Contact Us
  • Home
  • COMPONENTS
  • EMI Feedthrough Filters and Filter Connectors for Shielding

EMI Feedthrough Filters and Filter Connectors for Shielding

A feedthrough filter removes noise at the point where a wire crosses a shield, which is the only place the return path is still short. Chip three terminal parts on this page cover 0.1 to 2.2 uF at 2 to 4 A in 0603 and 0805. Threaded filters cover 500 pF to 10 nF at 10 to 20 A, with the thread and voltage stated per part. Capacitance alone does not decide the part; the current rating and the thread decide whether it can be fitted.
quote now

Product Specifications

Product Overview

Noise leaves or enters an enclosure along a conductor, and the shield only works if that conductor is filtered where it passes through the wall. A feedthrough filter does exactly that: the conductor goes through a capacitor electrode, so the noise sees a short path to the chassis while the signal or supply current passes through. The result is a low pass filter with an insertion loss that rises with frequency, and the shape of that curve is set by capacitance and by the inductance of the through path.

Two families cover most builds. On the board, a three terminal chip filter such as the Murata NFM series puts the capacitor between input and output with the ground in the middle, which gives far more loss above 200 MHz than a plain capacitor of the same value. At a panel, a threaded filter such as the Tusonix 4400 series is bolted into the wall and the wire is soldered or pushed through it, so the chassis is the ground and the filter is the shield's own wall.

The number that is missed most often is current. A 0.1 uF chip filter in 0603 is a 2 A part, and the 1 uF and 2.2 uF versions in 0805 are 4 A parts at lower voltage, so a filter chosen only on capacitance can be run at twice its rating. On the threaded side, a 10 nF part at 50 V and 10 A and a 10 nF part at 250 V and 20 A look the same in a list and are not interchangeable. Every row on this page carries the current, the voltage and the thread for that reason.

Key Specifications

ParameterValueApplies to
Filter typeThree terminal chip, threaded feedthrough, bushing mountPer part number
Capacitance500 pF to 2.2 uFPer part number
Rated current2 A, 4 A, 10 A, 20 APer part number
Rated voltage6.3 V to 250 VPer part number
Case size, chip0603, 0805NFM series
Thread, panel parts4-40, M3 x 0.5, 12-28Tusonix parts
Insertion loss15 dB at 100 MHz on 500 pF part4400-001
Insulation resistance200 to 1000 M ohm minimumPer part number
Operating temperature-55 to 125 C on most parts, -40 to 85 C on 1 uF and abovePer part number
MountingSolder pad, or threaded bushing with solder terminalsPer part number

Included Models and Order Codes

The rows below are the chip and threaded filters we quote most for supply and signal lines crossing a shield. Current and voltage are given for the exact part, because the same capacitance appears at two ratings in both families. Insertion loss is quoted where the maker publishes a figure at a stated frequency.

Part NumberTypeCapacitanceCurrent and VoltageNotes
NFM18PC104R1C3Chip, 0603, three terminal0.1 uF2 A, 16 V1000 M ohm, -55 to 125 C
NFM21PC104R1E3Chip, 0805, three terminal0.1 uF2 A, 25 V1000 M ohm, -55 to 125 C
NFM21PC224R1C3Chip, 0805, three terminal0.22 uF2 A, 16 V1000 M ohm, -55 to 125 C
NFM21PC474R1C3Chip, 0805, three terminal0.47 uF2 A, 16 V1000 M ohm, -55 to 125 C
NFM21PC105B1A3Chip, 0805, three terminal1.0 uF4 A, 10 V500 M ohm, -40 to 85 C
NFM21PC225B0J3Chip, 0805, three terminal2.2 uF4 A, 6.3 V200 M ohm, -40 to 85 C
4400-001Threaded feedthrough, 4-40500 pF10 A, 200 V15 dB at 100 MHz, 3.96 mm body
4400-089LFThreaded feedthrough, M3 x 0.510 nF10 A, 50 VC circuit, lead terminals both sides
2499-003-X7W0-103ZBushing feedthrough, 12-2810 nF20 A, 250 VX7W dielectric, -55 to 125 C

Key Features

Three terminal structure – The chip parts put the ground between input and output, which gives more loss above 200 MHz than a two terminal capacitor of the same value.

Current stated per part – A 2 A 0603 and a 4 A 0805 are separated, because a filter chosen on capacitance alone can be run past its rating.

Thread listed – 4-40, M3 and 12-28 threads are given, so a panel filter is not ordered against the wrong hole.

Voltage on every row – 6.3 V to 250 V covers logic rails and 48 V or mains side wiring in the same table.

Insertion loss where published – The 500 pF threaded part carries a 15 dB figure at 100 MHz, so the loss can be compared with a measured plot.

Tape and reel for chips – The 0603 and 0805 parts are reel parts, so they run on the same placer as the rest of the passives.

Applications

These filters are used where a supply or signal line crosses a shield, on instrument panels, radio housings and industrial controllers.

Panel feedthrough on a shielded enclosure – A 10 nF threaded filter at 10 A passes the supply into a radio housing while the chassis carries the return, which keeps cable borne noise off the inside of the shield.

Board level rail filtering – A 0.1 uF 0603 filter on a sensor supply pin removes noise above 200 MHz that a plain capacitor of the same value lets through.

Instrument and medical housings – A 20 A 250 V bushing filter is used where a heater or a lamp line leaves a metal case and the harness has to stay filtered at the wall.

The chip filter sits on the SUPERB PCB at the connector, and the threaded part is fitted to the panel that the SUPERB PCBA is built into.

Sourcing and Cross-Reference

Feedthrough filters are ordered on capacitance, current, voltage and thread, and the thread is the one that cannot be changed at the bench. A 4-40 body will not fit a 12-28 hole, and an M3 part will not seal against a 4-40 nut, so we confirm the panel hole and the wall thickness before quoting.

On the chip side the risk is different. The 1 uF and 2.2 uF parts are 4 A devices at 6.3 to 10 V, and they are often specified where a 25 V rail was intended. We check the rail voltage against the part and quote the 0.1 uF 25 V version where the headroom is needed, rather than let the capacitance decide.

SUPERB Assembly checks the filter body is seated against the chassis wall and that no solder has bridged the ground electrode on the first article.

Q: Can you supply a feedthrough filter with the same thread and panel hole as the one already fitted?

A: SUPERB Tech keeps the capacitance and the thread on the same line item, so a repeat panel build cannot arrive with a filter that will not fit the hole.

Why Buy EMI Feedthrough Filters Through SUPERB

  1. Thread and hole confirmed: The panel thread and wall thickness are matched before quoting, because those cannot be changed on the bench.
  2. Current and voltage checked: Every part is quoted with its own rating, so a 2 A chip filter is not used where 4 A flows.
  3. Insertion loss on the table: Loss figures are given where the maker publishes them, so the filter can be compared with a measurement.
  4. Chip and panel parts together: Both ends of the shield are covered from one quote, which keeps the board and the panel filter consistent.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Ferrite Beads and EMI Filters, Common Mode Chokes and Power Inductors, TVS and ESD Protection Diodes, BOM Shortage Recovery.