USB Type-C and Power Delivery Controllers for Portable Devices Sink, source and dual role controllers for one or two USB Type-C ports. Power delivery contracts up to 20 V at 5 A, which is 100 W on a single port. Integrated 25 milliohm power switches, or a gate driver for an external FET. I2C and GPIO control for a host that has to read the contract and the cable state.
Power over Ethernet PD Controllers for Powered Devices PD interface controllers for IEEE 802.3af, 802.3at and 802.3bt powered devices. PD power from 13 W on type 1 up to 71.3 W on class 8, with 5 event classification. Integrated hotswap FETs from 0.3 ohm, or external FETs for the highest efficiency. Flyback, forward and buck converter controllers on the same die as the interface.
VCO and PLL Synthesizer ICs for Radio and Instrument LO Fractional N and integer N synthesizers with integrated VCO covering 35 MHz to 32 GHz. Phase detector rates to 400 MHz and fractional moduli to 39 bits. RMS jitter from 38 fs to 0.3 ps depending on the part and the carrier. IF VCO ICs from 45 MHz to 650 MHz with differential output in SOT-23-6.
Constant Current LED Driver ICs for Indicator and Backlight Boost, buck and linear constant current topologies for LED strings. Output current from 10 mA on a linear regulator up to 5 A on a buck controller. PWM dimming ratios to 10,000 to 1 and analog dimming for camera-safe light. Single channel drivers and 24 channel serial sinks in one supply line.
Real Time Clock ICs and Timing Buffers for Data Logging Temperature compensated real time clocks at 2 ppm from 0 C to 40 C. Standard I2C real time clocks with battery backup, alarms and SRAM. Clock buffers with 2, 4 and 8 LVCMOS outputs and 25 ps output skew. SOIC, TSSOP and chip scale packages for logging and metering boards.
Supervisory and Watchdog Timer ICs for MCU and FPGA Rails Reset supervisors with fixed and adjustable thresholds from 0.4 V to 5 V. Watchdog timers with window and standard timeout behaviour. Threshold accuracy from 0.5 to 2.5 percent over temperature. Manual reset inputs, power good outputs and open drain or push pull reset.
Load Switches and Hot Swap Controllers for Board Power Sequencing Integrated load switches from 1 V to 5.5 V and 1.5 A to 6 A. On resistance from 16 milliohm to 90 milliohm with quiescent current in microamps. Hot swap controllers from 2.9 V to 80 V with programmable current limit and fault timer. Adjustable slew rate, reverse current blocking and power good outputs.
Common Mode Chokes and Power Inductors for Supply Filtering Two line common mode chokes in 0805, 1206 and 1210 sizes, 90 ohm to 2.2 kohm at 100 MHz. Rated current from 200 mA to 1 A with DCR from 0.19 ohm to 0.9 ohm. Shielded power inductors from 1 uH to 33 uH for buck and boost stages. Automotive grade and commercial grade options with reel packing.
Isolated DC-DC Modules and Brick Converters for Instrument Boards Encapsulated modules from 1 W to 20 W in SIP, DIP, SMD and 1 x 1 inch footprints. Isolation from 1 kVDC to 5.2 kVDC, single and dual outputs. Wide 2 to 1 and 4 to 1 input ranges for 12 V, 24 V and 48 V rails. Brick converters for higher power floating and intermediate bus rails.
Battery Chargers and Fuel Gauges for Portable Instruments Linear chargers from 500 mA to 1.5 A with power path and input current limit. Switch mode chargers up to 5 A with I2C control and 93 percent efficiency. Fuel gauges using voltage model or coulomb counting, with and without a sense resistor. Protection, termination and status outputs in SOT-23, QFN and SON packages.
DACs and Voltage References for Control Loops Voltage output DACs from 12 to 16 bit, single channel up to 16 channels. Unipolar 0 V to 5 V and bipolar plus or minus 10 V output ranges with internal references. Series references from 2.048 V to 5 V at 0.02 percent initial error and 2 ppm per degree C. SPI and I2C interfaces with daisy chain and clear to zero on fault.
16-Bit SAR ADCs for Instrumentation and Control Simultaneous sampling parts with 4 to 8 channels at 200 kSPS to 1 MSPS. Multiplexed 16 bit SAR from 250 kSPS to 1 MSPS in MSOP, LFCSP and TSSOP. True bipolar plus and minus 10 V inputs with clamp protection and 1 MOhm impedance. On chip 2.5 V or 4.096 V reference options and SPI with daisy chain.
