Contact Us
  • Home
  • COMPONENTS
  • USB Type-C and USB A Receptacles for Power and Data Ports

USB Type-C and USB A Receptacles for Power and Data Ports

A USB port is decided by three numbers: the tab length against the board thickness, the current rating against the cable, and the mating cycles against how often the port is used.\\nThe Type-C parts here carry 24 contacts on a 0.5 mm pitch, rated 5 A at 48 V DC and 10,000 mating cycles.\\nThe Type-A parts carry 4 contacts on a 2 mm pitch, rated 1 A or 1.5 A per contact and 1,500 mating cycles.\\nSolder tab length runs from 0.60 mm to 1.30 mm, and that range covers boards from 0.80 mm to 1.60 mm.
quote now

Product Specifications

Product Overview

This page covers the connector body of a USB port: the receptacle that is soldered to the board and takes the plug. The Type-C parts are one 24 contact shell in two rows on a 0.5 mm pitch, reversible, with a metal shell that has four through hole tabs for retention and surface mount tails for the signal contacts. The Type-A parts are the older 4 contact body on a 2 mm pitch, right angle or vertical, with two kinked legs that hold the shell to the board.

A Type-C receptacle is not a power supply. The 5 A and 48 V figures in the tables below are the rating of the contacts and the shell, and the power a port actually delivers is set by the cable, the plug and the controller behind it. On a board that has no power delivery controller, the receptacle is a 5 V port with a data link, which is what most instrument panels use it for. The page that covers the controllers is linked at the bottom of this one.

The Molex 105450 series is the part we quote most often for a Type-C port. It has 24 contacts, 10,000 mating cycles, an operating range of -30 to +85 C, and a gold flash of 0.051 micrometre over 0.762 micrometre of palladium nickel on the contacts. The three order codes in the table differ in solder tab length: 0.60 mm, 0.80 mm and 1.30 mm, and the 1.30 mm part is the one that reaches through a 0.80 mm or a 1.00 mm board.

The Wurth 632723300011 is the same 24 contact body with a different termination: hybrid, with through hole reflow tabs and surface mount tails in one footprint. It is rated 5 A at 48 V DC, with a contact resistance of 30 mOhm or less and an operating range of -40 to +105 C. The hybrid footprint is the reason to choose it, because the through hole tabs take the pull of a cable that is yanked sideways and the surface mount tails carry the signal.

The Type-A parts are simpler but they are not all the same. The TE 292303-1 is a right angle through hole body rated 1 A per contact at 30 V AC, with 1,500 mating cycles, a 2.84 mm tail and kinked legs, on a board of 1.57 mm. The Wurth 614004134726 is a right angle through hole body rated 1.5 A, with a contact resistance of 20 mOhm and a withstanding voltage of 750 V AC. The TE 1734366-1 is the vertical version, rated 1 A, for a board of 1.60 mm, where the cable leaves the board at 90 degrees.

The number that decides whether a USB order works is the tab length against the board thickness, and the second is the retention. A receptacle held only by surface mount tails will lift when a stiff cable is pulled away from the panel, which is why the Type-C parts here all have through hole shell tabs. A Type-A part with kinked legs is held in the board by the legs themselves, and the size of the drilled hole has to match the leg or the shell sits high and the plug does not seat.

Key Specifications

ParameterValueApplies to
Type-C contacts24 contacts in 2 rows105450 series, 632723300011
Type-C contact pitch0.5 mm105450 series, 632723300011
Type-C data rateUSB 3.2 Gen 2, 10 Gbps105450-0101, 632723300011
Type-C current rating5 A maximum105450 series, 632723300011
Type-C voltage rating48 V DC105450 series, 632723300011
Type-C mating cycles10,000105450 series, 632723300011
Type-C solder tab length0.60 mm, 0.80 mm or 1.30 mm105450-0011, -0101, -0121
Type-C recommended board0.80 mm or 1.00 mm105450-0121
Type-C contact resistance30 mOhm maximum632723300011
Type-C operating range-30 to +85 CMolex 105450 series
Type-C operating range-40 to +105 CWurth 632723300011
Type-C shellSteel shell, nickel plated632723300011
Type-A contacts4 contacts on a 2 mm pitch292303-1, 1734366-1, 614004134726
Type-A current rating1 A per contactTE 292303-1, TE 1734366-1
Type-A current rating1.5 AWurth 614004134726
Type-A voltage rating30 V ACAll Type-A parts on this page
Type-A mating cycles1,500All Type-A parts on this page
Type-A tail length2.84 mmTE 292303-1
Type-A board thickness1.57 mm right angle, 1.60 mm vertical292303-1, 1734366-1
Shell platingTin over brassTE 292303-1, 1734366-1
FlammabilityUL94 V-0All parts on this page

Included Models and Order Codes

The rows below are the receptacles we quote most often. Tab length and board thickness are given per part because those two decide whether the shell sits flush. A dash means the maker does not publish that figure.

