IEC 60601 Power Supplies for Medical Diagnostic Equipment A medical supply is chosen on leakage current and isolation before it is chosen on watts. The 65 to 300 W open frame family carries 2xMOPP between primary and secondary, with 4 kVAC isolation. Earth leakage runs from 130 to 190 uA depending on series, and touch current from 40 to 100 uA. All of them accept 80 to 264 VAC and run from minus 30 to plus 70 C, with a 3 year warranty.
Wireless Charging Receiver and Transmitter ICs A Qi link is built from a transmitter that drives a coil and a receiver that rectifies what the coil picks up, and the two ends are separate part numbers. The receiver sets the output rail and the thermal budget in the product; the transmitter sets the input rail, the coil current and the foreign object detection. The table below gives output power, rectified voltage, protocol version and package for the codes we quote most often.
Isolated Gate Drivers and SiC Gate Drive Supplies Isolated drivers break the gate loop from the control ground, so a high side switch can be driven without a bootstrap that runs out at high duty cycle. Single channel parts carry desaturation detection and a Miller clamp for IGBT and SiC turn off. Dual channel parts cover half bridge, dual high side and dual low side from one package with programmable dead time. Each row lists isolation rating, peak current, delay and UVLO, because those set the gate resistor and the layout of the barrier.
IS6607A IS6607A: 20 A synchronous buck regulator, 0.6 V reference, QFN. Original parts with traceability, small quantities and fast quotes from SUPERB.
MP8759GD MP8759GD: 26 V, 8 A synchronous step-down converter, QFN. Original parts with traceability, small quantities and fast quotes from SUPERB.
Charge Pump Regulators and Inverting Converters Switched capacitor inverters, doublers and regulated charge pumps from 1.6 V to 38 V input. Output current runs from 10 mA on the smallest parts to 250 mA on the regulated dual output parts. Oscillator frequency and package are listed per row, with the regulation method named. Parts that keep the ICL7660 pinout are marked, because that footprint still appears on old boards.
Boost and SEPIC Converter Controllers for Wide Input Rails Boost, SEPIC and flyback controllers with input ranges from 2.9 V to 100 V. Synchronous and non-synchronous gate drive options are listed with the peak driver current. Switching frequency, current limit and soft start are set by external parts on every row. Controllers are quoted with the external MOSFET and the sense resistor for a complete stage.
PFC Controllers for AC-DC Front Ends Active power factor controllers for boost stages in AC-DC front ends. Continuous conduction mode parts hold a fixed frequency from 18 kHz to 250 kHz. Critical conduction mode parts cover adapters and ballasts up to about 350 W. Average current control, brown out detection and open loop protection on chip.
Battery Protection ICs and BMS Analog Front Ends Protection and monitoring devices for lithium packs from one cell to eighteen cells in series. Cell measurement of 5 mV at 25 degrees on the BQ76952, with coulomb counting on the same die. Single cell protectors add overcharge, overdischarge and short circuit cut off in a 1.5 mm package. isoSPI and I2C interfaces for packs that stack several monitors.
Power over Ethernet PD Controllers for Powered Devices PD interface controllers for IEEE 802.3af, 802.3at and 802.3bt powered devices. PD power from 13 W on type 1 up to 71.3 W on class 8, with 5 event classification. Integrated hotswap FETs from 0.3 ohm, or external FETs for the highest efficiency. Flyback, forward and buck converter controllers on the same die as the interface.
Constant Current LED Driver ICs for Indicator and Backlight Boost, buck and linear constant current topologies for LED strings. Output current from 10 mA on a linear regulator up to 5 A on a buck controller. PWM dimming ratios to 10,000 to 1 and analog dimming for camera-safe light. Single channel drivers and 24 channel serial sinks in one supply line.
Supervisory and Watchdog Timer ICs for MCU and FPGA Rails Reset supervisors with fixed and adjustable thresholds from 0.4 V to 5 V. Watchdog timers with window and standard timeout behaviour. Threshold accuracy from 0.5 to 2.5 percent over temperature. Manual reset inputs, power good outputs and open drain or push pull reset.
