Contact Us

IR Receiver Modules for Remote Control and Data

An IR receiver module is a photodiode, a band pass filter and a demodulator in one three pin package, and it outputs a clean logic pulse.\nThe 38 kHz parts here run from 2.5 to 5.5 V, draw about 0.35 mA, and reach 24 m with a 50 mA emitter on the axis.\nHalf transmission angle is plus or minus 45 degrees, and the package is 5.0 x 6.95 x 4.8 mm on the minicast parts.\nAGC2 and AGC4 versions are both listed, because the choice decides which remote codes are accepted in daylight and under lamps.
quote now

Product Specifications

Product Overview

An IR receiver module takes the place of a photodiode, an amplifier, a filter and a comparator. Inside the package there is a PIN diode, a preamplifier, a band pass filter centred on the carrier frequency and an automatic gain control stage. The output is already demodulated, so a microcontroller can read it on a digital pin and decode the burst pattern without any analogue work. That is why the module has replaced the discrete receiver on almost every remote control product.

The parts on this page are Vishay TSOP modules and Everlight IRM modules. The TSOP38238 and TSOP38438 are 38 kHz minicast parts, 5.0 mm wide, 6.95 mm high and 4.8 mm deep, with pins on a 2.54 mm row. Supply range is 2.5 to 5.5 V, supply current is 0.35 mA typical at 3.3 V with no signal, and the output can sink 5 mA. The difference between the two is the AGC setting: the 382 series uses AGC2, which is the legacy setting kept for compatibility with older remotes, and the 384 series uses AGC4, which suppresses interference from compact fluorescent lamps and LED drivers but can reject some long burst codes.

The TSOP48 series is the same function in a moulded package that is 6.0 mm wide, 6.95 mm high and 5.6 mm deep. It shares the 38 kHz carrier and the 2.5 to 5.5 V supply, but the pin order is different: on the 48 series pin 1 is the output, pin 2 is ground and pin 3 is the supply, while on the 22 and 24 series pin 2 is the supply and pin 3 is ground. A board laid out for one will not work with the other, and that is the first thing to check when a part is being replaced.

The Everlight IRM-3638 and IRM-3640 are the lower cost route. They are 38 kHz and 40 kHz parts in a 3 pin package, with a supply current of 2 mA maximum, a reception distance of 14 m on the axis and a half angle of 45 degrees in both planes. The minimum burst length is 6 to 10 pulses, which suits the common NEC and RC5 codes. Operating range is -25 to +80 C, which is narrower than the Vishay parts and is worth knowing on an outdoor panel.

Two numbers decide whether a product works in a room with windows. The first is the half angle: at plus or minus 45 degrees the module sees a wide cone, which is what a hand held remote needs, but it also sees more of the room light. The second is the AGC setting. A receiver with AGC4 will reject the 100 Hz ripple from a fluorescent lamp, and it will also reject a remote whose burst is longer than the filter expects. Where a product has to work with an existing remote, the AGC2 part is usually the safe choice; where it has to work next to LED lighting, the AGC4 part is.

Key Specifications

ParameterValueApplies to
Carrier frequency30, 33, 36, 38, 40 or 56 kHzTSOP382 and TSOP384 series
Carrier frequency38 kHz, 40 kHzEverlight IRM-3638 and IRM-3640
Supply voltage2.5 to 5.5 VTSOP382 and TSOP384 series
Supply current0.35 mA typical at 3.3 V, no signalTSOP38238
Supply current2 mA maximumEverlight IRM-36xx
Transmission distance24 m with a TSAL6200 at 50 mATSOP38238
Transmission distance14 m on axisEverlight IRM-3638
Half transmission angleplus or minus 45 degreesAll parts on this page
Output current5 mATSOP and IRM modules
Output levelActive low, open collectorAll parts on this page
Package, minicast5.0 W x 6.95 H x 4.8 D mmTSOP382 and TSOP384 series
Package, moulded6.0 W x 6.95 H x 5.6 D mmTSOP48 series
Operating temperature-25 to +85 CTSOP series
Operating temperature-25 to +80 CEverlight IRM-36xx
Minimum burst length10 cycles for TSOP, 6 to 10 pulses for IRMPer part number

Included Models and Order Codes

The rows below are the modules we quote most often. The pin order is the field to read first, because the 48 series and the 22 and 24 series put the supply and ground on opposite pins. A dash means the maker does not publish that figure in the summary sheet.

