Contact Us
  • Home
  • COMPONENTS
  • Fan Guards and Filter Screens for Enclosure Cooling

Fan Guards and Filter Screens for Enclosure Cooling

A cooling opening needs two parts: a guard that stops a finger reaching the blades and a filter that stops dust reaching the heat sink. The wire form guards here are C1008 steel with a bright nickel chrome finish, from 40 mm to 120 mm fan size, with mounting hole centres of 32, 50, 71.5, 82.4 and 104.8 mm. The filter assemblies combine a guard, a foam media and a retainer in one part, with media from 30 to 100 pores per inch and a thickness of 4.3 mm to 10.6 mm. Screw pitch is the figure that decides whether a guard fits, because the guard has to line up with the fan holes.
quote now

Product Specifications

Product Overview

An opening in a case is a cooling path and a hazard at the same time. The wire form guard is the part that stops a finger or a tool reaching the blades, and the filter assembly is the part that keeps dust out of the heat sink. They are sold as two families because a cabinet that is cleaned monthly needs a guard, and a cabinet in a workshop needs a guard with a media in front of it.

The Qualtek 08 series guards are formed from C1008 bright basic wire with a bright nickel chrome finish, in fan sizes from 40 mm to 120 mm and beyond. Each size has its own ring and rib wire diameter and its own mounting hole centres: 32 mm for a 40 mm fan, 50 mm for a 60 mm fan, 71.5 mm for an 80 mm fan, 82.4 mm for a 92 mm fan and 104.8 mm for a 120 mm fan. The outside ring diameter is a little larger than the fan, and the thickness is 4.8 mm to 5.66 mm depending on the size.

The 09 series plastic guards are the lower cost alternative for the same openings, moulded in UL94 V-0 material, with a maximum ring spacing of a quarter inch. The same series also carries the filter assemblies, which are a guard, a foam media and a retainer in one stack. Those are the parts used on a cabinet that is in a dusty room, because the media is replaceable without unscrewing the guard.

The media grade is the figure that is almost never on the drawing and almost always the reason a cabinet overheats. A 30 PPI foam passes air easily and stops coarse dust, a 100 PPI foam stops fine dust and costs airflow. On a cabinet with a marginal thermal margin, a 100 PPI media can turn a fan that was adequate into one that is not, and the fix is either a larger opening or a coarser media rather than a bigger fan.

The screw pitch is the second figure. A 92 mm fan and an 80 mm fan are close in size and completely different in hole spacing, and a guard bought by size rather than by pitch will not line up. The screw length also changes, because the guard adds 4.3 mm to 10.6 mm in front of the fan, and a screw that was long enough for the bare fan will not reach the thread with a filter stack in between.

The last point is the finish. A bright nickel chrome on steel is the standard for an indoor cabinet, and a black or stainless version is used where the guard is visible on a product or where corrosion is a factor. On a product that goes to a salt fog test, the plated steel guard is the first part to show a spot, and the stainless version is the answer rather than a thicker plating.

Key Specifications

ParameterValueApplies to
Guard materialC1008 bright basic wireWire form guards, 08 series
Guard finishBright nickel chrome, black, stainless steel08 series
Fan sizes40 mm, 60 mm, 80 mm, 92 mm, 120 mm08 series on this page
Mounting hole centres32 mm, 50 mm, 71.5 mm, 82.4 mm, 104.8 mmBy fan size
Ring diameter1.6 mm to 1.8 mm08 series
Rib diameter1.6 mm to 2.3 mm08 series
Guard thickness4.8 mm to 5.66 mm08 series
Filter assembly contentsGuard, foam media, retainer09 series filter kits
Media grade30, 45, 60, 100 pores per inch09 series filter kits
Filter thickness4.3 mm to 10.6 mm40 mm to 120 mm kits
Plastic guard materialUL94 V-0 moulded plastic09 series
Maximum ring spacing1/4 inch09 series plastic guards

Included Models and Order Codes

The rows below are the guards and filter stacks we quote most often. Fan size and mounting hole centres are given per part because a guard is bought by pitch, and a dash means the maker does not publish that figure.

Part NumberTypeFan SizeHole CentresRing and RibThicknessNotes
08149Wire form guard40 mm32 mm1.6 / 1.6 mm4.8 mmOutside ring 29.5 mm
08147Wire form guard60 mm50 mm1.6 / 1.6 mm4.95 mmOutside ring 53.1 mm
08132Wire form guard80 mm71.5 mm-4.95 mmOutside ring 76.2 mm
08133Wire form guard92 mm82.4 mm1.6 / 1.80 mm4.95 mmOutside ring 89.4 mm
08134Wire form guard92 mm82.5 mm1.6 / 1.80 mm4.95 mmOutside ring 89.8 mm
08130Wire form guard120 mm104.8 mm1.8 / 2.3 mm5.66 mmOutside ring 115.6 mm
08141Wire form guard120 mm104.8 mm1.6 / 2.0 mm5.2 mmOutside ring 117.3 mm
09150-F/100Filter assembly, 100 PPI40 mm32.0 mm-4.30 mmGuard, media and retainer
09250-F/45Filter assembly, 45 PPI60 mm50.0 mm-4.60 mmGuard, media and retainer
09325-F/100Filter assembly, 100 PPI80 mm71.37 mm-9.9 mm83.3 mm wide, 3.81 mm holes
09362-F/60Filter assembly, 60 PPI92 mm82.55 mm-9.9 mm96.5 mm wide
09450-F/100Filter assembly, 100 PPI120 mm104.7 mm-10.6 mm125.2 mm wide, 4.45 mm holes
09450-GGuard only120 mm104.7 mm-7.1 mmPlastic, UL94 V-0