Load Switches and Hot Swap Controllers for Board Power Sequencing Integrated load switches from 1 V to 5.5 V and 1.5 A to 6 A. On resistance from 16 milliohm to 90 milliohm with quiescent current in microamps. Hot swap controllers from 2.9 V to 80 V with programmable current limit and fault timer. Adjustable slew rate, reverse current blocking and power good outputs.
Isolated DC-DC Modules and Brick Converters for Instrument Boards Encapsulated modules from 1 W to 20 W in SIP, DIP, SMD and 1 x 1 inch footprints. Isolation from 1 kVDC to 5.2 kVDC, single and dual outputs. Wide 2 to 1 and 4 to 1 input ranges for 12 V, 24 V and 48 V rails. Brick converters for higher power floating and intermediate bus rails.
Battery Chargers and Fuel Gauges for Portable Instruments Linear chargers from 500 mA to 1.5 A with power path and input current limit. Switch mode chargers up to 5 A with I2C control and 93 percent efficiency. Fuel gauges using voltage model or coulomb counting, with and without a sense resistor. Protection, termination and status outputs in SOT-23, QFN and SON packages.
BLDC and Stepper Motor Driver ICs for Motion Control Three phase gate drivers for 6 V to 60 V motor stages with external FETs Integrated FET drivers with 2.5 A half bridge capability and on board LDO Sensorless and sensored trapezoidal drivers that need no control firmware Stepper and dual DC motor drivers for positioning stages
PWM Controller ICs for Switching Power Supplies Current mode controllers in eight pins, up to 500 kHz with pulse by pulse limiting Push pull and half bridge controllers with adjustable dead time and soft start PFC front end controllers for EN61000-3-2 compliant supplies above 350 W All models on this page are grouped into one part for easy sourcing
LDO Linear Regulators for Low Noise Power Rails Ultralow noise LDOs from 0.8 uV rms for RF and instrumentation rails High voltage parts up to 36 V input for industrial and telecom boards Fixed and adjustable outputs from 150 mA to 1.5 A load current All models on this page are grouped into one part for easy sourcing
ADI Power Management ICs for Optical Modules and Instrument Boards Low noise power parts for optical module and instrument board rails Low Vin and 20 V low noise LDOs, configurable synchronous bucks, a buck plus LDO micro PMU All models listed below are combined into this single product for easy sourcing Samples, build quantities, alternatives and cross reference are supported
Step-Down DC-DC Converter Chips for Industrial Power Rails Texas Instruments step-down buck converter chips and MicroSiP modules for industrial power rails 1 A to 3 A output from 3 V to 36 V inputs, with fixed and adjustable output versions All models listed below are combined into this single product for easy sourcing Samples, build quantities, alternatives and cross reference are supported
ADI TEC Controller Chips for Optical Module Temperature Control ADI thermoelectric cooler controller chips for the temperature control loop of optical modules Covers 1 A to 6 A TEC drive for cooled SFP+, DWDM, EDFA pump laser and tunable laser designs All models listed below are combined into this single product for easy sourcing Samples, volume orders, alternatives and cross reference are supported
MC33PF8100EAES The MC33PF8100EAES is NXP's 12-channel power management IC (PMIC) purpose-built for high-performance processing applications. Integrating 7 buck regulators and 4 LDOs, it delivers complete power management for NXP i.MX8 and S32x application processors from a single 5V input. OTP pre-programmed with the exact voltage levels, power-up sequencing, and fault handling required by the target processor, it eliminates external sequencing and simplifies board design. AEC-Q100 automotive qualification, -40C to +125C operation, and the compact QFN-56 package make it the definitive power solution for automotive infotainment, digital clusters, telematics, vehicle networking, ADAS, and vision/sensor fusion systems.
LTC7150SEY#PBF The LTC7150SEY#PBF is Analog Devices' 20V, 20A synchronous step-down DC-DC regulator featuring second-generation Silent Switcher 2 technology. It integrates the hot-loop bypass capacitors inside the package to minimize EMI radiation, enabling clean, compact high-current power delivery without complex external filtering. Accepting 3.1V to 20V input with 0.6V to 5.5V adjustable output, programmable switching from 400kHz to 3MHz, current-mode control, and integrated power MOSFETs, it is the definitive high-current point-of-load solution for FPGA/ASIC core rails, server processors, and high-density computing power supplies. The BGA-42 package delivers low thermal resistance and short internal connections for exceptional power density.