RF Gain Blocks and Low Noise Amplifiers for Receive Front Ends Cascadable gain blocks from 30 MHz to 6 GHz with up to 45 dBm output intercept GNSS low noise amplifiers at 0.55 dB and 0.8 dB noise figure for receiver front ends Wideband MMIC low noise amplifiers covering 0.3 GHz to 20 GHz in surface mount packages Gain, noise figure and supply current confirmed against the exact order code
Logic Level Shifters and IO Expanders for Mixed Voltage Boards Auto direction translators for open-drain buses at up to 2 Mbps and push-pull lines at 24 Mbps Direction controlled transceivers with 420 Mbps translation and 24 mA drive at 3.3 V I2C and SMBus IO expanders adding 8 or 16 ports with an interrupt output Supply range, direction control and channel count confirmed against the exact suffix
TVS and ESD Protection Diodes for Telecom and Industrial Interfaces Steering diode arrays from 0.3 pF for high speed pairs, surge suppressors from 130 W to 1500 W Asymmetrical 12 V and 7 V RS-485 parts and 24 V bidirectional CAN protectors IEC 61000-4-2 level 4 arrays with IEC 61000-4-4 and IEC 61000-4-5 surge ratings Order code, reel suffix and batch data confirmed against the exact part number
RF Transceiver ICs for Software-Defined Radio and Telemetry Wideband RF agile transceivers from 70 MHz to 6 GHz with 2x2 and 1x1 channels Tunable channel bandwidth from under 200 kHz to 56 MHz for SDR platforms Sub 1 GHz transceivers for telemetry, metering and remote control links Long range spread spectrum parts with 148 dBm sensitivity and 20 dBm output
BLDC and Stepper Motor Driver ICs for Motion Control Three phase gate drivers for 6 V to 60 V motor stages with external FETs Integrated FET drivers with 2.5 A half bridge capability and on board LDO Sensorless and sensored trapezoidal drivers that need no control firmware Stepper and dual DC motor drivers for positioning stages
ECG and Biopotential Analog Front Ends for Patient Monitors 24 bit simultaneous sampling front ends for ECG and EEG channels Low power parts from 335 uW per channel for portable and wearable monitors Built in right leg drive, lead off detection and respiration measurement Parts referenced to AAMI EC11 and IEC 60601 requirements
Digital Isolators for Industrial and Medical Interfaces Dual and quad channel isolators at 25 Mbps and above for control interfaces Reinforced parts rated 5000 V rms with up to 12.8 kV surge capability Isolated USB 2.0 full and low speed front end for instruments and monitors Ultra low power channels for loop powered and battery backed boards
RS-485 and RS-232 Transceiver Chips for Industrial Interfaces RS-485 and RS-422 transceivers from 250 kbps to 26 Mbps in 5 V and 3.3 V versions RS-232 line drivers and receivers with integrated charge pumps from 3 V to 5.5 V Isolated RS-485 parts with integrated DC to DC conversion and 15 kV ESD Auto direction parts for two wire buses without a control pin
LED Indicators and Optocouplers for Status and Isolation 0603 and 0805 chip LEDs plus 5 mm through hole indicators for board status Phototransistor optocouplers from 50 percent CTR for signalling and feedback 10 MBd logic gate couplers for digital isolation and line receiving Phototriac couplers for AC switching with zero cross options
Crystal Units and TCXO Oscillators for Frequency References 32.768 kHz tuning fork crystals for real time clocks and battery backed time 8 MHz to 54 MHz surface mount crystals at 10 ppm with matched load capacitance TCXO parts at 0.5 ppm for GNSS, LTE and RF references MEMS oscillators from 1 MHz to 110 MHz where shock and vibration matter
AT32 MCUs for Flight Controller and Motor Control Boards AT32 Cortex-M4F parts from 120 MHz to 288 MHz with FPU and DSP Up to 4032 KB flash and 512 KB SRAM for large control firmware Advanced timers with dead time generation for three-phase motor drive All order codes on this page are grouped into one line for sourcing
PWM Controller ICs for Switching Power Supplies Current mode controllers in eight pins, up to 500 kHz with pulse by pulse limiting Push pull and half bridge controllers with adjustable dead time and soft start PFC front end controllers for EN61000-3-2 compliant supplies above 350 W All models on this page are grouped into one part for easy sourcing
Comparator Chips for Threshold and Level Detection General purpose open collector comparators in single, dual and quad packages Micro power comparators with an internal reference for battery boards Response times from 560 ns to 60 us with adjustable hysteresis All models on this page are grouped into one part for easy sourcing
Current Sense Amplifiers and Shunt Monitors for Power Measurement Analog, digital and isolated current sense families for one shunt design Common-mode range from 26 V up to 110 V with fixed gains of 20 to 500 V/V I2C current and power monitors with 12-bit and 16-bit resolution All models on this page are grouped into one part for easy sourcing
