EMI Shielding Cans and Contact Gaskets for RF Boards
Product Specifications
Product Overview
A shield can does one job: it keeps a radio stage from talking to the rest of the board, and keeps the rest of the board from talking to the radio stage. Everything else about it is a compromise between height, footprint, solderability and cost. The cans in this list are board level drawn parts, made from tin plated cold rolled steel or from nickel silver, and they are placed and reflowed with the other SMD parts. A one piece can is soldered straight to a ground ring on the board. A two piece can splits the part: a frame is soldered down, and a cover clips onto the frame, so the cover can be lifted for rework, for tuning or for a probe measurement without touching the solder joint.
Shielding effectiveness is set by the largest opening in the enclosure, not by the thickness of the wall. A 30 dB can with a 3 mm gap along one seam behaves like a 3 mm slot antenna, and at the frequency where that slot is half a wavelength the attenuation collapses. This is why the ground ring under the can matters more than the can itself: the pads have to be continuous under every wall, or stitched at a spacing well below a twentieth of a wavelength at the highest frequency the product has to pass. At 2.4 GHz a wavelength in air is about 125 mm, so a pad spacing of 6 mm or less is a safe starting point, and at 5.8 GHz that number halves again.
Height is the other hard limit. A can has to clear the tallest component inside it by enough that the lid does not press on a part after reflow, and it has to sit below whatever sits above the board. The sizes here cover that range: the small end is 10.2 x 6 x 3 mm for a single chip or a filter, the middle is 32.1 x 16.6 x 2.5 mm for a transceiver plus its matching network, and the large end is 32.3 x 23.8 x 3.7 mm, with a 4.7 mm frame where a taller inductor has to fit. A two piece part adds the thickness of the cover to the frame height, so the overall stack is the frame height plus the cover material, which is 0.2 mm on the drawn parts in this family.
Material is a second decision. Tin plated steel is the standard choice: it solders well, it is stiff enough that a thin wall stays flat, and it is the cheapest option per unit area. Nickel silver, which is a copper nickel zinc alloy, costs more but takes solder more readily after storage, resists corrosion better on a board that is washed or coated, and has a higher conductivity, so it is the usual pick for a can that has to work above 6 GHz or for a product that spends time in humid air. Both are offered in the same footprint in several sizes here, which means a material change does not force a board change.
The joint between a can and a chassis, or between a cover and a casting, cannot be soldered, and that is where the contact gasket comes in. Three families do that work. A copper beryllium finger strip is a spring: it is soldered or clipped to one surface and it deflects against the other, and its working height is quoted as a range rather than a single number. A conductive foam or elastomer gasket is a compressible cord that fills a groove and is compressed by roughly a third of its free height. A metal stamping or a woven mesh is used where the gap is wide and the shielding requirement is high, and the makers publish attenuation at 100 MHz and 1 GHz for those parts.
Two failures repeat often enough to be worth naming. The first is a can placed on a ground ring that is broken by a signal trace passing underneath a wall: the trace is fine electrically, but the can is now a resonator with a slot, and the emission at the slot frequency goes up rather than down. The second is a gasket selected on free height alone. A finger strip with a 6 mm free height and a recommended working range of 3.7 to 5.8 mm will be over compressed in a 3 mm gap and will take a set, and after a few closures it stops touching. The gap has to be measured with the cover closed, not with the parts on the bench.
Key Specifications
| Parameter | Value | Applies to |
|---|---|---|
| Can material | Tin plated cold rolled steel (CRS), or nickel silver | Per part number |
| Can construction | One piece drawn, or two piece with solderable frame and removable cover | Per part number |
| Mounting | SMD reflow on the can wall, or on the frame of a two piece part | Per part number |
| Can height | 2.0 mm to 4.7 mm in the sizes listed | Per part number |
| Footprint length | 10.2 mm to 32.9 mm | Per part number |
| Venting | Non vented, with perforated covers on request | Per part number |
| Packaging | Tray, or tape and reel on the cabinet parts | Per series |
| Operating temperature | -40 to +125 C on the cabinet parts | WE-SHC 36103205 |
| Storage and MSL | MSL 1, storage below 40 C and 75 percent RH | WE-SHC 36103205 |
| Finger material | Copper beryllium gold plated, or phosphor bronze nickel and tin plated | Per part number |
| Finger free height | 1.5 mm to 6 mm | Per part number |
| Recommended working height | 1.0 to 1.2 mm, up to 5.0 to 5.7 mm | Per part number |
| Surface resistance | 0.05 Ohm to 0.11 Ohm | Elastomer, stamping and woven parts |
| Attenuation | 80 dB at 100 MHz and 86 dB at 1 GHz on the gasket stamping | WE-LTS 34150209 |
| Gasket compression | About 30 percent of free height in normal use | EMC gaskets |
| Largest opening rule | The biggest aperture sets the leak, not the wall thickness | All parts |
Included Models and Order Codes
The rows below are the drawn cans and two piece sets we quote most often, with the footprint and height taken from the maker drawing. Add 0.2 mm to the frame height to get the overall height of a two piece set on the drawn parts. A dash means the maker does not publish that figure.