Part NumberTypeContactsOrientation and MountRatingMating CyclesNotes
105450-0101USB Type-C24Right angle, top mount SMT5 A, 48 V DC10,0000.80 mm tabs, gold flash over palladium nickel
105450-0011USB Type-C24Right angle, top mount SMT5 A, 48 V DC10,0000.60 mm tabs for a thin board
105450-0121USB Type-C24Right angle, top mount SMT5 A, 48 V DC10,0001.30 mm tabs, 0.80 or 1.00 mm board
632723300011USB Type-C24Right angle, hybrid THR and SMT5 A, 48 V DC10,00030 mOhm, -40 to +105 C
292303-1USB Type-A4Right angle through hole1 A, 30 V AC1,5002.84 mm kinked tails, 1.57 mm board
1734366-1USB Type-A4Vertical through hole1 A, 30 V AC1,500Board lock, 1.60 mm board
614004134726USB Type-A4Right angle through hole1.5 A, 30 V AC1,50020 mOhm, 750 V AC withstanding

Key Features

Tab length listed per part – The 0.60 mm, 0.80 mm and 1.30 mm tab lengths are separate order codes, so the shell is chosen against the board rather than guessed.

Through hole shell retention – The Type-C parts are held by four shell tabs in plated holes, which is what stops the port lifting when a cable is pulled away from the panel.

Ten thousand cycles – A Type-C port rated 10,000 cycles is the figure that matters on a test instrument where the port is used all day.

Two current classes on Type-A – The 1 A and 1.5 A Type-A parts are both listed, so a port that charges a handset is not built on a 1 A body.

Right angle and vertical – The Type-A family is offered right angle for a board edge and vertical for a cable that leaves through the top of the case.

Wide temperature parts – The Type-C part rated -40 to +105 C covers a box that runs warm, which a -30 to +85 C part does not.

Applications

These receptacles are used where a product needs a standard port that a customer can plug into without a special cable.

Instrument and test gear – A Type-C port carries service data and a 5 V supply on a bench instrument, with the shell taking the wear of a cable that is plugged in daily.

Gateways and data loggers – A right angle Type-A body on the board edge puts a USB stick outside the case, with the kinked legs holding the shell against a sideways pull.

Handheld and portable units – A 1.30 mm tab Type-C part on a 0.80 mm board keeps the port flush on a thin product where the board cannot be thickened.

The receptacle sits on the SUPERB PCB at the board edge, and the SUPERB PCBA route checks the shell tabs against the board thickness before the panel cutout is cut.

Sourcing and Cross-Reference

A USB receptacle is ordered by type and mounting, but it is approved by tab length. A 0.80 mm tab part on a 1.60 mm board leaves the mouth recessed and the plug does not click, and a 1.30 mm tab part on a 0.60 mm board stands proud and rocks. When a port is being replaced, we ask for the board thickness and the old part number, and we match the tab length before the type.

The second point is the shell. A Type-C receptacle that is held only by surface mount tails is fine on a board that sits inside a case with a strain relieved cable, and it is the wrong part on a front panel where the cable is pulled. The parts on this page all use through hole shell tabs for that reason. A Type-A body with kinked legs needs the drilled hole to match, because an oversized hole lets the shell move and a plug that has to be wiggled will wear the contacts.

The third point is what the port is asked to deliver. A 5 A Type-C contact rating does not make a 100 W port: that comes from the controller and the cable, and a board without a power delivery controller is a 5 V port. On Type-A, a 1 A body is the standard USB 2.0 figure, and a 1.5 A body is used where a device draws a little more than the specification allows. We state which body is which rather than quoting a single number for the family.

SUPERB Assembly keeps the connector in its tape until the reflow or the wave step, because the open mouth of a USB receptacle collects solder and flux and cannot be cleaned after the shell is fitted.

Q: Can you supply a Type-C receptacle with 1.30 mm tabs for our 1.00 mm board, and confirm the shell retention before we cut the panel?

A: Send the board thickness, the number of insertions the port will see and whether the port has to deliver 5 A. The SUPERB Tech desk quotes the receptacle with the tab length that matches the board.

Why Buy USB Receptacles Through SUPERB

  1. Tab length matched: The order is built from the board thickness and the tab length, which is where a USB port usually fails to seat.
  2. Retention stated: Shell tabs and kinked legs are described per part, so a front panel port is not built on a surface mount only body.
  3. Rating read correctly: The difference between a contact rating and the power a port delivers is explained before the part is quoted.
  4. Cycle life given: Mating cycles are listed per family, so a port that is used daily is not specified on a 1,500 cycle body.
  5. Fitted at the right step: The receptacle is kept in its tape until reflow or wave, which keeps solder and flux out of the mouth.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: USB Type-C and Power Delivery Controllers for Portable Devices, USB Hubs and Port Controllers for Embedded Hosts, Board to Board and FPC Connectors for Compact Assemblies, Test Points and Spring Contacts for Board Probing, Obsolete Part Cross Reference Hub.