L78L05ACUTR L78L05ACUTR is a linear voltage regulator from STMicroelectronics, designed for drone power distribution boards, BEC circuits, and battery voltage regulation. Superb Automation supplies genuine L78L05ACUTR with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
L6599DTR L6599DTR is a switching regulator IC from STMicroelectronics, designed for drone power distribution boards, BEC circuits, and battery voltage regulation. Superb Automation supplies genuine L6599DTR with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
L99MC6TR L99MC6TR is a motor driver IC from STMicroelectronics, designed for drone motor control, ESC gate drivers, and robotic actuator control. Superb Automation supplies genuine L99MC6TR with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
L78L12ACUTR L78L12ACUTR is a linear voltage regulator from STMicroelectronics, designed for drone power distribution boards, BEC circuits, and battery voltage regulation. Superb Automation supplies genuine L78L12ACUTR with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
VND7E025AJTR VND7E025AJTR is a motor driver IC from STMicroelectronics, designed for drone motor control, ESC gate drivers, and robotic actuator control. Superb Automation supplies genuine VND7E025AJTR with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
VND7NV04TR-E VND7NV04TR-E is a motor driver IC from STMicroelectronics, designed for drone motor control, ESC gate drivers, and robotic actuator control. Superb Automation supplies genuine VND7NV04TR-E with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
L78L33ABUTR L78L33ABUTR is a linear voltage regulator from STMicroelectronics, designed for drone power distribution boards, BEC circuits, and battery voltage regulation. Superb Automation supplies genuine L78L33ABUTR with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
VIPER12ADIP-E VIPER12ADIP-E is a switching regulator IC from STMicroelectronics, designed for drone power distribution boards, BEC circuits, and battery voltage regulation. Superb Automation supplies genuine VIPER12ADIP-E with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
L6206PD013TR L6206PD013TR is a motor driver IC from STMicroelectronics, designed for drone motor control, ESC gate drivers, and robotic actuator control. Superb Automation supplies genuine L6206PD013TR with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
VN7140ASTR VN7140ASTR is a motor driver IC from STMicroelectronics, designed for drone motor control, ESC gate drivers, and robotic actuator control. Superb Automation supplies genuine VN7140ASTR with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
STSPIN32G4 STSPIN32G4 is a motor driver IC from STMicroelectronics, designed for drone motor control, ESC gate drivers, and robotic actuator control. Superb Automation supplies genuine STSPIN32G4 with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
L6920DTR L6920DTR is a switching regulator IC from STMicroelectronics, designed for drone power distribution boards, BEC circuits, and battery voltage regulation. Superb Automation supplies genuine L6920DTR with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
ST1S14PHR ST1S14PHR is a switching regulator IC from STMicroelectronics, designed for drone power distribution boards, BEC circuits, and battery voltage regulation. Superb Automation supplies genuine ST1S14PHR with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
VNQ7050AJTR VNQ7050AJTR is a motor driver IC from STMicroelectronics, designed for drone motor control, ESC gate drivers, and robotic actuator control. Superb Automation supplies genuine VNQ7050AJTR with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
VIPER26HDTR VIPER26HDTR is a switching regulator IC from STMicroelectronics, designed for drone power distribution boards, BEC circuits, and battery voltage regulation. Superb Automation supplies genuine VIPER26HDTR with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
VND5T100AJTR-E VND5T100AJTR-E is a motor driver IC from STMicroelectronics, designed for drone motor control, ESC gate drivers, and robotic actuator control. Superb Automation supplies genuine VND5T100AJTR-E with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.
VNH3SP30TR-E VNH3SP30TR-E is a motor driver IC from STMicroelectronics, designed for drone motor control, ESC gate drivers, and robotic actuator control. Superb Automation supplies genuine VNH3SP30TR-E with full traceability, competitive pricing, and fast global delivery — supporting prototype to production volumes for drone, robotics, and industrial customers worldwide.