Ethernet PHY and Switch Chips for Industrial Networking 10/100 and gigabit PHYs with MII, RMII, GMII and RGMII interfaces Three port, five port and seven port switch devices for embedded boards Industrial and automotive temperature grades with LinkMD diagnostics All models on this page are grouped into one part for easy sourcing
LDO Linear Regulators for Low Noise Power Rails Ultralow noise LDOs from 0.8 uV rms for RF and instrumentation rails High voltage parts up to 36 V input for industrial and telecom boards Fixed and adjustable outputs from 150 mA to 1.5 A load current All models on this page are grouped into one part for easy sourcing
eMMC and NAND Flash Storage for Industrial Controllers Managed eMMC from 4 GB to 128 GB in 153 ball packages Raw SLC NAND from 1 Gb to 8 Gb in TSOP-48 for legacy designs SPI NAND from 1 Gb to 2 Gb in small packages for firmware images All models on this page are grouped into one part for easy sourcing
FPGA and CPLD Chips for Industrial and Telecom Boards FPGA families from 2,000 to 326,000 logic cells and elements CPLDs from 64 to 570 macrocells for glue logic and interface expansion BGA, QFP and QFN packages with commercial, industrial and automotive grades All models on this page are grouped into one part for easy sourcing
Magnetometer and Compass Sensors for Heading Reference Three axis magnetometers from 8 gauss to 50 gauss full scale range Hall, AMR and magneto inductive types with 16 bit to 20 bit output Heading accuracy from 0.5 degree for AMR parts and 18 bit resolution All models on this page are grouped into one part for easy sourcing
Barometric Pressure and Altitude Sensors for Drones and Navigation Absolute pressure sensors from 10 mbar to 1260 hPa coverage Altitude resolution from about 1 m down to 10 cm for variometers I2C and SPI interfaces in LGA packages for flight controller boards All models on this page are grouped into one part for easy sourcing
N-Channel and P-Channel Power MOSFETs for Motor Drive and Power Conversion N channel parts from 30 V to 500 V, 4 mOhm to 0.85 Ohm on resistance P channel complements from 55 V to 100 V for high side and load switching Logic level, standard and avalanche rated versions for motor drive All models on this page are grouped into one part for easy sourcing
Gate Driver Chips for Motor and Power Stage Control High side and low side gate drivers in 2 A, 2.5 A and 4 A classes Half bridge, dual channel and three phase configurations up to 600 V Bootstrap and isolated versions for MOSFET and IGBT power stages All models on this page are grouped into one part for easy sourcing
Clock Generators and Frequency Up-Converters for Optical Line Cards Clock generation and distribution parts for optical line cards and transponders 156.25 MHz and 106.25 MHz references, dual PLL generators, up-conversion to 900 MHz, fan-out All models listed below are combined into this single product for easy sourcing Samples, build quantities, alternatives and cross reference are supported
SFP and SFP+ Digital Diagnostics Controllers for Optical Transceivers Digital diagnostics and control ICs for SFP, SFP+, video SFP and PON modules APC loops with temperature look up tables, SFF-8472 monitoring and maskable laser shutdown All models listed below are combined into this single product for easy sourcing Samples, build quantities, alternatives and cross reference are supported
ADI Power Management ICs for Optical Modules and Instrument Boards Low noise power parts for optical module and instrument board rails Low Vin and 20 V low noise LDOs, configurable synchronous bucks, a buck plus LDO micro PMU All models listed below are combined into this single product for easy sourcing Samples, build quantities, alternatives and cross reference are supported
Precision Operational Amplifiers for Sensor Signal Chains Precision operational amplifiers for sensor signal conditioning and instrumentation front ends Low offset, low drift and low noise dual and quad parts from ADI and Texas Instruments All models listed below are combined into this single product for easy sourcing Samples, build quantities, alternatives and cross reference are supported
CAN Bus Transceivers and Controllers for Automotive and Industrial Networks CAN bus transceivers and stand-alone CAN controllers for automotive and industrial networks Isolated 2500 V and 5000 V parts, 3.3 V and 5 V transceivers, SPI CAN controllers All models listed below are combined into this single product for easy sourcing Samples, build quantities, alternatives and cross reference are supported
STM32F103 Mainstream MCUs for Industrial Control Boards STMicroelectronics STM32F103 mainstream Cortex-M3 microcontrollers for industrial control boards 64 kB to 1 MB Flash in LQFP48, LQFP64, LQFP100 and LQFP144 packages, 72 MHz, 2.0 V to 3.6 V All models listed below are combined into this single product for easy sourcing Samples, build quantities, alternatives and cross reference are supported