standoffs are bought by length, and the length is where most orders go wrong. A male to female part has a body length and an overall length, and a customer who orders by the old part number can end up with a stack that is 6 mm short. We ask for the gap between the boards, the panel thickness and the screw length, and we quote the part whose overall length closes that gap.

The second point is the thread. M3 by 0.5 is standard, but a standoff with a rolled thread and a screw with a cut thread can bind after a few assembly cycles, and a stainless screw in a brass standoff can gall. On a product that is assembled and serviced, a nickel plated brass standoff with a stainless screw and a small amount of thread lubricant is the usual answer. On a product that is assembled once, zinc plated steel is enough.

Plastic parts have their own limit. A nylon spacer creeps under a sustained load, so a stack that is tightened hard will lose its preload over a year. Where a plastic spacer is used for isolation, we recommend a shoulder washer and a controlled torque rather than a tight screw. That is a build note, not a part change, and it is worth saying before the first batch rather than after.

SUPERB Assembly keeps the brass parts in their bags until the final screw step, because a nickel plated thread that has been handled with bare hands will tarnish before the product ships.

Q: Can you supply the standoff, the screw and the washer as a set for a fixed stack height, and confirm the overall length including the male thread?

A: Send the thread, the length between the boards and the panel thickness. The SUPERB Tech desk quotes the standoff, the screw and the washer as a set so the stack height is fixed by the parts and not by the torque.

Why Buy Standoffs Through SUPERB

  1. Gap quoted, not just length: The quote is built from the gap between the boards and the panel thickness, so the stack closes on the parts rather than on the torque.
  2. Overall length stated: Male to female parts carry both the body length and the overall length, which is where a short stack usually comes from.
  3. Material matched to the joint: Brass for a serviced instrument and zinc plated steel for a loaded stack are both listed in the same hex and thread.
  4. Isolation available: Nylon spacers and clip studs cover the case where a metal part would short a track or join two grounds.
  5. Fitted as a set: The standoff, screw and washer are quoted together and fitted at the final screw step, so the stack height is checked once.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: EMI Shielding Cans and Contact Gaskets for RF Boards, Heat Sinks and Thermal Interface Pads for Power Boards, Screw Terminal Blocks and Pluggable Connectors for Field Wiring, Board to Board and FPC Connectors for Compact Assemblies, Passive Component Cross Reference.