CC0805KRX7R9BB103 CC0805KRX7R9BB103: MLCC 10 nF capacitor, 0805, 50 V, X7R. Original parts with traceability, small quantities and fast quotes from SUPERB.
C1206C225K4RACAUTO C1206C225K4RACAUTO: MLCC 2.2 uF capacitor, 1206, 16 V, X7R. Original parts with traceability, small quantities and fast quotes from SUPERB.
C1210X225K3RAUTO C1210X225K3RAUTO: MLCC 2.2 uF capacitor, 1210, 25 V, X7R. Original parts with traceability, small quantities and fast quotes from SUPERB.
C1210C104KBRACAUTO C1210C104KBRACAUTO: MLCC 100 nF capacitor, 1210, 630 V, X7R. Original parts with traceability, small quantities and fast quotes from SUPERB.
C1206Y104K3RACTU C1206Y104K3RACTU: MLCC 100 nF capacitor, 1206, 25 V, X7R. Original parts with traceability, small quantities and fast quotes from SUPERB.
C0805C225K4RAC C0805C225K4RAC: MLCC 2.2 uF capacitor, 0805, 16 V, X7R. Original parts with traceability, small quantities and fast quotes from SUPERB.
C0805C104J3RACTU C0805C104J3RACTU: MLCC 100 nF capacitor, 0805, 25 V, X7R. Original parts with traceability, small quantities and fast quotes from SUPERB.
C0402C222K4REC7411 C0402C222K4REC7411: MLCC 2.2 nF capacitor, 0402, 16 V, X7R. Original parts with traceability, small quantities and fast quotes from SUPERB.
Inline Fuses and Resettable PTC Fuses for Board Protection Cartridge fuses in a 5 x 20 mm body, 5 A at 250 V AC with a 1.5 kA breaking capacity. Axial PICO fuses at 5 A, 125 V AC and DC, in a 3.18 x 7.10 mm epoxy coated body. Resettable PTCs from 0.5 A to 3.0 A hold, 6 V to 72 V, in 1206, 1812, 2920 and radial packages. Each row lists hold current, trip current and resistance, because those three decide the replacement.
Laser Diodes and VCSEL Emitters for Optical Modules Pulsed 905 nm laser diodes from 70 W to 120 W peak, driven at 30 A to 40 A in a TO-56 can or as a bare die. 850 nm VCSELs at 0.5 mW to 2 mW, and 850 nm datacom VCSELs rated to 10.3125 Gbps, all in TO-46. One 447 nm blue emitter at 3.5 W continuous in a TO-90 can, with 2.2 A of forward current. Every row lists the wavelength band, the drive current and the package, because the package sets the heat path.
VCXO and OCXO Modules for Timing and Synchronization Voltage controlled oscillators from 1 MHz to 220 MHz with pull range from ±25 ppm to ±1600 ppm. Oven controlled parts hold ±10 ppb to ±200 ppb, with warm up inside 3 minutes and 1 W steady state. Phase jitter is 0.225 ps RMS on the differential VCXO and -145 dBc/Hz at 1 kHz on the 10 MHz OCXO. Each row lists the output type, the supply and the package, because those three decide the layout.
PIN Photodiodes and Avalanche Photodiodes for Optical Receivers Silicon PIN photodiodes covering 320 nm to 1100 nm, with bandwidth from 20 MHz to 1 GHz. InGaAs PIN parts for 0.9 um to 2.6 um, and an InGaAs avalanche part for 1000 nm to 1700 nm. Responsivity, dark current, capacitance and cutoff frequency are listed per part number. Active area and package are quoted with the part, because both set the bandwidth.
Film Capacitors for Snubber and AC Filter Applications Metallized polyester film capacitors from 0.1 uF to 1 uF at 63 V and 100 V, in 5 mm lead spacing. X2 class suppression capacitors from 0.1 uF to 0.68 uF at 305 V AC, in 15 mm and 27.5 mm spacing. dv/dt rating, case dimensions and temperature range are listed per part number. The dv/dt figure is what limits the snubber and pulse duty these parts can take.
Ferrite Beads and EMI Suppression Filters for Board Noise Chip ferrite beads in 0603 and 0805 with impedance from 60 Ω to 1000 Ω at 100 MHz. Rated current from 0.5 A to 3.5 A, with DC resistance from 0.020 Ω on the high current parts. Impedance, tolerance, rated current and DC resistance are listed per part number. The DC resistance is what decides the drop on a supply rail; the impedance only works above 10 MHz.
Aluminum Electrolytic and Tantalum Capacitors for Bulk Hold Up Radial and SMD aluminum electrolytics from 220 uF to 1000 uF at 35 V and 50 V. Molded tantalum capacitors from 1 uF to 100 uF, in A, B, C and D cases at 10 V to 35 V. Impedance, ripple current, ESR and case size are listed per part number. Both families are quoted with the derating the maker data sheet asks for.
