Contact Us
  • Home
  • COMPONENTS
  • Enclosure Handles and Corner Guards for Portable Units

Enclosure Handles and Corner Guards for Portable Units

A portable unit is carried by its handle and protected by its corners, and both parts are chosen by load rather than by appearance. The handles here run from a 35 kg surface sprung part in 1.2 mm steel to a 150 kg double sprung recessed part with a 10 mm dish and 14 fixing holes. The corner guards are 2 leg or 3 leg steel parts from 0.8 mm to 2.0 mm thick, with internal radii from 3/8 inch to 1/2 inch and zinc or nickel finish. Load rating, dish depth and fixing hole diameter are given per part, because those three figures decide whether the handle fits the panel.
quote now

Product Specifications

Product Overview

A handle on a portable enclosure does two jobs. It carries the mass of the unit, and it keeps the fingers of the person carrying it away from the panel edge. A surface handle sits on the outside of the panel and adds depth to a case that is already built. A recessed handle sits in a dish, so the bail folds into the panel and the case slides into a rack or a van without the handle catching on anything. The two families are not interchangeable once the sheet metal is cut, because one needs a rectangular opening and the other needs four or five holes.

The recessed handles on this page are the Penn Elcom Ultimate and medium series. The Ultimate shallow recessed handle H7165-10EZ-RP is the largest part here: a 178 mm by 127 mm body in 1.2 mm steel, a dish 10 mm deep, 14 fixing holes, a 5/16 inch bail and a 19 mm grip, rated at 150 kg per handle. The medium H7151Z is the same 1.2 mm steel and the same 150 kg rating in a smaller body, with a dish 8.5 mm deep, a 6.35 mm bail, a 15 mm grip and 5 mm fixing holes. Both are double sprung, which means the bail stays down when it is released rather than springing up and rattling against the case.

The surface handles are the parts used on a case that is already built or on a cabinet that has no room for a dish. The H1052Z and H1053Z are one piece spring loaded assemblies in 1.2 mm and 1.6 mm steel, rated at 35 kg per handle, with a 6.35 mm or 7.9 mm bail and a 15 mm or 19 mm grip, fixed through 5 mm holes. The 2351 and 2356 are the heavier zinc surface parts, rated at 80 kg and 60 kg per handle, with four and six fixing holes and a 19 mm grip. On a case that is handled by two people the surface part is the practical choice, because it needs no opening in the panel.

The load rating is the figure that is read wrong most often. A rating of 150 kg per handle is a working load for a pair of handles on a case that is carried by two people, and the same handle on a 200 kg case is being asked for more than the pair was rated for. The rating also assumes the fixing points are in sound material: a handle rated at 150 kg on 1.2 mm aluminium with two rivets in a 20 mm land will tear the panel long before the bail bends. Where the panel is thin, the welded captive plate version of the same handle spreads the load, and the plate is a different part number.

The dish depth and the fixing pattern are the second pair of figures. A recessed handle needs an opening in the panel and a clear depth behind it, and the dish is what sets that depth: 8.5 mm on the medium part and 10 mm on the Ultimate part. That depth has to clear whatever is behind the panel, which on a tightly packed case is often the board or the connector shell. The fixing holes are equally specific: 14 holes on the Ultimate part and 5 mm holes on the medium part, and those two patterns are not interchangeable even though both handles are rated at 150 kg.

The corner guards are the other half of the page, and they are the part that takes the impact. A 3 leg ball corner in 2.0 mm steel with a 13/64 inch internal radius wraps the corner in three planes, which is what a flight case or a portable instrument needs when it is dropped on a corner. A 2 leg wrap around corner in 0.8 mm steel with countersunk holes is the lighter answer for a cabinet that is mounted rather than carried. The internal radius has to match the radius already formed in the sheet metal, because a corner guard with a 1/2 inch radius on a panel formed at 3/8 inch will sit proud on one face and leave a gap on the other.

