Contact Us
  • Home
  • COMPONENTS
  • Trimmer Potentiometers for Calibration and Bias Setting

Trimmer Potentiometers for Calibration and Bias Setting

A trimmer is picked on turns, power rating and sealing, because the electrical load is small and the setting has to survive wash and life. The parts here run from a single turn 3/8 inch body to a 25 turn lead screw type, at 0.25 W to 0.75 W. Power derates to zero at the top of the temperature range on every series, so the rating at 70 C is the figure that matters. Each row lists turns, power, temperature coefficient and mounting.
quote now

Product Specifications

Product Overview

A trimmer is a potentiometer that is set once, on the bench or at first calibration, and then left alone. That single fact decides most of the specification. The wiper is not expected to move thousands of times, so rotational life is quoted at 200 cycles rather than at the millions of a panel control. What matters instead is that the setting does not drift: contact resistance variation, temperature coefficient and the sealing that keeps flux and wash water out of the element are the three figures that decide whether a board still meets its calibration a year later.

Turns set the resolution. A single turn 3/8 inch body such as the 3386P spreads the full resistance over about 270 degrees, which is enough for a coarse bias set but not for a 1 mV offset on a 10 V rail. The 25 turn 3296W moves the wiper along a lead screw, so one turn of the screw changes the resistance by about 4 percent of the total and a 10 kOhm part can be set in steps of about 400 Ohm per turn. That is why the multi turn parts dominate on amplifier offset, reference trim and laser bias, where a small change at the wiper is a large change at the output.

Power rating is quoted at a case temperature, not at room temperature for ever. The 3296 is 0.5 W at 70 C and derates linearly to 0 W at 125 C. The 3266 is 0.25 W at 70 C with the same slope, and the 3214 and 3224 are 0.25 W at 85 C with a range to 150 C. A trimmer used as a voltage divider carries current through the whole element and the wiper, so the element power is V squared over R and has to be checked at the highest ambient in the enclosure, not at the bench.

Temperature coefficient is the second source of drift. The cermet parts here are 100 ppm per C, which on a 10 kOhm setting is 1 Ohm per C, and the effect on a divider is a shift in ratio only where the two halves do not track. A 25 turn part does not have a better coefficient than a single turn part of the same family, but it lets the setting be placed closer to the target, so the residual error that the coefficient acts on is smaller.

Sealing decides the process. The 3296 series is sealed and rated IP65, and the 3214 and 3224 are sealed to withstand board wash. A sealed part can go through aqueous cleaning with the rest of the board; an unsealed one takes water into the element and reads high resistance until it dries, or permanently if the wash leaves residue. The Vishay T93 series is rated IP67 and is the part to reach for on a conformal coated board, where the coating has to key to a smooth body.

Two mistakes repeat. A trimmer is sometimes used as a two terminal variable resistor in a path that carries tens of milliamps, which puts the wiper contact at its current limit and shows up as noise after a few months; the wiper is meant for the high impedance side of a divider or an amplifier input. And a setting made before washing is not a setting: the screw moves when the board is cleaned, so the value is set after the wash and marked.

Key Specifications

ParameterValueApplies to
Number of turns1, 5, 12, 15, 25Per part number
Power rating0.25 W, 0.5 W, 0.75 WPer part number
Resistance10 kOhm on the parts listed, families from 10 Ohm to 2 MOhmPer part number
Toleranceplus or minus 10 percentAll parts listed
Temperature coefficientplus or minus 100 ppm per C, 150 ppm on the PV rangePer part number
ElementCermet, linear taperAll parts listed
Rotational life200 cyclesBourns series listed
Contact resistance variation1 to 3 percent, or 3 Ohm, whichever is greaterPer series
Operating temperature-55 to 125 C, -65 to 150 C on the 4 mm SMD partsPer part number
SealingIP65 on the 3296, IP67 on the T93, sealed for board wash on the 4 mm partsPer part number
Dielectric strength600 VAC at sea level on the 4 mm parts, 900 VAC on the 3296Per part number
MountingThrough hole top or side adjust, SMD J-leadPer part number
Body size4 mm, 1/4 inch, 3/8 inch, 19 mmPer part number

Included Models and Order Codes

The rows below are the 10 kOhm parts we quote most often, in the footprint each board actually uses. The resistance code is the same on all of them, so the choice is turns, size and mounting rather than value. A dash means the maker does not publish that figure for the part.