| Part Number | Type | Dimensions L x W x H | Material | Mount | Notes |
|---|---|---|---|---|---|
| MS102-10S-NS | One piece can | 10.2 x 6 x 3 mm | Nickel silver | SMD | Smallest size in the list, for a single filter or a clock |
| MS320-10S | One piece can | 32 x 11.3 x 2 mm | Tin plated steel (CRS) | SMD | Low profile, non vented |
| MS320-10S-NS | One piece can | 32 x 11.3 x 2 mm | Nickel silver | SMD | Same footprint as the CRS part, for wash and coating |
| MS321-10S | One piece can | 32.1 x 16.6 x 2.5 mm | Tin plated steel (CRS) | SMD | Transceiver plus matching network |
| MS323-10S | One piece can | 32.3 x 23.8 x 3.7 mm | Tin plated steel (CRS) | SMD | Largest one piece size in the list |
| MS323-10S-NS | One piece can | 32.3 x 23.8 x 3.7 mm | Nickel silver | SMD | Higher conductivity, corrosion resistant |
| MS323-10F | Two piece frame | 32.3 x 23.8 x 3.7 mm | Tin plated steel (CRS) | SMD | Soldered frame, takes the MS323-10C cover |
| MS323-10C | Two piece cover | 32.9 x 24.4 x 4 mm | Tin plated steel (CRS) | Clips to frame | 0.2 mm material, cover only |
| MS323-10CP | Two piece perforated cover | 32.9 x 24.4 x 4 mm | Tin plated steel (CRS) | Clips to frame | Vented cover for a part that runs warm |
| MS323-20F | Two piece tall frame | 32.3 x 23.8 x 4.7 mm | Tin plated steel (CRS) | SMD | Extra 1 mm of headroom for a taller inductor |
| 36103205 | Two piece cabinet | 21 x 21 x 3 mm outer, 20 x 20 mm inner | Tin plated steel | SMT frame, removable cover | Tape and reel, -40 to +125 C, MSL 1 |
| 36900000 | Cabinet clip | 0.8 x 1.27 mm | Steel | SMT | Retaining clip for a cabinet cover |
Contact Gaskets and Fingers for Chassis and Cover Joints
These parts close the joint a can cannot reach: a cover to a casting, a module to a panel, or a cable entry to a wall. Working height is the range the part is meant to be compressed into when the two surfaces are closed, and it is the figure to check against the real gap.
| Part Number | Type | Size W x H | Working Height | Material | Electrical and Notes |
|---|---|---|---|---|---|
| 331031321515 | SMT contact finger | 1.5 x 1.5 mm | 1.0 to 1.2 mm | Copper beryllium, gold plated | Low height for a thin cover |
| 331031271520 | SMT contact finger | 1.5 x 2 mm | 1.6 to 1.7 mm | Copper beryllium, gold plated | Narrow finger for a tight seam |
| 331171302030 | SMT contact finger | 2 x 3 mm | 2.5 to 2.7 mm | Copper beryllium, gold plated | General purpose mid height |
| 331171302035 | SMT contact finger | 2 x 3.5 mm | 3.0 to 3.2 mm | Copper beryllium, gold plated | Same base, taller travel |
| 331221602040 | SMT contact finger | 2 x 4 mm | 5.0 to 5.7 mm | Copper beryllium, gold plated | Long travel for a cover with a gasket groove |
| 331246501860 | SMT contact finger | 2.2 x 6 mm | 3.7 to 5.8 mm | Phosphor bronze, nickel and tin plated | Tin solder area, wide working range |
| 38401102 | Conductive elastomer gasket | 1.384 x 1.73 mm | Compressed in a groove | Silicone with conductive filler | Surface resistance 0.05 Ohm |
| 34150209 | Conductive gasket stamping | 2 x 15 mm | Clamped or clipped | Metal stamping | 80 dB at 100 MHz, 86 dB at 1 GHz, 0.08 Ohm |
| 302020299 | Conductive foam gasket | 2 x 2 mm | 1.4 to 1.6 mm | Polyether urethane foam, conductive wrap | Surface resistance 0.08 Ohm, halogen free |
| 30502 | Woven mesh gasket | 2 x 0.13 mm | Wraps a cable of 1 to 5 mm | Nickel copper plated glass fibre | 45 dB at 100 MHz, 29 dB at 1 GHz, 0.11 Ohm |
Key Features
Footprint and height stated – Every row gives the drawn length, width and height from the maker drawing, so a can can be checked against the pads and the tallest part before it is ordered.
