Contact Us
  • Home
  • COMPONENTS
  • Audio Jacks and DC Power Connectors for Instrument Panels

Audio Jacks and DC Power Connectors for Instrument Panels

A panel jack is chosen on the plug it must accept, the current it must carry and the number of insertions it will see. The 3.5 mm parts on this page carry 1 A at 12 V and run 5,000 cycles, in horizontal through hole form. DC jacks cover a 1.3 mm and a 2.0 mm centre pin, at 2.0 and 2.5 A, with and without a switch contact. Barrel and plug diameters are stated, because 2.0 mm and 2.5 mm plugs do not interchange.
quote now

Product Specifications

Product Overview

Two connectors sit on almost every instrument panel: a headphone or line jack and a DC inlet. Both are mechanical parts that carry a small current, and both fail in the same way, which is at the contact after a few thousand insertions. The useful specification is therefore the plug it accepts, the current rating and the life, not the body colour or the mounting angle. A 3.5 mm jack will not take a 2.5 mm plug, and a 2.0 mm DC jack will not take a 2.5 mm barrel, however similar the bodies look.

The DC side has an extra trap. A jack with a switch contact opens or closes a circuit when the plug is inserted, and that contact is how a unit switches from battery to adapter without a separate changeover. If the switch is not needed the part is cheaper, but if it is needed and missing, the battery stays connected while the adapter is plugged in. We list whether a switch is present on every DC row, and the 5,000 cycle life figure is given where the maker publishes it.

Audio jacks are simpler but not trivial. A stereo jack has three conductors and the tip, ring and sleeve have to match the plug wiring, which depends on whether the source is a headset with a microphone or a plain line plug. The parts here are three conductor types with no internal switch, at 1 A and 12 V, which covers line in, line out and headphone outputs on instrument panels.

Key Specifications

ParameterValueApplies to
Audio standard3.5 mm, 3 conductors, stereoAudio jacks
DC centre pin1.3 mm, 2.0 mmDC jacks
DC barrel3.5 mm outer on the 1.3 mm part, 5.5 mm on the 2.0 mm partDC jacks
Rated current1 A audio, 2.0 to 2.5 A DCPer part number
Rated voltage12 VDC audio, 24 VDC DC jacksPer part number
Contact resistance30 to 50 m ohm typicalPer part number
Insulation resistance100 M ohm minimum at 500 VDCPer part number
Withstanding voltage500 VAC for 1 minutePer part number
Life5,000 cyclesPer part number
Switch contactNone on audio, single normally closed on PJ-102APer part number
Operating temperature-25 to 85 CAll parts on this page

Included Models and Order Codes

The rows below are the panel jacks we quote most for instrument, audio and portable equipment. The plug each part accepts is stated first, since that is what the customer cable has to fit. Where a switch contact is fitted, the row says so, because a missing switch changes the battery circuit.

Part NumberTypePlug AcceptedRatingNotes
PJ-102ADC power jack, right angle through hole2.0 mm pin, 5.5 mm barrel2.5 A, 24 VDCSingle normally closed switch, -25 to 85 C
PJ-031DDC power jack, right angle through hole1.3 mm pin, 3.5 mm barrel2.0 A, 24 VDC1.3 mm centre pin, 5,000 cycles
SJ1-3523N3.5 mm audio jack, right angle through hole3.5 mm TRS plug1 A, 12 VDC3 conductors, no internal switch, 12 x 11 mm body
SJ1-3555NG3.5 mm audio jack, through hole3.5 mm TRS plug1 A, 12 VDC5,000 cycles, 500 VAC withstanding, UL 94 V-0
35RAPC4BHN23.5 mm audio jack, horizontal PC mount3.5 mm TRS plugPer maker curve0.03 ohm contact, 100 M ohm, 500 V withstanding

Key Features

Plug stated first – Every row names the pin and barrel or the audio standard, so a 2.0 mm plug is not ordered for a 1.3 mm jack.

Switch contact disclosed – The PJ-102A switch is named, because that contact decides how the battery and adapter circuit behaves.

Life given where published – 5,000 cycles is stated on the parts the maker rates, which is the number that predicts a panel failure.

Current and voltage together – 1 A at 12 V and 2.5 A at 24 V are not comparable, so both are given on every row.

Through hole and horizontal – Right angle and horizontal parts are separated, matching how the board sits behind the panel.

Contact resistance listed – 30 to 50 m ohm is quoted, which matters on a 1 A DC inlet where the joint is part of the drop.

Applications

These jacks are used on instrument panels, portable test gear, audio units and small power inlets.

Instrument DC inlet – A 2.5 A 24 V jack with a switch contact lets a unit run from an adapter and disconnect the internal cells at the same time, without a separate changeover circuit.

Headphone and line output – A 3.5 mm three conductor jack at 1 A carries a line output to a headset or an amplifier, and the horizontal body keeps the board close to the panel.

Portable and handheld units – A 1.3 mm DC jack takes a small adapter plug on a handheld unit where the inlet has to fit a narrow end panel.

Both jacks are placed at the panel edge of the SUPERB PCB, and the plug depth is checked against the face plate before the SUPERB PCBA is assembled.

Sourcing and Cross-Reference

Panel jacks are ordered on the plug, the current and the switch, and the plug is the one that cannot be adjusted. A customer who sends a photo of the mating plug usually has the barrel right and the pin wrong, so we ask for the plug part number or a caliper reading on the pin and the barrel before quoting. That single check prevents most returns on DC inlets.

The switch contact is the second question. A jack without it is cheaper and smaller, and on a unit that runs from a single supply it makes no difference. On a unit with internal cells it decides whether the cells are still connected when the adapter is inserted, so it is settled from the circuit rather than from the price.

SUPERB Assembly inserts and withdraws each jack five times with the mating plug and checks the switch contact changes state before the unit is packed.

Q: Can you supply a DC jack with the same pin and barrel as our existing adapter plug, including the switch contact?

A: SUPERB Tech quotes the jack with the plug it accepts, so a replacement inlet cannot arrive with a pin size that does not fit the adapter.

Why Buy Panel Jacks Through SUPERB

  1. Plug measured, not guessed: Pin and barrel sizes are confirmed against the mating plug before a part is quoted.
  2. Switch contact checked: The presence of a switch is stated on every DC part, so the battery circuit is not left to chance.
  3. Life quoted: 5,000 cycle parts are identified so a high use panel is not fitted with a short life jack.
  4. Contact resistance given: The joint resistance is known before it becomes part of the supply drop on a 1 A inlet.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: RF Coaxial Connectors and Adapters, Screw Terminal Blocks and Pluggable Connectors, Tactile and Slide Switches, Pin to Pin Cross Reference.