Key Features

Hole centres stated per size – 32, 50, 71.5, 82.4 and 104.8 mm are listed with the fan size, because a guard is bought by pitch and not by the size on the box.

Ring spacing for finger protection – The 09 series guards hold a quarter inch maximum ring spacing, which is the figure a safety review asks for on an accessible opening.

Media grade from 30 to 100 PPI – The foam grade is given per kit, so a cabinet with a thin thermal margin is not fitted with a 100 PPI media that starves the fan.

Guard, media and retainer in one part – A filter kit replaces the media without removing the guard, which is what keeps a maintenance interval realistic.

Thickness for screw length – 4.3 mm to 10.6 mm of added depth is published, because the fan screw has to reach the thread with the stack in place.

Finish options – Bright nickel chrome, black and stainless steel are available, so a visible guard or a salt fog test is not forced onto the plated part.

Applications

These parts are used on any opening that has to pass air and keep a finger or dust out of the case.

Telecom and network cabinets – A 120 mm guard on an outdoor cabinet stops a finger reaching the blades, with the 104.8 mm pitch matching the fan holes already in the sheet metal.

Industrial control panels – A 80 mm filter kit in a workshop keeps coarse dust out of the heat sink, with the 71.37 mm pattern matching the fan on the panel door.

Instrument and lab enclosures – A 40 mm guard on a small enclosure adds 4.8 mm of depth, which is enough for a finger stop without changing the case depth.

The guard adds depth in front of the fan, so the clearance to the SUPERB PCB and to the case wall is checked before the panel is cut. On the SUPERB PCBA route the filter media is fitted last, because a foam that goes through the wash step comes out flattened.

Sourcing and Cross-Reference

A guard is bought by fan size and approved by pitch. When a guard is replaced, the fan size on the label is not enough, because two fans of the same size from different makers can have the same hole pattern and different ring clearances. We ask for the screw pitch measured across the fan and the depth available in front of it, and the guard is chosen from those two figures rather than from the size.

The second point is the media. A cabinet that is cleaned on a schedule can use a coarse media and a guard, and a cabinet in a dusty workshop needs a filter kit with a replaceable media. The grade is chosen against the dust and the thermal margin together, because a finer media that stops more dust also removes airflow, and an overheated cabinet is a worse failure than a dusty one.

The third point is the hardware. A guard adds 4.3 mm to 10.6 mm in front of the fan, and a filter stack adds more, so the original fan screw is usually too short. A screw that is too long will reach the coil or the frame of the fan and stall it. We quote the screw length with the guard where the stack depth is more than the original fan thickness, because that is the mistake that turns a cooling fix into a fan replacement.

SUPERB Assembly checks the guard pattern against the fan holes on the first unit, because a 92 mm guard and an 80 mm guard look alike in a bin and only one of them lines up with the screw holes.

Q: Can you supply a 120 mm wire form guard with a 104.8 mm hole pattern and a 30 PPI filter kit, and confirm the added depth for our fan screws?

A: Send the fan size, the screw pitch and the dust load. The SUPERB Tech desk quotes the guard and the media together, because a 30 PPI foam on a fine dust job clogs in a month and a 100 PPI foam on a hot cabinet starves the fan.

Why Buy Fan Guards and Filters Through SUPERB

  1. Pitch confirmed before the order: The guard is quoted from the measured hole pattern, which is where a 80 mm and a 92 mm guard get mixed.
  2. Media matched to the dust load: The 30 to 100 PPI kits are quoted against the dust and the thermal margin, not against the size of the fan.
  3. Depth stated for the screws: The added thickness is published, so the fan screw is long enough to reach the thread and short enough not to touch the blades.
  4. Guard and media in one kit: The media is replaced without removing the guard, which keeps a maintenance interval realistic on a panel door.
  5. Finish for the environment: Plated steel, black and stainless versions are available, so a visible guard or a salt fog test is not forced onto one finish.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Rubber Bumpers and Feet for Enclosure Support, EMI Shielding Cans and Contact Gaskets for RF Boards, Standoffs Spacers and Mounting Hardware for Board Stacks, Cable Glands and Strain Relief Bushings for Enclosure Entries, How to Verify a Drop in Replacement.