One piece and two piece – A one piece can is the lowest cost route; a frame plus cover costs more but comes off for rework, tuning and probe access without a reflow.
Steel and nickel silver in one footprint – Several sizes are offered in both materials, so a move to nickel silver for wash, coating or higher frequency does not change the ground ring.
Working height on the fingers – The finger table gives the range the part is meant to sit in, not only its free height, because over compression is the usual reason a gasket stops contacting.
Measured attenuation where published – The stamping and woven parts carry maker figures at 100 MHz and 1 GHz, and the surface resistance of every gasket family is listed.
Gasket and can quoted together – A can with no gasket, or a gasket with the wrong working height, is a joint that leaks; the two are quoted as a pair against the same gap.
Applications
These parts cover the shielding work on radio boards, wireless modules and instrument enclosures.
RF front end and PA stages – A 32.3 x 23.8 x 3.7 mm can covers a power amplifier, its bias network and the output filter, and a two piece version lets the output match be trimmed after the first article.
Wireless modules and clock circuits – A 32 x 11.3 x 2 mm low profile can fits over a module, a crystal and a DC-DC converter on a board where the stack height is fixed by the enclosure.
Instrument covers and castings – A copper beryllium finger strip or a foam gasket closes the joint between a cover and a chassis, where the gap varies with the casting and cannot be soldered.
The can and the gasket are placed on the SUPERB PCB during the same build as the RF stage they cover, and the same team handles the SUPERB PCBA run, so the ground pads and the frame footprint are checked against the can before reflow.
Sourcing and Cross-Reference
Shield cans are ordered by footprint, and the footprint is what makes a replacement hard. Length, width, height and wall angle all have to match, because the ground ring on the board is fixed. Where a size has gone out of a catalogue, the nearest drawn size is usually still made by another tool, and a 0.3 mm difference in length is absorbed by the ground ring if the pads were drawn with any margin at all. We ask for the old part number or the pad drawing and quote against the pad dimensions, not against the can alone.
Nickel silver parts are the common gap in a shortage. A customer who has been buying tin plated steel for a board that is now washed or conformally coated often finds the steel part is not the one on the approved list any more, and the nickel silver version of the same footprint is. Because the two share a footprint in several sizes, the change is a material change on the drawing rather than a board change, which is a much shorter approval path.
Gaskets are the part most often bought late, after the enclosure is fixed, and by then the gap is what it is. A finger strip is picked from the working height range, not from the free height, and a foam gasket is picked from the compression the closure can apply. Where the gap is wide and the attenuation requirement is high, a metal stamping gives 80 dB at 100 MHz in a 15 mm width, which no foam part of the same size reaches. We quote the gasket against the measured gap and the frequency, and state the compression the part will see.
SUPERB Assembly keeps the cans in trays until the paste is printed, because a can that has been dropped has a lid that no longer sits flat and a seam that no longer touches the ground ring.
Q: Can you supply a shield can that fits an existing PCB footprint, and the matching gasket for the same enclosure gap?
A: Send the footprint, the height available under the cover and the frequency that has to be contained; the SUPERB Tech desk quotes the can and the contact gasket as a pair so the two cannot arrive with different working heights.
Why Buy Shield Cans and Gaskets Through SUPERB
- Pad drawing first: The old part number or the ground ring drawing is checked before a size is quoted, so the replacement lands on the pads that already exist.
- Can and gasket as a pair: The two are quoted against the same gap and the same footprint, which removes the usual mismatch between a can height and a finger working range.
- Material choice kept open: Tin plated steel and nickel silver versions of the same footprint are both listed, so a wash or coating change does not force a board change.
- Attenuation stated where published: The gasket rows carry maker figures at 100 MHz and 1 GHz instead of a generic claim, so the part can be compared with the requirement.
- Placed in the same build: The can, the frame and the gasket are handled in the same assembly step as the RF stage, so a lifted cover or a crushed finger is caught at first article.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: EMI Feedthrough Filters and Filter Connectors, Heat Sinks and Thermal Interface Pads, RF Coaxial Connectors and Adapters, Board to Board and FPC Connectors, MLCC and Ceramic Capacitors.