Contact Us

Rubber Bumpers and Feet for Enclosure Support

A bumper is a mechanical part with three numbers: the footprint, the height and the hardness. The urethane pads here run from 7.90 mm to 47.75 mm across and from 2.20 mm to 16.76 mm high, at 67 or 72 Shore M. Shapes are cylinder with a flat top for load bearing, hemisphere for a rounded edge, and square for more contact area on a flat base. The adhesive is a natural rubber R30 pressure sensitive layer on most parts, with an acrylic option where the surface is a low energy plastic.
quote now

Product Specifications

Product Overview

A bumper is the part that decides whether a product slides, scratches or rattles. It is also the part most often chosen from a photograph, which is why a box arrives with feet that flatten under the weight or skid on a desk. The three numbers that matter are the footprint, the height and the hardness, and the fourth is the surface the pad is stuck to.

The 3M Bumpon range on this page is a moulded polyurethane pad with a pressure sensitive adhesive on the back. The standard hardness is 72 Shore M, with the softer clear and quiet parts at 67 Shore M. The urethane does not crack or harden with age the way a PVC foot does, and it does not leave a plasticiser ring on a painted surface, which is the failure that shows up on a desk after a year.

The shape carries the load. A cylinder with a flat top has the largest contact patch for a given diameter, so it is the shape used for a foot under a piece of equipment that sits on a bench. A hemisphere has a smaller contact patch at the same diameter and rolls slightly, which is why it is used where the product has to slide over a surface or where the edge has to be soft. A square pad gives more area on a narrow base and does not turn under a twisting load.

Hardness is the second figure. A 72 Shore M pad under a light instrument is stiff enough to keep the case off the bench and soft enough not to mark it. Under a heavy chassis the same pad deforms and the case sits on the surface, so the answer is a larger diameter at the same height rather than a harder pad, because the harder pad loses the grip that the softer one has. The clear and quiet parts at 67 Shore M are used where the product is a desktop unit and the noise of a fan or a drive is being damped.

The adhesive is the part that fails. The R30 natural rubber layer bonds to a clean, dry, smooth surface and reaches its full strength over about a day, so a unit that is packed straight after the pad is applied will lose a foot in the carton. On a textured powder coat, on a cold surface, or on a low energy plastic such as polypropylene, the rubber layer is the wrong choice and the acrylic version is used instead. Where the pad is loaded in shear by a product that is pushed across a bench, a larger pad is more reliable than a stronger adhesive.

Height and clearance are the last figures. A 2.20 mm pad is a spacer under a board, a 3.56 mm pad is a case foot, and a 9.65 mm hemisphere is a bumper on a door or a lid. The height under a case also sets the airflow gap and the clearance for a screw head, so the pad is chosen with the base rather than after it.

Key Specifications

ParameterValueApplies to
MaterialMoulded polyurethaneAll parts on this page
Hardness72 Shore M, 67 Shore MStandard range, clear and quiet range
AdhesiveNatural rubber R30, acrylicStandard range, clear range
ShapesCylinder flat top, hemisphere, squareRange
Diameter range7.90 mm to 47.75 mmRange
Height range2.20 mm to 16.76 mmRange
ColourBlack, grey, white, brown, clearBy part
PlasticiserFreeAll parts on this page
Bond timeFull strength after about one dayPressure sensitive adhesive

Included Models and Order Codes

The rows below are the pads we quote most often. Shape, diameter, height and hardness are given per part because the load a pad carries is set by all three, and a dash means the maker does not publish that figure.

Part NumberShapeDiameter or WidthHeightHardnessAdhesiveNotes
SJ-5076Cylinder, flat top8.00 mm2.79 mm72 Shore MRubber blendSmall spacer under a board
SJ-5003Hemisphere11.18 mm5.08 mm72 Shore MRubber blendRounded edge bumper
SJ-5738Cylinder, flat top14.20 mm3.00 mm67 Shore MRubber blendSofter pad for a desktop unit
SJ-5008Square12.70 mm3.05 mm72 Shore MRubber blendMore area on a narrow base
SJ-5012Cylinder, flat top12.70 mm3.56 mm72 Shore MRubber blendCommon case foot
SJ-5018Square12.70 mm5.84 mm72 Shore MRubber blendTaller square foot
SJ-5702Hemisphere7.90 mm2.20 mm67 Shore MRubber blendLow profile bumper
SJ-5027Hemisphere16.00 mm7.93 mm72 Shore MRubber blendDoor and lid bumper
SJ-5744Cylinder, flat top19.05 mm4.07 mm72 Shore MRubber blendFoot under a mid size chassis
SJ-5017Hemisphere19.05 mm9.65 mm72 Shore MRubber blendLarge rounded bumper
SJ-5023Square20.63 mm7.62 mm72 Shore MRubber blendLoad bearing pad, flat top
SJ-5009Hemisphere22.35 mm10.16 mm72 Shore MRubber blendHeavy unit bumper
SJ-5532Cylinder, flat top47.75 mm16.76 mm72 Shore MRubber blendLarge foot for a cabinet