Key Specifications

ParameterValueApplies to
Handle typesRecessed double sprung, surface sprung, surface formed bailHandles on this page
Handle steel1.2 mm (18 gauge), 1.6 mm (16 gauge)By series
Handle finishPennBrite zincAll handles listed
Recessed handle load150 kg per handleH7165-10EZ-RP, H7151Z
Surface handle load35 kg, 60 kg, 80 kg per handleH1052Z, H1053Z, 2356, 2351
Dish depth8.5 mm, 10 mmMedium and Ultimate recessed parts
Fixing holes5 mm, 5.2 mm, 14 hole patternBy part
Bail diameter6.35 mm (1/4 inch), 7.9 mm (5/16 inch)By part
Grip size15 mm, 19 mmBy part
Opening angle90 degreesSprung handles
Corner steel0.8 mm (1/32), 1.6 mm (1/16), 2.0 mm (5/64)Corner guards
Corner legs2, 3Corner guards
Corner internal radius3/8 inch, 13/64 inch, 1/8 inch, 1/2 inchBy part
Corner finishZinc, nickelBy part
Corner fixing holes2, 3, 6By part

Included Models and Order Codes

The rows below are the handles we quote most often. Load rating, fixing and dish depth are given per part because those figures decide whether a handle fits a panel that is already cut, and a dash means the maker does not publish that figure.

Part NumberTypeLoad Per HandleFixingSteelWeightNotes
H7165-10EZ-RPRecessed, double sprung150 kg14 holes, 10 mm dish1.2 mm514 g178 x 127 mm, 19 mm grip, 5/16 inch bail
H7151ZRecessed, double sprung150 kg5 mm holes, 8.5 mm dish1.2 mm320 g15 mm grip, 6.35 mm bail
2351Surface, formed bail80 kg4 holesSteel body216 g19 mm grip, spring loaded
2356Surface, spring loaded60 kg6 holesSteel body201 g19 mm grip, zinc
H1053ZSurface, sprung35 kg5 holes1.6 mm223 g19 mm grip, deluxe bail
H1052ZSurface, sprung35 kg5 mm holes1.2 to 1.5 mm216 g15 mm grip, 6.35 mm bail

Corner Guards and Ball Corners

Corner guards are quoted by leg count and internal radius, because that radius has to match the radius already formed in the sheet metal. Steel gauge and fixing holes are given per part.

Part NumberLegsInternal RadiusSteelHolesWeightFinishNotes
C1377Z313/64 inch2.0 mm (5/64)6120 gZincHeavy duty ball corner, mates C1377/01
C1385Z31/8 inch2.0 mm (5/64)6121 gZincFemale stackable, mates C1375Z
C1835Z31/2 inch1.6 mm (1/16)3 x 4.6 mm25 gZincCabinet corner, plain holes
C1823N31/2 inch1.6 mm (1/16)321 gNickelCabinet corner, plain holes
1087N225/64 inch0.8 mm (1/32)223 gNickelWrap around, countersunk holes

Key Features

Load rating stated per handle – 35 kg, 60 kg, 80 kg and 150 kg parts are listed with their rating, so a pair of handles is chosen against the mass of the case and not against the size of the bail.

Dish depth before the cut – 8.5 mm and 10 mm dish depths are given for the recessed parts, because the depth behind the panel has to clear the board and the connector shells.

Fixing pattern per part – 5 mm, 5.2 mm and a 14 hole pattern are listed, so a replacement handle is not ordered by rating and then found to have a different hole spacing.

Double sprung bail – The bail stays down when it is released, which is what keeps a recessed handle from rattling against the case in transit.

Corner radius matched to the panel – Internal radii from 1/8 inch to 1/2 inch are listed, so a guard is picked against the radius already formed in the sheet metal.

Steel gauge from 0.8 to 2.0 mm – Light wraparound guards and 2.0 mm heavy duty ball corners are on the same page, because a cabinet and a portable case need different impact protection.

