Contact Us
  • Home
  • COMPONENTS
  • DIP and SIP IC Sockets for Through Hole Packages

DIP and SIP IC Sockets for Through Hole Packages

A socket is chosen on three things: the package it takes, the number of times the part will be changed, and the heat the board sees. The stamped open frame DIP sockets here run from 8 to 40 positions on a 2.54 mm pitch, in 7.62 mm and 15.24 mm row spacing, with tin plated phosphor bronze contacts. The machined sockets and strips carry a beryllium copper four finger contact rated 3 A, with 10 mOhm contact resistance and 1,000 insertion cycles. Tail length runs from 3.15 mm to 3.18 mm, which covers boards from 1.0 mm to 1.6 mm.
quote now

Product Specifications

Product Overview

A socket is fitted for one of three reasons: the part is expensive enough that it should not be scrapped with the board, the part has to be replaced in the field, or the part has to be programmed and tested out of circuit. Each reason points at a different body. A cheap stamped socket is right for a part that is inserted once during the build, a machined socket is right for a part that is pulled and refitted, and a strip is right where only a few pins need to be removable.

The Assmann A series is the stamped open frame DIP socket we quote most often. The body is polybutylene terephthalate, the contacts are phosphor bronze with a tin finish, the pitch is 2.54 mm, the tail is 3.15 mm long and the working range is -55 to +85 C. It comes in 7.62 mm row spacing from 8 to 20 positions and in 15.24 mm row spacing for the wide packages, which is the 0.3 inch and 0.6 inch pair that most dual in line parts use.

The Mill-Max machined parts are a different construction. The contact is a four finger beryllium copper sleeve, a size 30 contact, rated 3 A with a contact resistance of 10 mOhm or less and an insulation resistance of 10,000 MOhm. The insulator is PCT polyester, which takes a reflow profile that the cheaper thermoplastic bodies do not, and the working range is -55 to +125 C. The published mechanical life is 1,000 cycles, against a stamped contact that is normally quoted for a single insertion.

The difference between the two is not academic on a production line. A 40 position machined socket has a real insertion force, and a part pressed in by thumb at one end bends the contacts at the other end and opens them. A stamped socket has a much lower force and is more forgiving, but its contacts relax after a few insertions and the contact resistance rises. Where a board is tested in a fixture every day, the machined body is the one that survives the year.

Row spacing and tail length are the two mechanical figures to check. A 0.3 inch socket will not take a 0.6 inch package, and a 3.15 mm tail in a 2.0 mm board leaves the insulator standing off the surface with the solder only on the tail. The parts on this page run from 3.15 mm to 3.18 mm of tail, which suits a 1.0 mm to 1.6 mm board with a normal fillet. A thicker board needs the long tail version of the same series rather than a longer socket.

Single row strips are the third option on the page. The Mill-Max 310 series is a SIP strip in the same machined contact, from 1 to 64 positions on a 2.54 mm pitch, with a 3.18 mm tail and a 2.79 mm insulator height. It is what a board uses when a module has to sit above the surface, or when only the programming pins of a part need to be reachable and the rest are soldered direct.

Key Specifications

ParameterValueApplies to
Contact pitch2.54 mmAll parts on this page
Row spacing7.62 mm and 15.24 mmAssmann A series DIP
Positions8 to 20 in 7.62 mm, 40 in 15.24 mm, 1 to 64 in single rowAssmann A, Mill-Max 310
Stamped contact materialPhosphor bronze, tin platedAssmann A series
Machined contact materialBeryllium copper four finger, size 30Mill-Max 110 and 310
Current per contact3 AMill-Max 110 and 310
Contact resistance10 mOhm maximumMill-Max 110 and 310
Insulation resistance10,000 MOhm minimumMill-Max 110 and 310
Rated voltage100 VRMS and 150 VDCMill-Max 110 and 310
Mechanical life1,000 cycles minimumMill-Max machined contact
Accepted lead diameter0.38 mm to 0.635 mmMill-Max 110 and 310
Tail length3.15 mm, 3.18 mmAssmann A, Mill-Max 110 and 310
Insulator, stamped bodyPolybutylene terephthalateAssmann A series
Insulator, machined bodyPCT polyester, UL94 V-0Mill-Max 110 and 310
Operating range-55 to +85 C, -55 to +125 CAssmann A, Mill-Max
FlammabilityUL94 V-0Mill-Max bodies

Included Models and Order Codes

The rows below are the sockets we quote most often. Row spacing and tail length are given per part because those two decide whether the body sits flat on the board, and a dash means the maker does not publish that figure.