Key Features

Shape stated with the size – Cylinder, hemisphere and square are named per part, because the contact patch and the load path differ between them.

Hardness given – 67 and 72 Shore M are listed, so a light desktop unit is not fitted with a pad that will not deform and a heavy one is not fitted with a soft pad that flattens.

Adhesive named – The natural rubber R30 layer and the acrylic option are stated, because a low energy plastic surface needs the acrylic one.

Plasticiser free urethane – The pad does not leave a ring on a painted or lacquered surface, which a plasticised PVC foot does over time.

Height range for clearance – 2.20 mm to 16.76 mm covers a board spacer, a case foot and a door bumper from one range.

Bond time explained – The pad reaches full strength over about a day, which is why a unit is left flat before it is packed.

Applications

These pads are used wherever a product has to stand off a surface, stay put, and not mark what it stands on.

Instrument and test gear – Four 12.70 mm flat top pads at 3.56 mm lift a bench instrument off the surface and hold it against a nudge without marking the bench.

Handheld and portable cases – A 16.00 mm hemisphere on a lid corner takes the impact when a unit is set down, and rolls instead of catching on a table edge.

Rack and cabinet feet – A 47.75 mm pad under a cabinet carries the weight over a large area, so the base does not deform where the load is concentrated.

A bumper adds height under the SUPERB PCB or the case, so the clearance is set before the enclosure is drawn rather than after. On the SUPERB PCBA route the pads are applied last, because a pad that goes through the wash step loses its adhesive.

Sourcing and Cross-Reference

A pad is bought by size and approved by hardness. When a foot is replaced, we ask for the load the pad carries and the surface it sticks to, because the same 12.70 mm pad is a case foot under a handset and a failed foot under a transformer. The second question is the surface finish, because a textured powder coat and a gloss lacquer need different adhesive layers.

The second point is the bond time. The adhesive reaches full strength over about a day, and a unit that is packed an hour after the pads are applied will lose one in the carton. Where a line has to ship the same day, the answer is a pad with a larger footprint rather than a stronger adhesive, and the pad is applied earlier in the build rather than later.

The third point is what the pad is asked to do. A foot carries load, a bumper absorbs an impact and a spacer sets a gap, and the three are different shapes. A hemisphere used as a foot on a heavy chassis deforms at the contact point and the case sits down on one corner, while a flat top cylinder used as a door bumper has a hard edge that marks the surface it hits. We quote the shape against the job rather than against the size that fits the hole.

SUPERB Assembly cleans the surface, applies the pad and leaves the unit flat for a day, because a urethane pad reaches its full bond slowly and a unit packed the same hour will lose a foot in the carton.

Q: Can you supply a 12.7 mm flat top pad at 3.5 mm high that holds a 4 kg instrument on a lacquered bench without marking it?

A: Send the load, the surface the pad sticks to and the height you need. The SUPERB Tech desk quotes the shape and the hardness together, because a hemisphere and a flat top cylinder carry the same load very differently.

Why Buy Bumpers and Feet Through SUPERB

  1. Shape matched to the job: Feet, bumpers and spacers are quoted by what they do, because a hemisphere and a flat top behave differently under load.
  2. Hardness stated: The 67 and 72 Shore M parts are kept apart, so a light unit is not fitted with a pad that will not deform.
  3. Adhesive matched to the surface: The rubber and acrylic layers are quoted against the finish the pad sticks to, which is where a foot usually fails.
  4. Bond time explained: The pad is applied early enough in the build to reach full strength before the unit is packed.
  5. Plasticiser free: The urethane does not mark a painted surface or leave a ring, which is the complaint a plasticised foot generates.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Standoffs Spacers and Mounting Hardware for Board Stacks, Fan Guards and Filter Screens for Enclosure Cooling, Turret Terminals and Solder Lugs for Panel Wiring, Rocker and Toggle Switches for Equipment Panels, How to Verify a Drop in Replacement.