Part NumberTurnsPowerSize and MountTCRSealing and Notes
3296W-1-103LF250.5 W at 70 C3/8 inch square, through hole, top adjust100 ppm per CIP65, 900 VAC dielectric, 200 cycles
3266W-1-103LF120.25 W at 70 C1/4 inch square, through hole, top adjust100 ppm per CSealed, 200 cycles
3269W-1-103LF120.25 W at 70 C1/4 inch square, SMD J-lead100 ppm per CSealed, pick and place body
3224W-1-103E120.25 W at 85 C4 mm square, SMD J-lead100 ppm per CSealed for board wash, -65 to 150 C
3223W-1-103E110.125 W at 85 C4 mm square, SMD J-lead100 ppm per CSealed, low profile body
3214W-1-103E50.25 W at 85 C4 mm square, SMD J-lead100 ppm per CSealed for board wash, 600 VAC dielectric
3386P-1-103LF10.5 W at 70 C3/8 inch square, through hole, top adjust100 ppm per CSingle turn, coarse set
3006P-1-103LF150.75 W at 70 C19 mm, through hole, side adjust100 ppm per CLargest body, highest power in the list
T93YA103KT2019 plus or minus 20.5 W at 70 C3/8 inch square, through hole100 ppm per CIP67, 250 V working, 1.5 Ncm torque

Key Features

Turns stated per part – Single turn, 5, 11, 12, 15 and 25 turn parts are listed, so the resolution needed for an offset trim is visible before the order.

Power derating given – The rating at 70 C or 85 C and the point where it falls to zero are both listed, because the bench figure is not the enclosure figure.

Sealing class per part – IP65, IP67 and sealed for board wash are named, so a part can be picked for a board that is washed or coated.

One footprint, several turns – The 4 mm SMD footprint appears in 5, 11 and 12 turn versions, so a setting can be changed without a board change.

Cermet element – The cermet track holds its value through reflow and wash better than a carbon track, at 100 ppm per C.

SMD and through hole – J-lead SMD parts for automated lines and pinned parts for hand set boards are both in the list.

Applications

These parts cover the adjustments that are made once and then checked at test: offset, bias, reference level and gain.

Amplifier offset and bias – A 25 turn 3296W sets an input offset to a few microvolts on an instrumentation amplifier, where a single turn part cannot be placed close enough to the target.

Reference and supply trim – A 4 mm SMD part trims a reference divider on a board that is washed after reflow, and its 0.25 W rating covers the divider current at the top of the enclosure temperature.

Instrument calibration – A 19 mm 3006P at 0.75 W is used where the trimmer carries the whole divider current, and its side adjust screw is reached through a panel hole.

Trimmers are set on the SUPERB PCB and checked again after the SUPERB PCBA wash, so the sealing class of the part matters as much as the resistance value.

Sourcing and Cross-Reference

Trimmers are ordered by value and footprint, and the two are usually both wrong when a board is copied from an older build. The resistance code 103 means 10 kOhm in every series here, but the body size and the pin pitch are not shared, so a 3296 footprint does not accept a 3266 part. We ask for the footprint drawing or the old part number and quote the nearest series that fits it.

Obsolete trimmers are common because the bodies change and the values do not. Where a series has gone, the same turns and the same footprint are usually still made by another maker, and the setting procedure carries over unchanged. Where the footprint has gone as well, we quote the nearest size and state the pin positions, so the board change is known before the order.

Settings are part of the supply where the customer wants it. A trimmer can be supplied preset to a value and marked, which removes one adjustment from the test step, and it is the arrangement we use most often on boards that are built in volume and calibrated in a fixture.

SUPERB Assembly sets each trimmer to the value on the test sheet and marks the screw, which is the only way to see afterwards that a setting has moved.

Q: Can you supply a trimmer that fits an existing footprint but gives finer resolution than the part we use now?

A: Turns, power rating and sealing decide it; the SUPERB Tech desk quotes the same footprint in single turn and multi turn so a setting can be changed without a board change.

Why Buy Trimmer Potentiometers Through SUPERB

  1. Footprint first: The old part or the footprint drawing is checked before a series is quoted, so the replacement fits the board.
  2. Resolution matched: Turns are quoted against the adjustment the circuit needs, not against the cheapest part in the value.
  3. Sealing stated: The wash and coating process decides between an IP65, IP67 and sealed part, and the class is named on every row.
  4. Preset option: Trimmers can be supplied set and marked, which removes an adjustment from the test step.
  5. Same house as the board: The part is placed and set in the same build as the board, so a setting that moves after wash is caught at test.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Resistor Arrays and Precision Thin Film Resistors, MLCC and Ceramic Capacitors, Instrumentation Amplifiers, DACs and Voltage References, Pin to Pin Cross Reference.