Contact Us
  • Home
  • COMPONENTS
  • PCB Card Guides and Board Retainers for Rack Cards

PCB Card Guides and Board Retainers for Rack Cards

A card guide holds a plug in board at both ends so the edge connector does not carry the weight of the card, and it sets the slot pitch in the rack. The snap in nylon guides here take a panel of 1.2 mm to 2.3 mm through a 4.6 mm hole, with card channels for 1.6 mm and 2.4 mm boards. Lengths run from 63.5 mm to 254 mm, and the deep channel version gives a 5.08 mm channel for high shock and vibration. Body materials are nylon 6/6 to UL94 V-2 and glass filled nylon to UL94 V-0, with a grounding clip option.
quote now

Product Specifications

Product Overview

A plug in card is held by its edge connector, and an edge connector is a contact spring, not a mechanical support. A card guide gives the card a second and third point of support at the two ends, so the connector is not taking the weight of a populated board or the leverage of a cable plugged into its face plate. The guide also sets the slot pitch, which is what decides how many cards go in a rack.

The Bivar COMP-O-GIDE is the industry standard snap in guide. The body is moulded nylon 6/6 to UL94 V-2, it snaps into a panel of 1.2 mm to 2.3 mm through a 4.6 mm hole, and it comes in 52 configurations from 2.5 inch to 8 inch in length. The channel is available for a 1/16 inch or a 3/32 inch board, and a stainless steel conductive insert is available on the same body where the card has to be grounded to the rack.

The GRIP-O-GIDE is the deep channel version, for a rack that sees shock and vibration. The channel is 0.200 inch deep instead of the standard depth, the body is moulded from a 10 percent glass filled nylon to UL94 V-0, and the same three channel widths cover 1/16, 3/32 and 1/8 inch boards. The deep channel holds the card over more of its edge, which is what stops a heavy card rocking in a mobile rack.

The channel width has to be read against the board thickness with the clearance in mind. A 1/16 inch board is 1.587 mm and the channel that takes it is nominally 2.03 mm, so there is about 0.4 mm of clearance on purpose. That clearance is what lets a card slide without binding on a humid day, and it is also what lets a card rattle in a rack with no end support. Where the card has to be held firmly, the answer is a deeper channel rather than a tighter one.

The panel thickness and the hole size are the figures that decide whether the guide stays put. A guide for a 1.2 mm to 2.3 mm panel snaps in by its pylons, and a panel outside that range either will not take the pylon or will not hold it. Two of the same guide on a panel at the thin end of the range will sit at slightly different angles, which is why the card goes in hard at one end and easy at the other.

Length and spacing are the last two figures. The guide length sets how much of the card edge is supported, and the spacing between two guides equals the guide body diameter plus the channel gap. On a rack where the pitch is already fixed by the connector positions, the guide is chosen to fit the pitch rather than the pitch being changed to fit the guide.

Key Specifications

ParameterValueApplies to
Body materialNylon 6/6, 10 percent glass filled nylonCOMP-O-GIDE, GRIP-O-GIDE
FlammabilityUL94 V-2, UL94 V-0COMP-O-GIDE, GRIP-O-GIDE
Panel thickness1.2 mm to 2.3 mmSnap in bodies
Snap in hole4.6 mmCOMP-O-GIDE
Card thickness1.6 mm (1/16), 2.4 mm (3/32), 3.2 mm (1/8)By channel
Channel depthStandard, 5.08 mm deep channelCOMP-O-GIDE, GRIP-O-GIDE
Guide length63.5 mm to 254 mmRange on this page
Card channel clearanceAbout 0.4 mm on a 1.6 mm cardStandard channel
Conductive insertStainless steel, optionalCOMP-O-GIDE, GRIP-O-GIDE
ColourNatural, blackBy part

Included Models and Order Codes

The rows below are the guides we quote most often. Length and mounting hole spacing are given per part because the spacing is what the panel is drilled to, and a dash means the maker does not publish that figure.

Part NumberSeriesLengthHole CentresCard ThicknessChannelNotes
SFS-250COMP-O-GIDE63.5 mm38.1 mm1.6 mmStandardNylon 6/6, UL94 V-2, natural
SFS-350COMP-O-GIDE88.9 mm63.5 mm1.6 mmStandardNylon 6/6, UL94 V-2
SFS-400COMP-O-GIDE101.6 mm76.2 mm1.6 mmStandardNylon 6/6, UL94 V-2
SFS-450COMP-O-GIDE114.3 mm76.2 mm1.6 mmStandardNylon 6/6, UL94 V-2
SFS-500COMP-O-GIDE127.0 mm101.6 mm1.6 mmStandardNylon 6/6, UL94 V-2
SFS-600COMP-O-GIDE152.4 mm127.0 mm1.6 mmStandardNylon 6/6, UL94 V-2
SFS-800COMP-O-GIDE203.2 mm177.8 mm1.6 mmStandardNylon 6/6, UL94 V-2
DC-450GRIP-O-GIDE114.3 mm-1.6 mmDeep, 5.08 mmGlass filled nylon, UL94 V-0
DC-500GRIP-O-GIDE127.0 mm-1.6 mmDeep, 5.08 mmGlass filled nylon, UL94 V-0
DC-600GRIP-O-GIDE152.4 mm-1.6 mmDeep, 5.08 mmGlass filled nylon, UL94 V-0
DC-800-102GRIP-O-GIDE203.2 mm-2.4 mmDeep, 2.59 mmFor a 3/32 inch card
N-500-2COMP-O-GIDE127.0 mm-1.6 mmNarrowNatural body, narrow channel
UDD-1000-CUniversal254.0 mm-1.6 mm to 2.0 mmWith grounding clipPress fit, panel 1.2 mm to 2.3 mm

