Contact Us
  • Home
  • COMPONENTS
  • Jumper Links and Shunt Headers for Board Configuration

Jumper Links and Shunt Headers for Board Configuration

A jumper link is the cheapest way to make one board serve two builds, and the cheapest way to lose a contact if the wrong shunt is used.\nThe 2.54 mm shunts here carry 3 A at 250 VAC with 20 mOhm maximum contact resistance and a 25 mating cycle rating.\nOpen top, grip and test point versions are listed, in heights of 5.97 mm and 13.75 mm, from 2 to 16 positions.\nThe Samtec shunt in the same table is rated 4.3 A per contact, for boards that draw more than the standard part allows.
quote now

Product Specifications

Product Overview

A shunt is a two pin socket that shorts two adjacent header pins. It is used to select an option at build time, to join two ground planes, to enable a termination or to bypass a stage during test. It costs less than any switch and it needs no tool, which is why it survives on boards that are otherwise fully programmed. The part itself is simple: a PBT body, two gold plated copper alloy contacts, and an open top that lets a probe touch the contact while the link is fitted.

The 2.54 mm parts on this page are the Wurth WR-PHD jumper family. The standard open top part is 5.97 mm high, rated 3 A at 250 VAC, with 20 mOhm maximum contact resistance, 1000 mOhm minimum insulation resistance and a 500 VAC withstand for one minute. The body is PBT with a UL94 V-0 rating, and the operating range is -40 to +125 C. The same family is offered in black, red and blue, with a test point on top, and in a taller grip version that is 13.75 mm high and can be pulled off with fingers instead of a tool.

The multi position version puts several shunts in one body: a 2 by 8 part covers sixteen pins in a single moulding. That is used where a whole block of links has to be set the same way, for example a set of address or option links that are all fitted or all removed. It saves placement time and it removes the chance of fitting fifteen of sixteen links.

The Samtec SNT-100-BK-G is the part to use when the current is higher than the standard 3 A. It is a 2.54 mm open top shunt with gold flash contacts, rated 4.3 A per contact, and it uses phosphor bronze contacts rather than the copper alloy of the Wurth part. It fits the same 2.54 mm header, so the choice between the two is a current and cost decision, not a footprint decision.

There is one habit worth naming. A shunt that has been fitted and removed several times loses contact tension, and the failure shows up as an intermittent link on a board that has passed test. The mating cycle rating of the standard part is 25 cycles, which is enough for the line and for a few service changes, but not enough for a link that is moved every time the board is configured. Where a link has to be changed often, a DIP switch or a 0 Ohm link is the better answer, and we say so before quoting the shunt.

Key Specifications

ParameterValueApplies to
Pitch2.54 mmWR-PHD jumper family
Positions2 positions (1 x 2) up to 16 positions (2 x 8)Per part number
Rated current3 AWR-PHD jumper family
Rated current per contact4.3 ASamtec SNT-100-BK-G
Working voltage250 VACWR-PHD jumper family
Withstanding voltage500 VAC for 1 minuteWR-PHD jumper family
Contact resistance20 mOhm maximumWR-PHD jumper family
Insulation resistance1000 mOhm minimumWR-PHD jumper family
Durability25 mating cyclesWR-PHD jumper family
HousingPBT, UL94 V-0, open topWR-PHD jumper family
Contact materialCopper alloy, gold plated, stampedWR-PHD jumper family
Height5.97 mm standard, 13.75 mm on the grip versionWR-PHD jumper family
Operating temperature-40 to +125 CWR-PHD jumper family
Header compatibility2.54 mm pin headers with 0.64 mm square pinsAll parts on this page

Included Models and Order Codes

The rows below are the shunt bodies and the headers they are used with. The header rows are breakaway strips, so a 2 pin link can be cut from a longer strip; the price and the packing follow the full strip. A dash means the maker does not publish that figure.