Part NumberCarrierAGCSupplyRangePackagePin Order
TSOP3823838 kHzAGC22.5 to 5.5 V24 mMinicast, 5.0 x 6.95 x 4.8 mm1 OUT, 2 GND, 3 VS
TSOP3843838 kHzAGC42.5 to 5.5 V24 mMinicast, 5.0 x 6.95 x 4.8 mm1 OUT, 2 GND, 3 VS
TSOP3823636 kHzAGC22.5 to 5.5 V24 mMinicast, 5.0 x 6.95 x 4.8 mm1 OUT, 2 GND, 3 VS
TSOP3845656 kHzAGC42.5 to 5.5 V24 mMinicast, 5.0 x 6.95 x 4.8 mm1 OUT, 2 GND, 3 VS
TSOP483838 kHzAGC22.5 to 5.5 V24 mMoulded, 6.0 x 6.95 x 5.6 mm1 OUT, 2 GND, 3 VS
TSOP223838 kHzAGC22.5 to 5.5 V24 mMoulded, 6.0 x 6.95 x 5.6 mm1 OUT, 2 VS, 3 GND
TSOP443838 kHzAGC42.5 to 5.5 V24 mMoulded, 6.0 x 6.95 x 5.6 mm1 OUT, 2 GND, 3 VS
TSOP173838 kHzAGC14.5 to 5.5 V-Moulded, 10 x 5.3 mm1 GND, 2 VS, 3 OUT
IRM-3638M338 kHzStandard2.7 to 5.5 V14 mDIP, 3 pin1 OUT, 2 GND, 3 VS
IRM-3640M340 kHzStandard2.7 to 5.5 V14 mDIP, 3 pin1 OUT, 2 GND, 3 VS

Key Features

Demodulated output – The module delivers a logic pulse, so the microcontroller reads a pin instead of sampling an analogue photodiode and running a software filter.

AGC2 and AGC4 in one footprint – The same minicast package is offered with both gain control settings, so a board can be moved between a legacy remote and a lamp immune build without a layout change.

Stated range at a stated emitter current – The 24 m figure is given with a 50 mA emitter, which makes the number comparable instead of a best case claim.

Narrow and wide optical filters – The maker offers filter variants for a narrow or a wide optical window, which is how a receiver is matched to the window in the enclosure.

Pin order documented – The pin order is stated for every row, because the 48 series and the 22 and 24 series are not interchangeable on a board.

Low supply current – At 0.35 mA typical the receiver can stay powered in a battery product, and the 5 mA output rating is enough for a direct connection to a microcontroller pin.

Applications

These modules are used wherever a product is controlled by a hand held remote or by an infrared data link.

Consumer and instrument remotes – A 38 kHz receiver decodes NEC, RC5 and RC6 codes from a hand held remote, with the AGC setting chosen for the lighting in the room.

Set top boxes and audio units – The minicast package fits behind a dark window on the front panel, and the 45 degree half angle covers a remote used off axis.

Metering and data links – An IR link reads a meter or a controller without opening the case, using a 38 kHz carrier and a short burst protocol.

The receiver sits on the SUPERB PCB behind a window in the enclosure, and the SUPERB PCBA route checks the supply decoupling and the distance to the window against the drawing before the board is released.

Sourcing and Cross-Reference

The receiver is a part where a small difference stops the product. The pin order, the carrier frequency and the AGC setting all have to match, and only the first is visible on a footprint. A 38 kHz part will not decode a 36 kHz remote, an AGC4 part can reject an old long burst code, and a 22 series part in a 48 series footprint will put the supply on the output pin. We confirm all three against the old part number before quoting.

The second point is the optical window. A receiver behind a dark red window loses range, and a receiver behind a clear window picks up more ambient light. The maker's filter options are there to balance the two, and the window material is part of the decision. When a customer is changing the window, we ask for the transmission curve rather than the colour, because two red windows can differ by a factor of two at 950 nm.

Parts in this family are also sold under several maker names for the same die. A customer who has a TSOP1738 on an old build is often offered the 38238 as a replacement, and it works electrically, but the pin order and the package are different. We check the footprint and the pin order before offering a substitute, and we do not treat the carrier frequency alone as a match.

SUPERB Assembly fits the receiver after the wash step, or uses the sealed version, because a module that has been washed can trap water under the epoxy lens and lose sensitivity.

Q: Can you supply a 38 kHz receiver with the same pin order as our current part, and confirm which AGC setting suits our remote?

A: Send the carrier frequency of the remote, the supply rail and the height of the window above the board. The SUPERB Tech desk quotes the module that matches the code and the optical path.

Why Buy IR Receiver Modules Through SUPERB

  1. Pin order checked first: The 48 series and the 22 and 24 series are not interchangeable, so the pin order is confirmed before a replacement is quoted.
  2. Carrier and AGC matched: The carrier frequency and the gain control setting are matched to the remote that is actually in use, not only to the part that is in the drawing.
  3. Filter option explained: Narrow and wide optical filter versions are described against the window material, so the range does not collapse behind a dark window.
  4. Package options: Minicast and moulded packages are both listed with their dimensions, so the part fits the height and the window in the enclosure.
  5. Fitted after the wash: The receiver is fitted after cleaning or the sealed version is used, which avoids water trapped under the lens.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Photointerrupters and Optical Switches for Position Detection, Phototransistors and Ambient Light Sensors, Inductive Proximity and Photoelectric Sensors for Automation, High Power LED Emitters for Illumination and Infrared, Sensor Cross Reference.