Part NumberTypePositionsRow SpacingContactRatingNotes
A 08-LC-TTDIP, open frame8 (2 x 4)7.62 mmPhosphor bronze, tinSee series data3.15 mm tail, -55 to +85 C
A 14-LC-TTDIP, open frame14 (2 x 7)7.62 mmPhosphor bronze, tinSee series data3.15 mm tail, -55 to +85 C
A 16-LC-TTDIP, open frame16 (2 x 8)7.62 mmPhosphor bronze, tinSee series data3.15 mm tail, -55 to +85 C
A 20-LC-TTDIP, open frame20 (2 x 10)7.62 mmPhosphor bronze, tinSee series data3.15 mm tail, -55 to +85 C
A 40-LC-TTDIP, open frame40 (2 x 20)15.24 mmPhosphor bronze, tinSee series dataWide body, 3.15 mm tail
110-43-316-41-001000DIP, machined16 (2 x 8)7.62 mmBeryllium copper, gold3 A per contact10 mOhm, 1,000 cycles, PCT body
310-43-108-41-001000SIP strip, machined8 (1 x 8)2.54 mm single rowBeryllium copper, gold3 A per contact3.18 mm tail, 2.79 mm height

Key Features

Stamped and machined in one place – The open frame stamped body and the machined four finger body are both on this page, because the choice between them is the number of insertions, not the price.

Cycle life stated – The machined contact is published at 1,000 cycles minimum, which is the figure a test fixture needs; the stamped body is a one time insertion part.

Two row spacings – 7.62 mm and 15.24 mm bodies are listed separately, so a 0.6 inch package is not ordered on a 0.3 inch socket.

Reflow safe insulator – The PCT body on the machined parts takes a reflow profile, which the cheaper thermoplastic bodies on the stamped parts do not.

Tail length matched to the board – 3.15 mm and 3.18 mm tails suit a 1.0 mm to 1.6 mm board with a normal fillet, and the long tail version of the same series is quoted for a thicker board.

Single row strips to 64 pins – The SIP strip covers 1 to 64 positions on a 2.54 mm pitch, which is how a module is lifted above the board or a set of programming pins is left reachable.

Applications

These sockets are used where a part has to be replaceable, programmable or testable without scrapping the board.

Instrument and control boards – A calibration part sits in a machined socket so it is swapped during a service visit, with the 1,000 cycle contact taking the refits.

Test fixtures and burn in racks – A 40 position stamped socket is the cheap interface on a rack that loads the same board every day, and the machined body is used where the socket is loaded by hand.

Line cards and gateways – A programmed part is left in a 0.6 inch socket during the build, and a SIP strip lifts a small module above the surface where a tall capacitor sits beside it.

A socket adds height to the SUPERB PCB, so the part under it is checked against the tallest component beside it before the layout is released. On the SUPERB PCBA route the socket is placed after the reflow step when the insulator cannot take the oven, and before it when the body is a high temperature thermoplastic.

Sourcing and Cross-Reference

A socket is quoted by package and approved by cycle life. The question we ask first is how many times the part will be inserted, because a stamped body quoted for a fixture that is loaded every shift is the wrong part however good the price is. The second question is the board thickness, because a 3.15 mm tail in a 2.0 mm board leaves the insulator off the surface and the solder joint hanging on the tail alone.

The second point is the row spacing. A 0.3 inch socket and a 0.6 inch socket are visually similar in a photo and completely different on a board, and a 40 pin package is normally the 0.6 inch body. Where a part has been moved from a wide package to a narrow one, the socket has to move with it, and the old socket order is not reusable even though the position count is the same.

The third point is the insertion tool. A machined socket with 40 positions needs an even force across the row, and a part pressed in at one end bends the contacts at the other. Where a socket is fitted on a line, we ask whether the line has the tool, and if it does not, the stamped body at a lower insertion force is the practical answer rather than a machined body that arrives damaged.

SUPERB Assembly inserts the part with a proper tool rather than by thumb, because a 40 pin machined socket needs an even force across the row and a part pressed in at one end bends the contacts.

Q: Can you supply a 16 pin machined DIP socket rated for 1,000 insertions, and confirm the row spacing and tail length against our 1.6 mm board?

A: Send the package, the row spacing and how many times the part will be changed. The SUPERB Tech desk quotes the socket by cycle life and tail length, because a stamped body and a machined body are not the same part in a fixture that is loaded every day.

Why Buy IC Sockets Through SUPERB

  1. Cycle life matched to use: The order is built from the number of insertions, so a fixture is not built on a one time insertion body.
  2. Row spacing confirmed: 0.3 inch and 0.6 inch bodies are kept apart, which is the error that stops a 40 pin package from seating.
  3. Tail length against the board: The tail is checked against the board thickness, and the long tail version of the same series is quoted for a thick board.
  4. Stamped and machined both quoted: The cheaper body and the long life body are both available, so the answer is not driven by what is on one shelf.
  5. Insertion handled at assembly: The socket is fitted with a tool rather than by thumb, which is what keeps a 40 position contact row from being bent.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: DIP Switches and Rotary Address Switches for Configuration, Jumper Links and Shunt Headers for Board Configuration, Board to Board and FPC Connectors for Compact Assemblies, Test Points and Spring Contacts for Board Probing, Obsolete Part Cross Reference Hub.