Part NumberPositionsTypeHeightRatingNotes
609002134212 (1 x 2)Open top with test point, black5.97 mm3 A, 250 VACStandard part, gold contacts, bag
609002135212 (1 x 2)Open top with test point, red5.97 mm3 A, 250 VACColour coding for a supply link
609002136212 (1 x 2)Open top with test point, blue5.97 mm3 A, 250 VACColour coding for a signal link
6090021151212 (1 x 2)Open top with grip, black13.75 mm3 A, 250 VACTall body, removed by finger
6091081342116 (2 x 8)Open top, black5.97 mm3 A, 250 VACEight links in one body
SNT-100-BK-G2 (1 x 2)Open top, black-4.3 A per contactPhosphor bronze, gold flash, 2.54 mm
TSW-102-07-G-S2Pin header, straight2.54 mm pinPer header ratingThe header a shunt sits on, breakaway strip
TSW-110-07-G-D10 (2 x 5)Pin header, straight, dual row2.54 mm pinPer header ratingDual row strip for a 2 x 8 link block

Key Features

Probeable while fitted – The open top leaves the contact visible, so a meter can touch the link without removing it, which is what makes the test point version useful during bring up.

Gold on the contact – Both the Wurth and the Samtec parts use gold on the contact surface, so a low current link does not depend on a tinned surface that oxidises in storage.

Two current classes – The standard 3 A part and the 4.3 A Samtec part share the 2.54 mm footprint, so a board that draws more current does not need a different header.

Grip version for service – The 13.75 mm grip body can be pulled by finger, which keeps a service engineer from levering a small shunt off with a screwdriver and damaging the header.

Multi position block – A 2 by 8 body sets sixteen pins in one placement, removing the chance of fitting fifteen links and leaving one open.

Stated mating life – The 25 cycle rating is given up front, so a link that is moved at every configuration is recognised as a switch job rather than a shunt job.

Applications

These links are used where an option has to be set at build time and changed rarely afterwards.

Option and build selection – A 2 or 3 pin link selects a firmware variant, a supply range or an output mode, so one board can be built for two customers without two part numbers.

Ground joining and shielding – A link joins an analogue ground to a digital ground at one point, which is the usual way to keep a single point connection that can be opened for a noise test.

Termination and bias – A link fits or removes a bus termination resistor on a backplane card, so the same card works in the middle or at the end of the line.

The shunt and the header it sits on are placed on the SUPERB PCB as a pair, and the SUPERB PCBA build sheet states which links are fitted at the line and which are left in the bag for the customer to fit.

Sourcing and Cross-Reference

Shunts are a commodity part, and the usual problem is not availability but the header underneath. A shunt is quoted against a 2.54 mm header with 0.64 mm square pins, and a header with round pins or a different pin length will hold the shunt at the wrong height or not at all. We ask for the header part number, not only the shunt, and we quote the pair when the board is being built.

The second problem is contact tension after rework. A shunt that has been removed and refitted a few times can pass a continuity test and still fail a vibration test. Where the link is part of the product configuration rather than a build option, we recommend a DIP switch or a soldered link, and we say so rather than supply a part that will come back.

Colour is not cosmetic on these parts. A red shunt on a supply link and a black shunt on a signal link is a convention that survives service, and it is the reason the same body is offered in several colours. When a customer asks for a colour that is not in the standard range, that is a special order, and the lead time is longer than the standard part.

SUPERB Assembly keeps the shunts in their original bags until the board is tested, because a shunt that has been pushed onto a header and pulled off again loses contact tension and no longer holds its position.

Q: Can you supply the shunt and the 2.54 mm header as a matched pair, and confirm the current rating for our link?

A: Send the header pitch, the number of links and whether the link has to be probeable. The SUPERB Tech desk quotes the shunt and the header together so the two arrive as a matched pair.

Why Buy Jumper Links Through SUPERB

  1. Header and shunt quoted together: The link is only as good as the pin it sits on, so the header part number is checked before the shunt is quoted.
  2. Current class stated: The 3 A standard part and the 4.3 A Samtec part are listed with their own ratings, so a supply link is not quoted a signal part.
  3. Mating life given: The 25 cycle figure is stated, which makes it clear when a link should be a switch instead.
  4. Colour kept consistent: Standard colours are held for supply, signal and test links, so a service engineer reads the board the same way the build sheet does.
  5. Fitted or bagged, as agreed: The build sheet states which links are fitted at the line and which travel in the bag, so nothing is lost between assembly and test.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Pin Headers and Female Sockets for 2.54 mm Board Stacking, Test Points and Spring Contacts for Board Probing, DIP Switches and Rotary Address Switches for Configuration, Wire to Board Crimp Housings and Headers for Harness Builds, Passive Component Cross Reference.