Power Relays and Signal Relays for Load Switching PCB power relays from 10 A to 12 A at 250 V AC, in sugar cube and low profile cases. Signal relays from 0.3 A to 2 A with 100 mW to 150 mW coils, plus a reed relay with a 0.5 ms operate time. Coil resistance, must operate voltage, contact resistance and mechanical life are listed per part number. Sealed and flux tight versions are quoted with the washing process the board uses.
Baluns and RF Transformers for Differential Signal Paths Surface mount baluns and RF transformers covering 80 kHz to 2.5 GHz in impedance ratios of 1:1 and 1:4. Insertion loss from 0.3 dB in band, with amplitude balance from 0.1 dB and phase balance from 1 degree. Ratio, bandwidth, balance and case style are listed per part number. Ceramic balun filters for 2.4 GHz radios are quoted with their attenuation curve.
Varistors and Gas Discharge Tubes for Surge Protection Metal oxide varistors from S05 to S20 discs, 11 V to 1100 V RMS, with energy from 0.3 J to 151 J. Two electrode gas discharge tubes from 75 V to 1000 V, up to 20 kA on an 8/20 us wave. Clamping voltage, peak current and capacitance are listed per part number. The two device types are quoted together with the coordination resistor between them.
Supercapacitors and Backup Energy Cells for RTC Hold Up Electric double layer cells from 0.1 F to 350 F at 2.7 V, 5.5 V and 8.1 V. ESR from 12 mΩ on a 100 F cell, and leakage current from 10 uA on a coin cell. Cycle life is 500,000 cycles on the cylindrical parts, with 1500 hours at 85 C on the radial types. Each row lists case size and temperature range, because those two decide the substitute.
Charge Pump Regulators and Inverting Converters Switched capacitor inverters, doublers and regulated charge pumps from 1.6 V to 38 V input. Output current runs from 10 mA on the smallest parts to 250 mA on the regulated dual output parts. Oscillator frequency and package are listed per row, with the regulation method named. Parts that keep the ICL7660 pinout are marked, because that footprint still appears on old boards.
Boost and SEPIC Converter Controllers for Wide Input Rails Boost, SEPIC and flyback controllers with input ranges from 2.9 V to 100 V. Synchronous and non-synchronous gate drive options are listed with the peak driver current. Switching frequency, current limit and soft start are set by external parts on every row. Controllers are quoted with the external MOSFET and the sense resistor for a complete stage.
IGBTs and SiC Power Devices for Motor Drives and Inverters IGBT and SiC MOSFET discretes covering 600 V to 1200 V in TO-247, TO-247-4 and TO-3P packages. On-state values are taken from the maker data sheet at the quoted current and temperature. Co-packed IGBTs, SiC MOSFETs and SiC Schottky diodes are quoted together for one phase leg. Parts under an end of life notice are flagged with the nearest equivalent that keeps the footprint.
RF Mixers and IQ Modulators for Frequency Conversion Double balanced passive mixers, active mixers and quadrature modulators for radio front ends. Passive parts cover 2 GHz to 14 GHz with about 8 dB of conversion loss and 24 dBm of input intercept. Active mixers cover 10 MHz to 6 GHz with an integrated LO buffer. IQ modulators cover 400 MHz to 6 GHz with 9.6 dBm of output compression at 900 MHz.
24-Bit Delta-Sigma ADCs for Precision Measurement Delta-sigma converters with 24 bit resolution and no missing codes at any gain setting. One to eight input channels, differential or single ended, with a PGA from 1 to 128. Data rates from 10 samples per second on bridge parts to 30 kSPS on the wideband parts. Simultaneous 50 Hz and 60 Hz rejection on the low power eight channel part.
Analog Switches and Multiplexers for Signal Routing CMOS analog multiplexers for routing sensor and reference signals to one converter. On resistance from 2.5 ohm to 70 ohm, flatness down to 1 ohm across the signal range. Eight to one single ended and four to one differential configurations. Single supply from 3.3 V and dual supply up to plus or minus 15 V.
PFC Controllers for AC-DC Front Ends Active power factor controllers for boost stages in AC-DC front ends. Continuous conduction mode parts hold a fixed frequency from 18 kHz to 250 kHz. Critical conduction mode parts cover adapters and ballasts up to about 350 W. Average current control, brown out detection and open loop protection on chip.
PCIe Clock Generators and Redrivers for High Speed Links Clock generators, fanout buffers and redrivers for PCI Express links from Gen 1 to Gen 5. Two to eight low power HCSL outputs with integrated 100 ohm terminations. Additive phase jitter from 40 fs to 156 fs depending on the buffer and the standard. Eight channel redrivers add 36 dB of receiver equalisation for long backplanes.
