Contact Us
  • Home
  • COMPONENTS
  • SIM and Memory Card Holders for Field Accessible Storage

SIM and Memory Card Holders for Field Accessible Storage

A card holder is the one connector a customer opens in the field, so retention and the detection switch matter as much as the contact count.\\nThe SIM parts here use 6 contacts on the ISO 7816 and GSM 11.11 layout, with a hinged lid or a push-push slot, rated 5,000 cycles.\\nThe microSD parts use 8 contacts on a 1.10 mm pitch, with heights of 1.42 mm, 1.68 mm and 1.83 mm above the board.\\nAll of the microSD parts carry a card detection switch and are rated 10,000 cycles at 0.5 A.
quote now

Product Specifications

Product Overview

Two card types end up behind a panel cutout: the SIM card, which holds the identity for a radio link, and the microSD card, which holds logs, maps or a configuration file. They are different connectors with different failure modes, but they share three requirements. The card has to stay in place when the unit is dropped. The firmware has to know whether a card is present. And the solder joints have to survive the force of a card being pushed in by hand, which is a larger load than any signal the connector carries.

The Amphenol C707 10M006 512 2 is a SIM reader with a hinged lid. It has 6 contacts on the 3 plus 3 layout defined by ISO 7816 and GSM 11.11, a contact resistance below 60 mOhm, a durability of 5,000 cycles and an operating range of -40 to +85 C. The insulator is a high temperature thermoplastic rated UL94 V-0, the contacts are gold over nickel, and the test voltage is 540 V RMS. This part has wider solder pads and no positioning pins, which is the version used where the board is located by the cutout rather than by pins.

The Yamaichi FMS006Z is the push-push alternative. A card is pushed in until it locks and pushed again to release, which means no lid to open and no lid to lose. It is rated 0.5 A at 5.0 Vrms, with a contact resistance of 100 mOhm or less, a durability of 5,000 insertions and a range of -55 to +85 C. The insulator is glass filled LCP rated UL94 V-0. The FMS006Z-2001-1 carries a card detection switch, and the FMS006Z-2000-0 does not, which matters when the firmware has to report a missing SIM rather than simply fail to register.

The Molex 104031-0811 is a microSD holder with a push-pull action: the card is pushed in to make contact and pulled out to remove it, with no eject mechanism. It has 8 contacts on a 1.10 mm pitch, sits 1.42 mm above the board, and is rated 0.5 A at 10 V with 10,000 cycles and a range of -25 to +85 C. The housing is LCP rated UL94 V-0, the contacts are gold plated, and the part includes a card detection switch. Its value is the low height: 1.42 mm is what allows a card slot under a lid on a handheld unit.

The Hirose DM3AT-SF-PEJM5 is the push-push microSD holder. It has 8 positions on a 1.1 mm pitch, sits 1.68 mm above the board, and ejects the card 4.0 mm so it can be gripped. It is rated 0.5 A at 125 V AC, with 10,000 cycles, a contact resistance of 100 mOhm or less and a range of -25 to +85 C. The card detection switch is normally open. The DM3BT-DSF-PEJS is the reverse mount version at 1.83 mm, for a board where the card side faces away from the components.

The number to read first is the height above the board, because it decides whether the card can be inserted under a lid and whether the mouth lines up with the cutout. The second is the card detection switch, because a holder without one leaves the firmware to poll the card and report an error rather than a missing card. The third is the hold-down. A microSD card is inserted with a thumb, and the two hold-down tabs take that load. A holder that is held only by its signal pads will lift at the corner after a few hundred insertions, which is why the parts here all have shield tabs or legs.

Key Specifications

ParameterValueApplies to
SIM contacts6 contacts, 3 plus 3 layoutC707 10M006 512 2, FMS006Z
SIM standardISO 7816 and GSM 11.11C707 series, FMS006Z
SIM insertionHinged lid or push-pushC707 series, FMS006Z
SIM durability5,000 cyclesC707 series, FMS006Z
SIM current rating0.5 AFMS006Z
SIM voltage rating5.0 VrmsFMS006Z
SIM contact resistance60 mOhm maximum, 100 mOhm maximumC707 series, FMS006Z
SIM operating range-40 to +85 C, -55 to +85 CC707 series, FMS006Z
SIM insulatorHigh temperature thermoplastic, glass filled LCPC707 series, FMS006Z
microSD contacts8 contacts on a 1.10 mm pitch104031-0811, DM3AT, DM3BT
microSD height above board1.42 mm, 1.68 mm or 1.83 mm104031-0811, DM3AT, DM3BT
microSD insertionPush-pull or push-push104031-0811, DM3AT
microSD eject distance4.0 mmDM3AT-SF-PEJM5
microSD durability10,000 cycles104031-0811, DM3AT, DM3BT
microSD current rating0.5 A104031-0811, DM3AT
microSD voltage rating10 V DC, 125 V AC104031-0811, DM3AT
Card detection switchNormally open, fitted on all parts listed104031-0811, DM3AT, DM3BT, FMS006Z-2001-1
Contact resistance, microSD100 mOhm maximum104031-0811, DM3AT
microSD operating range-25 to +85 C104031-0811, DM3AT, DM3BT
Housing flammabilityUL94 V-0All parts on this page

Included Models and Order Codes

The rows below are the holders we quote most often. Height above the board and the insertion style are given per part, because those two decide whether the card can be reached through the panel. A dash means the maker does not publish that figure.

