Contact Us
  • Home
  • COMPONENTS
  • Battery Holders and Coin Cell Retainers for Backup Power

Battery Holders and Coin Cell Retainers for Backup Power

A backup cell holder is chosen on cell size, mounting side and whether the cell has to be replaced in the field. Through hole retainers on this page cover 12 to 23 mm coin cells, and surface mount parts cover 12 and 20 mm. Cylindrical holders add AA and 18650 cells with polarised contacts and snap in retention for wave soldering. Contact material and plating are listed per part, because that is what sets contact resistance over life.
quote now

Product Specifications

Product Overview

A coin cell retainer looks like a trivial part until a unit comes back from the field with a flat cell that was never making contact. The three things that decide whether it works are the cell diameter, the mounting side and the retention force. A through hole retainer sits on the component side with legs that survive wave soldering; a surface mount retainer is placed on the same side as the rest of the paste and has to keep its spring after reflow. Both are on this page because a board team usually needs one of each across a product family.

For cylindrical cells the holder does more work. An AA or 18650 cell is inserted and removed many times, so the contacts have to be polarised, the body has to be keyed against reverse insertion, and the retention has to hold through vibration. Keystone builds these bodies in UL 94 V-0 nylon with 0.30 mm stainless steel contacts and either tin nickel or gold flash plating. The 18650 parts are the ones we quote most for handheld instruments, telemetry units and portable test gear.

The electrical side is small but not zero. Contact resistance of a plated phosphor bronze spring is a few tens of milliohms when new, and it rises if the plating is worn or the spring has taken a set. For a coin cell feeding a real time clock the current is microamps and this does not matter; for a 18650 feeding a heater or a radio during transmit it does, and the holder becomes part of the supply budget. We list the contact material so this can be checked rather than assumed.

Key Specifications

ParameterValueApplies to
Cell sizes, coin12 mm, 16 mm, 20 mm, 23 mm, 24 mmRetainers on this page
Cell sizes, cylindricalAA, 18350, 18650Holders on this page
MountingThrough hole, surface mount, PC pin contactPer part number
Contact material0.25 mm phosphor bronze, tin nickel plateCoin cell retainers
Contact material, cylindrical0.30 mm stainless steel, tin nickel or gold flashAA and 18650 holders
Body materialNylon 46 or PBT, UL 94 V-0Per part number
Operating temperature-40 to 105 CSurface mount retainers
RetentionSnap in legs for wave solder, or spring clipPer part number
PolarityMarked on body, keyed contactCylindrical holders
Tape and reel500 or 1000 pieces per reel, 44 mm tapeSurface mount retainers

Included Models and Order Codes

The rows below are the retainers and holders we quote most often, listed with the cell each one takes and the mounting style. Dimensions are the maker body outline, since the board cut out follows the part rather than the other way round. Where a holder is offered in more than one plating, the plated version is the one quoted by default.

Part NumberCellMountingBody SizeNotes
300012 mm coin, CR1216 to CR1225Surface mount13.2 x 6.7 mm, 3.2 mm highTape and reel available as 3000TR
300112 mm coin, CR1216 to CR1225Through hole13.2 x 7.1 mmTwo legs, phosphor bronze, tin nickel
301316 mm coin, CR1616 to CR1632Through hole16.7 x 6.4 mmSuits 1.6 mm board
300220 mm coin, CR2016 to CR2032Surface mount30.7 x 19.8 mm, 4.0 mm high500 per reel, wave solder compatible
303420 mm coin, CR2025 and CR2032Surface mount23.1 x 16.1 mm, 4.1 mm highCompact outline, nickel plate option
300320 mm coin, CR2016 to CR2032Through hole21.1 x 9.4 mmStandard retainer for backup rails
300523 mm coin, CR2320 to CR2330Through hole23.9 x 9.4 mmSame leg pattern as 3003
1015AA, single cellThrough holePer maker drawingDual spring contact, UL 94 V-0 nylon
1024AA, single cellSurface mountPer maker drawingReflow compatible, cover 1024C
104218650, single cellSurface mountPer maker drawingPolarised version 1042P, gold flash
104318650, single cellThrough holePer maker drawingPolarised version 1043P, tin nickel
92AA and 17 to 19 mm cellsPC pin contactPer maker drawingSingle contact clip, mates with a second clip

Key Features

Cell size stated first – Every row names the cells it takes, so a 20 mm retainer is not ordered for a 16 mm cell by mistake.

Mounting side separated – Through hole and surface mount parts are listed apart, because the board side decides the assembly sequence.

Contact material named – Phosphor bronze with tin nickel, or stainless steel with gold flash, is given per part so contact resistance can be estimated.

Retention for wave solder – Snap in legs hold the retainer flat during wave soldering, which is the failure mode on tall coin cell parts.

Polarity keyed – Cylindrical holders are marked and keyed, so a cell cannot be inserted the wrong way in a unit that is closed at the bench.

Tape and reel options – Surface mount retainers are offered on reel where the line runs a placer rather than a short run by hand.

Applications

These parts hold backup and primary cells in instruments, telemetry units, timers and portable test gear.

RTC and memory backup – A 20 mm retainer holds a CR2032 that keeps a real time clock and a small SRAM alive, and the through hole version survives the wave solder that the rest of the board sees.

Handheld instruments – An AA or 18650 holder with a polarised contact takes the cell that the user replaces, and the keyed body stops a reversed cell from damaging the regulator.

Telemetry and remote units – A compact 12 mm retainer on the component side leaves the bottom of the board free for a sealed enclosure face, which is why the 3034 outline is quoted for small nodes.

The holder is placed on the SUPERB PCB alongside the clock and the regulator, and its height is checked against the enclosure before the SUPERB PCBA is released.

Sourcing and Cross-Reference

A holder request usually arrives as a photo of the old part. The useful facts are the cell, the mounting side and the board hole pattern, and the hole pattern is what decides whether a substitute fits without a board change. We ask for the board drawing or the footprint rather than the photo, then match the maker part and confirm the plating.

Plating matters on parts that are inserted often. Tin nickel is the standard finish and is fine for a cell replaced once a year; gold flash is used where the contact has to stay low resistance after many cycles or in a humid enclosure. Both are quoted with the same body, so the choice is visible and can be made on the actual use rather than on price alone.

SUPERB Assembly checks contact spring tension on the first article and after the wave, because a flattened spring is not visible once the cell is in.

Q: Can you supply a holder that fits our existing board holes without a layout change?

A: SUPERB Tech quotes the holder with the cell it takes and the plating, so a repeat order cannot arrive with a different finish.

Why Buy Battery Holders Through SUPERB

  1. Footprint checked first: The board hole pattern is matched before a part is quoted, so a replacement holder does not force a board change.
  2. Cell and side confirmed: Cell size and mounting side are agreed in writing, which is where most wrong holder orders start.
  3. Plating chosen for the use: Tin nickel and gold flash are both quoted, so the finish follows the number of insertions rather than habit.
  4. Reel or bulk: Surface mount parts are offered on reel or in bulk, matching the line rather than the pack size we happen to hold.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Supercapacitors for RTC Hold Up, Real Time Clock ICs and Timing Buffers, Battery Chargers and Fuel Gauges, Pin to Pin Cross Reference.