Applications

These parts are used on any unit that is lifted by hand, rolled between sites or stacked in a van.

Portable test and measurement cases – A 150 kg recessed handle with a 10 mm dish folds flat, so the instrument slides into a rack shelf without the bail catching on the rail.

Transit cases for field equipment – 2.0 mm heavy duty ball corners on all eight corners take the drop, with the 13/64 inch radius matching the corner formed in the case shell.

Wall and rack cabinets – A 3 leg cabinet corner with a 1/2 inch radius finishes the corner of a mounted enclosure, with three holes in 1.6 mm steel holding it to the panel.

A handle is the first part a user touches, so the fixing pattern is checked against the SUPERB PCB layout and the panel cut before the sheet metal is bent. On the SUPERB PCBA route the handle and the corner guards are fitted last, because a case that is carried before the board is in place takes the load on the seam rather than on the frame.

Sourcing and Cross-Reference

A handle is bought by load and approved by fixing pattern. When a handle is replaced on a case that is already in service, the rating on the old part is not enough, because a 150 kg recessed part and a 60 kg surface part can both look right on a photograph. We ask for the mass of the loaded case, the panel thickness at the fixing points and the depth available behind the panel, and the part is chosen from those three figures.

The second point is the panel. A handle rated at 150 kg transfers that load into four, five or fourteen fixing points, and the panel has to be sound at each one. On 1.2 mm steel with a 20 mm land the rivets will pull through before the bail bends, which is why the welded captive plate version of the same handle exists. Where the case is aluminium and the panel is thin, the plate and a larger washer are the answer rather than a heavier handle.

The third point is the corner. A corner guard is a wear part, and the right one depends on how the case travels: a 0.8 mm wrap around guard for a cabinet that is mounted, a 1.6 mm cabinet corner for a case that is stacked, and a 2.0 mm ball corner for a case that is dropped. The internal radius has to match the panel, and the fixing holes have to miss the extrusion or the seam behind the corner. We quote the guard with its radius and its hole count, because a guard that does not sit flat is a guard that comes loose.

SUPERB Assembly sets the handle on the first unit and lifts it with the ballast fitted, because a handle rated on paper and a handle with two screws biting 3 mm of 1.2 mm steel are different parts in the hand.

Q: Can you supply a recessed handle rated at 150 kg with a 10 mm dish for a 1.5 mm aluminium panel, and confirm the fixing hole pattern and the corner guard radius to match?

A: Send the case mass, the panel thickness at the fixing points and the depth available behind the panel. The SUPERB Tech desk quotes the handle with its load rating and its dish depth, because a 150 kg recessed handle needs 10 mm of panel depth and 14 fixing holes, and a surface handle needs none of either.

Why Buy Handles and Corner Guards Through SUPERB

  1. Load and fixing checked together: The handle is quoted against the mass of the case and the panel at the fixing points, which is where a 35 kg part gets ordered for a 120 kg case.
  2. Dish depth before the panel is cut: 8.5 mm and 10 mm dishes are stated, so the opening and the clearance behind it are known before the sheet metal shop starts.
  3. Corner radius matched: Guards are quoted by internal radius and leg count, so the guard sits flat on the corner that is already formed.
  4. Steel gauge for the duty: 0.8 mm to 2.0 mm parts are on the same range, so a mounted cabinet and a dropped case are not specified with the same guard.
  5. Fitted and lifted at assembly: The handle is set on the first unit and lifted with the ballast in place, because a rating on paper and a rating in the hand are different things.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Rubber Bumpers and Feet for Enclosure Support, Cable Glands and Strain Relief Bushings for Enclosure Entries, Fan Guards and Filter Screens for Enclosure Cooling, Standoffs Spacers and Mounting Hardware for Board Stacks, DIN and Circular Connectors for Panel Wiring, How to Verify a Drop in Replacement.