Contact Us
  • Home
  • COMPONENTS
  • Pin Headers and Female Sockets for 2.54 mm Board Stacking

Pin Headers and Female Sockets for 2.54 mm Board Stacking

A 2.54 mm header is chosen on the number of ways, the mating length and the plating, because the pitch is fixed by the standard. The male strips on this page carry 3 to 6.3 A and run at 250 to 550 V depending on the maker and the way count. Female sockets add the mating half for board stacking, in Tiger Buy contact form with a square tail. Tin and gold plating are both listed, since the finish decides the insertion life and the cost.
quote now

Product Specifications

Product Overview

The 2.54 mm header is the oldest connector on the board and still the one that causes the most assembly questions. The pitch is fixed, so the choices are the number of ways, the row count, the post length and the plating. A 0.635 mm square post is the standard contact, and the lengths are quoted as mating length, post length below the insulator and overall length, because a part that is right in one dimension can be wrong in another.

Two parts make a stack. The male strip is soldered to one board and the female socket to the other, and the mating length decides how far the pair can be separated. A 5.84 mm mating length with a 2.54 mm post gives a 10.92 mm overall length on the Samtec TSW part, which is what a 2.54 mm insulator height and a 0.1 inch stack are built around. If the stack height changes, the post length changes and the part number changes with it.

Plating is the cost and life decision. Tin is the standard finish for a connector that is mated once at assembly, and gold is used where the joint is separated for service or where a low and stable contact resistance is needed. Gold at 10 micro inches on the mating area with gold flash on the tail is the usual middle ground. Molex KK parts are tin over brass at 4 A, and the Samtec strips are gold over phosphor bronze at 3 to 6.3 A depending on the way count.

Key Specifications

ParameterValueApplies to
Pitch2.54 mmAll parts on this page
Contact0.635 mm square postMale headers
Ways2 to 20 per rowPer part number
RowsSingle, dualPer part number
Current3 A to 6.3 A per contactPer part number
Voltage250 VAC to 550 VACPer part number
Mating length5.84 mm on TSW seriesTSW parts
Post length2.54 mm below the insulator on TSWTSW parts
PlatingGold 10 micro inch, or tinPer part number
InsulatorPBT or LCP, UL 94 V-0Per part number
Operating temperature-55 to 125 C on Samtec, -40 to 105 C on WurthPer part number
Mating cycles25 on Molex KK, higher on gold plated stripsPer part number

Included Models and Order Codes

The rows below are the 2.54 mm strips and sockets we quote most for board stacking and cable headers. Mating length and post length are given where the maker publishes them, because those set the stack height. Current is per contact at the way count tested, not a single figure for the whole connector.

Part NumberTypeWaysRatingNotes
TSW-102-07-G-SPin header, single row, through hole2Up to 6.3 A, 550 VAC0.635 mm square post, 5.84 mm mating, 10.92 mm overall, gold 10 micro inch
TSW-110-07-G-DPin header, dual row, through hole20 (10 per row)Up to 6.3 A, 550 VACSame post and plating as the single row part
SSQ-110-01-G-SSocket strip, single row10465 VAC, 655 VDCTiger Buy contact, LCP insulator, gold over phosphor bronze
SSW-110-01-G-SSocket strip, single row, solder tail10Per maker curve0.104 inch tail, up to 8 Gbps, through hole
61300211121Pin header, single row, vertical23 A, 250 VAC20 m ohm, 500 V withstanding, -40 to 105 C
22032021Pin header, KK 254, single row24 A, 500 VTin over brass, 25 mating cycles, stackable, 3.43 mm tail

Key Features

Pitch and post standard – The 0.635 mm square post and the 2.54 mm pitch are stated so the part is matched to the existing footprint.

Stack height from lengths – Mating length, post length and overall length are given, which is what sets a board to board distance.

Current per contact – 4 A on the KK part and up to 6.3 A on the gold strips are quoted per contact, not for the whole connector.

Plating and cycles together – Tin at 25 cycles and gold at higher life are listed with the finish, so the choice follows the number of matings.

Male and female on one page – Headers and sockets are quoted together, so a stacking pair is not ordered from two sources with different plating.

Insulator material stated – PBT and LCP are named, which decides whether the part survives a reflow profile as well as wave solder.

Applications

These parts are used for board stacking, programming headers, cable interfaces and module connectors.

Board to board stacking – A 10.92 mm overall header mated with a 10 way socket sets a fixed stack height, and the socket tail length is chosen to match the lower board thickness.

Programming and debug headers – A 2 way gold strip takes a pogo fixture or a cable once at production, and the gold finish keeps the contact clean after storage.

Cable and module interfaces – A KK 254 header at 4 A carries a wire harness to a board, and the tin finish suits a joint that is mated once and left.

The header is soldered to the SUPERB PCB, and the socket is fitted to the mating board so the pair is checked as a stack on the SUPERB PCBA.

Sourcing and Cross-Reference

Headers are quoted on ways, rows, post length and plating, and the post length is the one that decides whether a stack closes. A customer who asks for a 2.54 mm header usually has the footprint right and the height wrong, so we ask for the stack height and the board thickness, then pick the mating and post lengths that produce it.

Plating is the second decision. Tin is cheaper and adequate for a joint mated once, while gold is used where the header is separated for service or where the contact resistance has to stay low after storage. Mixing a gold header with a tin socket is possible and is sometimes done, but it is a decision to make on purpose rather than by accident, so both halves are quoted together.

SUPERB Assembly measures the stack height after the first mating and confirms the post does not bottom out in the socket before the batch runs.

Q: Can you supply a header and socket pair that keeps our existing 2.54 mm footprint and stack height?

A: SUPERB Tech quotes the strip with the socket that mates with it, so the plating and the contact length are decided once for both halves.

Why Buy 2.54 mm Headers Through SUPERB

  1. Stack height worked out: Mating and post lengths are matched to the board thickness, so the pair closes at the height the drawing asks for.
  2. Pairs quoted together: Header and socket come from one quote with the same plating, so the joint is not mismatched.
  3. Current per contact: The rating is given for the way count tested, not as a headline figure for the connector.
  4. Plating on the record: The finish is written on the order, so a repeat build gets the same insertion life.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Board to Board and FPC Connectors, Test Points and Spring Contacts, Screw Terminal Blocks and Pluggable Connectors, BOM Cost Optimization Guide.