Part NumberCard TypeContactsHeightInsert and EjectDetect SwitchCyclesNotes
104031-0811microSD81.42 mmPush-pullYes10,0001.10 mm pitch, SMD right angle
DM3AT-SF-PEJM5microSD81.68 mmPush-pushYes10,000Ejects 4.0 mm, 1.1 mm pitch
DM3BT-DSF-PEJSmicroSD81.83 mmPush-pushYes10,000Reverse mount, card side under the board
C707 10M006 512 2SIM6 (3+3)-Hinged lidOptional5,000Wider solder pads, no positioning pins
C707 10M006 522 2SIM6 (3+3)-Hinged lidYes5,000With lock detect switch
FMS006Z-2000-0SIM6-Push-pushNo5,000GSM 11.11 layout, glass filled LCP
FMS006Z-2001-1SIM6-Push-pushYes5,0000.5 A, 5.0 Vrms, -55 to +85 C

Key Features

Height stated per part – The 1.42 mm, 1.68 mm and 1.83 mm heights are given separately, so a slot under a lid is chosen on the space that is actually there.

Detection switch stated – Every row says whether the holder detects the card, because a holder without a switch changes what the firmware has to do.

Push-pull and push-push – Both microSD styles are listed, so a low cost slot and a slot that ejects the card for a thumbnail can both be quoted.

SIM lid and slot – The hinged lid and the push-push SIM reader are both listed, which covers a unit that is opened once and one that is opened often.

Ten thousand cycles – The microSD parts are rated 10,000 cycles, which covers a logger whose card is swapped every week for years.

Hold-down tabs – The holders use shield tabs or legs rather than signal pads alone, because the insertion force is taken by the shell.

Applications

These holders are used where a card has to be inserted or replaced by the person using the product, not only at the bench.

Cellular gateways and routers – A push-push SIM reader lets a field engineer change the SIM through a cutout, with the detection switch telling the firmware whether a card is present.

Data loggers and meters – A 1.42 mm microSD slot fits under the lid of a handheld logger, and the 10,000 cycle rating covers a card that is swapped every service visit.

Access control and payment terminals – A hinged lid SIM reader holds the card against vibration, which is what a terminal mounted on a door needs.

The holder is fitted on the SUPERB PCB next to the cutout, and the SUPERB PCBA route checks that the card mouth lines up with the panel opening before the case is closed.

Sourcing and Cross-Reference

A card holder is ordered by card type, but it is approved by height and by the cutout. A 1.83 mm reverse mount part cannot be used on a board that sits 1.5 mm below the panel, and a 1.68 mm push-push part needs 4.0 mm of free space in front of the mouth so the card can be gripped. When a holder is being replaced, we ask for the panel cutout drawing and the height under the lid, and we match those before the contact count.

The detection switch is the second point, and it is the one that gets missed. A holder without a switch works only if the firmware polls the card, which on some boards shows as a read error rather than a missing card. The parts on this page are listed with and without the switch, and the difference is stated per part number rather than left to the family name.

The third point is mechanical. A microSD card is pushed in with a thumb, and the load goes into the hold-down tabs. A holder with plated signal pads only will lift a corner after a few hundred insertions, and the failure looks like an intermittent card rather than a broken connector. The parts here use shield tabs or legs into plated holes. We also keep the holder covered until the board goes into the case, because solder or flux inside the slot is very hard to remove once the shell is closed.

SUPERB Assembly keeps the card holder covered until the board goes into the case, because a single grain of solder inside the slot will stop a card from seating and is very hard to clear.

Q: Can you supply a microSD holder that fits a 1.5 mm gap under our lid and has a card detection switch, and confirm the cutout size?

A: Send the card type, the panel cutout and the height available under the lid. The SUPERB Tech desk quotes the holder with the right insertion height and the detection switch that matches your firmware.

Why Buy Card Holders Through SUPERB

  1. Height matched to the lid: The order is built from the space under the lid and the height above the board, which is where a card slot usually fails to fit.
  2. Switch stated per part: The detection switch is listed per part number, so the firmware is written against the right holder.
  3. Both SIM styles: A hinged lid part and a push-push part are both quoted, for a unit that is opened once and one that is opened weekly.
  4. Cycle life given: The 5,000 and 10,000 cycle ratings are stated, so a card that is swapped often is not put in a 5,000 cycle part.
  5. Handled clean: The holder is kept covered until the case is closed, which keeps solder out of a slot that cannot be cleaned.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: USB Type-C and USB A Receptacles for Power and Data Ports, Battery Holders and Coin Cell Retainers for Backup Power, Board to Board and FPC Connectors for Compact Assemblies, Tactile and Slide Switches for Front Panel Control, Obsolete Part Cross Reference Hub.