Key Features

Card thickness in the part – 1.6 mm, 2.4 mm and 3.2 mm channels are separate parts, so a 3/32 inch card is not forced into a 1/16 inch guide.

Deep channel for vibration – The 5.08 mm channel holds the card over more of its edge, which is what keeps a heavy card from rocking in a mobile rack.

Panel range stated – The 1.2 mm to 2.3 mm panel range and the 4.6 mm hole are given, because a guide outside that range will not hold at the pylon.

Grounding clip option – A stainless steel insert is available on the same body, which is how a card is grounded to the rack without a separate strap.

Flame class per series – UL94 V-2 and V-0 bodies are both listed, so a rack with a V-0 requirement is not built on the standard body.

Lengths to 254 mm – The range covers a short module and a full depth card, with the mounting hole spacing given for each length.

Applications

These guides are used wherever a plug in board needs support beyond its edge connector, or where the slot pitch has to be fixed.

Rack and shelf systems – Two 127 mm guides per side support a plug in card at both ends, so the edge connector carries the signal and not the weight of the board.

Mobile and vehicle racks – A deep channel guide holds the card against shock and vibration, with the 5.08 mm channel keeping the board from rocking in the slot.

Instrument card cages – A 63.5 mm guide sets a close pitch between small modules, with the 4.6 mm snap in hole keeping the panel drilling simple.

A card guide sets the slot pitch in the rack, so the position is fixed on the SUPERB PCB before the chassis is machined. On the SUPERB PCBA route the guide is fitted after the board is populated, because a guide that is in place during handling catches on the parts beside the edge.

Sourcing and Cross-Reference

A card guide is bought by length and approved by card thickness. When a guide is replaced, the card thickness and the panel thickness are the two figures to check, because a guide for a 1.6 mm card in a rack that has moved to a 2.4 mm board will grip the edge and bow the card. We ask for both, and for the hole spacing already in the panel, before a length is quoted.

The second point is the channel depth. A standard channel is enough for a card that sits in a fixed rack, and the deep channel is used where the rack moves. The difference is not visible on a drawing, and a standard guide quoted into a mobile rack is a card that works loose over a year. The deep channel body is a different part number, and it is the one quoted where shock and vibration are stated.

The third point is the material and the flame class. A nylon 6/6 body to UL94 V-2 is the economical guide, and the 10 percent glass filled body to UL94 V-0 is used where the rack has to meet a V-0 requirement or where the guide is close to a heat source. On a rack with a conductive insert, the insert also gives the card a ground path, which is a different part number again. All three are quoted from the same range rather than substituted after the panel is drilled.

SUPERB Assembly presses the guide into the panel and checks that the card goes in without force, because a guide that is set at an angle loads the edge connector instead of supporting the board.

Q: Can you supply a 127 mm snap in card guide for a 1.6 mm card in a 1.5 mm panel, and confirm the hole size and the channel clearance before we drill?

A: Send the card thickness, the panel thickness and the depth of the rack. The SUPERB Tech desk quotes the guide with its channel depth and its snap in hole size, because a 1.6 mm card and a 2.4 mm card need different channels.

Why Buy Card Guides Through SUPERB

  1. Card thickness checked first: The channel is quoted against the board, so a 2.4 mm card is not forced into a 1.6 mm guide.
  2. Channel depth matched to the rack: Standard and deep channel bodies are kept apart, so a mobile rack is not built on a fixed rack guide.
  3. Hole and panel range stated: The 4.6 mm hole and the 1.2 mm to 2.3 mm panel range are given, so the panel is drilled once.
  4. Flame class and ground option: V-2, V-0 and the conductive insert are listed on the same range, so a requirement is met without changing supplier.
  5. Fitted square at assembly: The guide is pressed in and the card is checked for force, because a guide set at an angle loads the edge connector.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Card Edge Connectors for Backplanes and Riser Cards, Standoffs Spacers and Mounting Hardware for Board Stacks, DIN and Circular Connectors for Panel Wiring, Fan Guards and Filter Screens for Enclosure Cooling, How to Verify a Drop in Replacement.