Light Pipes and LED Holders for Front Panel Indicators
Product Specifications
Product Overview
A light pipe is a clear plastic rod that carries the light of a board mounted LED to the front panel. It is used for three reasons. The LED can be placed where the board has room rather than where the panel needs a lamp. The panel hole can be a plain press fit with no lens ring to seal. And the light is confined to the pipe, so a green, amber and red lamp next to each other do not bleed into one another on a dark front panel.
The Bivar PLP2 series is a front mount panel light pipe with a 3 mm round lens and a low profile round face. The body is polycarbonate rated UL94 V-0, the mounting hole is 0.115 in (2.92 mm), and the recommended panel thickness is 0.047 in to 0.093 in, which is 1.19 mm to 2.36 mm. Body length is part of the order code: PLP2-100 is 0.100 in (2.5 mm), PLP2-250 is 0.250 in (6.4 mm), PLP2-500 is 0.500 in (12.7 mm), and the series runs to PLP2-1200 at 1.200 in (30.5 mm).
The PLP5-2 series is the same idea with a 5 mm lens. The flange is 0.197 in (5.0 mm) across, the mounting hole is 0.156 in (3.96 mm), and the panel range is the same 1.19 mm to 2.36 mm. It is offered in a smoked body and in a white diffused body, and the diffused version is the one that spreads the light evenly across the face rather than showing a bright core.
The LPV3 series is a board mount pipe rather than a panel part. It presses into a 0.115 in (2.92 mm) hole in the board and stands vertically to the panel, with a 2.92 mm domed lens at the top. The height is set by the order code, so LPV3-0750DP stands 0.750 in (19.05 mm) above the board. This is the part to use when the panel is a fixed distance from the board and the front of the panel has no room for a flange.
The LED holders are a different answer to the same problem. A right angle holder takes a 3 mm T-1 lamp with two leads and holds it at the board edge, so the light leaves the board horizontally towards a window in the side of the case. The Bivar H-100C to H-103C bodies are moulded nylon, with heights of 0.132 in (3.4 mm) and 0.150 in (3.8 mm) and a 0.200 in (5.1 mm) centreline, and they interlock so two to four stations can be built as one block. The 909-235 body does the same job for a 5 mm T-1 3/4 lamp at 5.97 mm, and the C-174 and C-174L are panel clips that hold a 5 mm lamp in a round cutout.
Two numbers decide whether an indicator works. The first is the gap between the board and the panel, because a pipe that is too short leaves a dark ring and a pipe that is too long pushes the panel out. The second is the panel thickness, because the press fit barb only holds over the 1.19 mm to 2.36 mm range. Both are stated per part below, and both are worth measuring on the first article rather than on the drawing alone.
Key Specifications
| Parameter | Value | Applies to |
|---|---|---|
| Lens size, light pipe | 3 mm or 5 mm | PLP2, PLP5-2, LPV3 |
| Body length, PLP2 | 2.5 mm to 30.5 mm, set by order code | PLP2 series |
| Body length, PLP5-2 | 2.5 mm or 3.2 mm in this list | PLP5-2-100, PLP5-2-125 |
| Panel thickness | 1.19 mm to 2.36 mm | PLP2 and PLP5-2 panel parts |
| Mounting hole, 3 mm pipe | 2.92 mm (0.115 in) | PLP2, LPV3 |
| Mounting hole, 5 mm pipe | 3.96 mm (0.156 in) | PLP5-2 |
| Flange diameter, 5 mm pipe | 5.0 mm (0.197 in) | PLP5-2 |
| Material, light pipe | Polycarbonate, UL94 V-0 | PLP2, PLP5-2 |
| Lens finish | Clear, smoked or white diffused | Per order code |
| Lens, board mount pipe | 2.92 mm domed | LPV3-0750DP |
| Height above board | 19.05 mm (0.750 in) | LPV3-0750DP |
| Material, LED holder | Moulded nylon | H-100C to H-103C, 909-235, C-174 |
| LED size, holder | 3 mm T-1 or 5 mm T-1 3/4 | Per part |
| Holder height, 3 mm | 3.4 mm or 3.8 mm | H-100C and H-101C, H-102C and H-103C |
| Holder centreline | 5.1 mm (0.200 in) | H-100C to H-103C |
| Holder length, 5 mm right angle | 5.97 mm | 909-235 BK |
| Panel clip length, 5 mm | 6.35 mm or 9.02 mm | C-174, C-174L |
| Operating temperature | -40 to +85 C | Moulded nylon holders |
Included Models and Order Codes
The light pipe rows give the body length and the panel thickness, because those two decide whether the pipe closes the gap. The holder rows give the lamp size and the body length. A dash means the maker does not publish that figure.
| Part Number | Lens | Body Length | Mount | Panel Thickness | Finish | Notes |
|---|---|---|---|---|---|---|
| PLP2-100 | 3 mm | 2.5 mm | Front panel, press fit | 1.19 to 2.36 mm | Clear | 2.92 mm hole, low profile face |
| PLP2-125 | 3 mm | 3.2 mm | Front panel, press fit | 1.19 to 2.36 mm | Clear | 2.92 mm hole |
| PLP2-250 | 3 mm | 6.4 mm | Front panel, press fit | 1.19 to 2.36 mm | Clear | 2.92 mm hole |
| PLP2-375 | 3 mm | 9.5 mm | Front panel, press fit | 1.19 to 2.36 mm | Clear | For a thicker front plate |
| PLP2-500 | 3 mm | 12.7 mm | Front panel, press fit | 1.19 to 2.36 mm | Clear | Longest common length |
| PLP5-2-100-S | 5 mm | 2.5 mm | Front panel, press fit | 1.19 to 2.36 mm | Smoked | 3.96 mm hole, 5.0 mm flange |
| PLP5-2-125-D | 5 mm | 3.2 mm | Front panel, press fit | 1.19 to 2.36 mm | White diffused | Even spread across the face |
| LPV3-0750DP | 3 mm | 19.05 mm | Board, press fit | Not a panel part | Clear | 2.92 mm dome, vertical |
LED Holders and Panel Clips
A holder is used where the lamp itself has to be seen, or where the board sits at an angle to the panel. The 3 mm bodies interlock into a block, so a four lamp strip is built from four holders rather than a bracket.