Battery Protection ICs and BMS Analog Front Ends Protection and monitoring devices for lithium packs from one cell to eighteen cells in series. Cell measurement of 5 mV at 25 degrees on the BQ76952, with coulomb counting on the same die. Single cell protectors add overcharge, overdischarge and short circuit cut off in a 1.5 mm package. isoSPI and I2C interfaces for packs that stack several monitors.
Hall Effect Current Sensors for Motor and Supply Monitoring Galvanically isolated current sensors built around a Hall element and an integrated conductor. Ranges from plus or minus 5 A to plus or minus 150 A, with 66 mV/A to 400 mV/A sensitivity. Bandwidth from 80 kHz to 400 kHz, isolation from 2.1 kVRMS to 5 kVRMS. Ratiometric and fixed output versions for 3.3 V and 5 V control boards.
MEMS Microphones for Voice and Acoustic Sensing Digital and analog MEMS microphones in bottom port and top port packages. Signal to noise ratio from 64 dB to 70 dB, acoustic overload from 120 dBSPL to 130 dBSPL. PDM parts run from a clock line, I2S parts need no audio codec on the board. Sensitivity tolerances of plus or minus 1 dB keep array channels matched.
USB Hubs and Port Controllers for Embedded Hosts Hub controllers that turn one upstream port into two to seven downstream ports. USB 3.2 Gen 1 parts run at 5 Gbps with a separate USB 2.0 path. Multiple transaction translators keep full speed devices from blocking a port. Per port power switching, overcurrent detection and battery charging are on chip.
Digital Step Attenuators for RF and Instrument Signal Chains Silicon and GaAs step attenuators with parallel or serial control. Attenuation ranges of 7.75 dB, 31.5 dB and 31.75 dB in 0.25 dB or 0.5 dB steps. Insertion loss from 1.1 dB at 1 GHz to 4.5 dB at 40 GHz depending on the part. Glitch free transitions and monotonic steps for closed loop level control.
Instrumentation Amplifiers for Sensor and Bridge Signals Difference amplifiers with a one resistor gain setting, from 1 to 10,000. Chopper stabilised and JFET input parts hold offset drift below 1 microvolt per degree. Voltage noise spans 1 nV to 50 nV per root hertz across the range. Single supply parts run from 1.8 V for battery powered sensor boards.
I2C and SPI EEPROM ICs for Configuration and Calibration Data I2C and SPI serial EEPROM from 2 Kbit to 1 Mbit in 8 lead packages. Supply from 1.7 V, which covers a coin cell and a 1.8 V rail without a regulator. One million write cycles and 100 to 200 years of data retention. Page sizes from 8 to 256 bytes, with hardware and block write protection.
Ethernet Magnetics and PoE Transformers for Network Ports Single and dual port LAN magnetics for 10/100BASE-TX and 1000BASE-T. 1:1 turns ratio modules with 350 microhenry of open circuit inductance. 1500 Vrms hipot and common mode rejection from 43 dB at 30 MHz. PoE variants rated for four pair power up to 30 W at the module.
Audio Codecs for Voice and Instrumentation Stereo 24 bit ADC and DAC pairs with 92 to 98 dB of signal to noise ratio. Integrated headphone drivers, and class D speaker drivers up to 1 W per channel. Sample rates from 8 kHz for voice to 96 kHz for instrumentation. I2S, left justified, DSP and TDM digital audio interfaces with I2C control.
SAW Filters and Duplexers for RF Front Ends GPS and GNSS SAW filters at 1575.42 MHz with insertion loss from 0.75 dB. TC-SAW and BAW duplexers for Band 8 and Band 3 small cell and repeater front ends. Ceramic and plastic packages from 1.1 by 0.9 mm to 2.5 by 2.0 mm. Rejection figures stated against the bands that actually interfere.
RF Switches and PIN Diode Switches for Signal Routing SPDT, SP4T and bypass switches covering DC to 8 GHz, and one family to 20 GHz. Isolation from 30 dB at 1 GHz to more than 50 dB below 5 GHz on the HMC547. Insertion loss from 0.35 dB at 1 GHz on a 1 by 2 mm SC-70 switch. PIN diodes with 0.13 pF capacitance for high voltage, low distortion routing.
MEMS Accelerometers for Vibration and Tilt Measurement Three axis MEMS accelerometers with digital or analog output and ranges from 2 g to 50 g. Noise density from 22.5 microgram per root hertz on the 20 bit ADXL355. Supply current from 1.8 microamp at 100 Hz on the ADXL362. LCC, LGA and QFN packages, with SPI or I2C output and embedded FIFO.
Temperature and Humidity Sensors for Environmental Monitoring Capacitive humidity sensing elements with an on chip temperature sensor and I2C output. Typical RH accuracy from 0.5 percent on the HDC3020 to 2 percent on the SHTC3. Average current from 0.4 microamp, which suits a battery logger sampling once a minute. Packages from 1.5 by 1.5 mm, with filter membranes for condensing environments.