| Part Number | LED Size | Type | Body Length | Material | Notes |
|---|---|---|---|---|---|
| H-100C | 3 mm T-1 | Right angle | 3.4 mm | Nylon, black | Interlocking left end |
| H-101C | 3 mm T-1 | Right angle | 3.4 mm | Nylon, black | Single station, 2 lead |
| H-102C | 3 mm T-1 | Right angle | 3.8 mm | Nylon, black | Interlocking centre |
| H-103C | 3 mm T-1 | Right angle | 3.8 mm | Nylon, black | Interlocking right end |
| H-201C | 3 mm T-1 | Right angle, tall | 9.65 mm | Nylon, black | Taller body for a recessed board |
| 909-235 BK | 5 mm T-1 3/4 | Right angle | 5.97 mm | Nylon, black | 2 lead, board edge |
| C-174 | 5 mm T-1 3/4 | Panel clip | 6.35 mm | Nylon, black | Round cutout, no ring |
| C-174L | 5 mm T-1 3/4 | Panel clip | 9.02 mm | Nylon, black | Longer body for a thick panel |
Key Features
Panel thickness stated – The 1.19 mm to 2.36 mm press fit range is given for every panel pipe, so a 3 mm front plate is not fitted with a part that will not hold.
Body length as an order code – The length is part of the part number, which means a 2.5 mm gap and a 12.7 mm gap are two catalogue parts rather than a special.
Clear, smoked and diffused – A diffused body spreads the light for a status lamp, and a clear body gives a brighter point for a warning lamp.
Board mount option – The LPV3 pipe presses into the board and stands to the panel, which suits a panel with no room for a flange.
Interlocking holders – The 3 mm right angle bodies interlock into a one to four station block, so a lamp strip is built from stock parts.
Two lamp sizes – Holders are listed for 3 mm T-1 and 5 mm T-1 3/4 lamps, so the same panel can carry a small status lamp and a larger indicator.
Applications
These parts are used wherever a lamp has to be seen on the outside of a case while the LED stays on the board.
Instrument front panels – A 3 mm pipe carries a status LED through a 2.92 mm hole in a 2 mm plate, with no lens ring and no light bleed between adjacent lamps.
Network and telecom units – A row of 5 mm pipes shows link and power state on a front panel that is closed and screened, with the LEDs kept back from the surface.
Handheld and sealed cases – A board mount pipe reaches from the board to a window in a sealed case, so the lamp is visible without a hole that has to be gasketed.
The pipe or holder is fitted to the SUPERB PCB through a press fit hole, and the SUPERB PCBA route checks the gap between the board and the panel before the indicator length is ordered.
Sourcing and Cross-Reference
A light pipe is a mechanical part, and the two numbers that decide it are the gap and the panel thickness. A pipe that is 0.5 mm too short leaves a dark ring around the lens on a black panel, and a pipe that is 0.5 mm too long holds the panel off its gasket. We ask for the board to panel gap and the panel thickness with the order, and where a customer only has the old part number we match on the lens size, the length and the hole.
The press fit is the second place an indicator goes wrong. The barb holds over a defined panel range, and a hole that is drilled 0.1 mm oversize lets the pipe sit loose and rotate. A hole that is undersize cracks the flange on insertion. The recommended hole is stated per family, 2.92 mm for the 3 mm parts and 3.96 mm for the 5 mm parts, and it is worth cutting the first panel to that figure rather than to the drawing of the old supplier.
Colour is the third point. A clear pipe shows the colour of the LED itself, a smoked pipe dims it, and a diffused pipe spreads it so the whole face lights rather than a bright dot. On a panel with three lamps close together, a diffused body also reduces the bleed from one lamp to the next. We quote the finish that matches the look the panel needs, and we do not treat the three as interchangeable.
SUPERB Assembly fits the light pipes after the panel is located, because a pipe pressed in before the board is screwed down can be pushed back out of its hole and sit below the surface.
Q: Can you supply a 3 mm light pipe for a 2 mm panel with a 14 mm gap, and confirm the hole size for the press fit?
A: Send the panel thickness, the gap between the board and the panel, and the LED size on the board. The SUPERB Tech desk picks the pipe length that closes that gap without standing proud.
Why Buy Light Pipes and LED Holders Through SUPERB
- Gap and thickness checked: The order is built from the board to panel gap and the panel thickness, which are the two figures that make an indicator fit.
- Hole size given: The recommended mounting hole is stated per family, so the first panel is cut to the right figure.
- Finish matched to the look: Clear, smoked and diffused bodies are quoted against the panel requirement rather than substituted.
- Board and panel options: A press fit panel pipe and a board mount pipe are both listed, so a sealed case and an open rack are both covered.
- Fitted at the right step: The pipes go in after the panel is located, which keeps them from being pushed back out of the hole during assembly.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Test Points and Spring Contacts for Board Probing, Seven Segment LED Displays for Instrument Readouts, Tactile and Slide Switches for Front Panel Control, Audio Jacks and DC Power Connectors for Instrument Panels, How to Verify a Drop in Replacement.