LDO Linear Regulators for Low Noise Power Rails
Product Specifications
Product Overview
A switching regulator is efficient but its output is never quiet enough for an analog front end. The usual answer is a low dropout regulator after the switcher, and the numbers that decide whether it works are output noise in the band of interest, power supply rejection at the switching frequency and its harmonics, and dropout voltage at the load current actually required.
The parts on this page are chosen along two axes. The ultralow noise family, at 0.8 uV to 6.5 uV rms from 10 Hz to 100 kHz, is used for PLL and VCO supplies, ADC and DAC references, low level sensor amplifiers and RF gain stages. The wider input voltage family, up to 36 V, is used where the regulator has to survive an industrial rail, an automotive load dump or a 24 V bus and still keep the analog domain clean.
All models are grouped into this single product, so a board can be quoted with the whole analog power tree: the switcher, the post regulators, the reference and the passive parts that set the output voltage. Tell us the input rail, the load current, the noise limit in microvolts and the dropout available, and the part can be checked against the rejection curve rather than picked by output current alone.
Key Specifications
| Parameter | Ultralow Noise Parts | High Voltage and General Purpose Parts |
|---|---|---|
| Output noise | 0.8 uV rms to 6.5 uV rms from 10 Hz to 100 kHz | 9 uV rms to 40 uV rms, or noise not specified |
| Input voltage | 1.8 V to 20 V, or 5.5 V for the small portable parts | Up to 36 V, 40 V and 20 V families |
| Output current | 200 mA, 300 mA, 500 mA and 800 mA | 150 mA to 1.5 A |
| Dropout voltage | 260 mV to 350 mV at full load | 300 mV to 1.3 V depending on the current |
| PSRR | 76 dB to 82 dB at 1 MHz for the ultralow noise parts | 55 dB to 70 dB at 100 kHz |
| Output voltage | Fixed 1.2 V to 5 V, or adjustable with a single resistor | Fixed and adjustable versions |
| Packages | DFN, MSOP with PowerPAD, VQFN 5 x 5 mm, SOT-23-5 | SOT-223, TO-220, DD-PAK, SOIC-8 |
| Temperature range | -40 C to 125 C junction | -40 C to 125 C junction |
Included Models and Order Codes
The table lists the regulator classes most often requested for analog, RF and sensor rails. Send the complete order code including the package and the output voltage option and we confirm availability against that exact string.
| Model | Input Voltage | Output Current | Noise and PSRR | Package | Notes |
|---|---|---|---|---|---|
| TPS7A4701RGWR | 3 V to 36 V | 1 A | 4 uV rms, 82 dB at 100 Hz | 20 pin VQFN, 5 x 5 mm | Adjustable output to 34 V, dropout 307 mV at 1 A |
| TPS7A4700RGWR | 3 V to 36 V | 1 A | 4 uV rms, 82 dB at 100 Hz | 20 pin VQFN, 5 x 5 mm | Output set by board wiring, no external feedback parts |
| TPS7A4901DGNR | 3 V to 36 V | 150 mA | Low noise for instrumentation rails | MSOP-8 with PowerPAD | High voltage small load rail behind a switcher |
| TPS7A20 | 1.6 V to 6 V | 300 mA | Ultralow noise for sensor and camera rails | Small surface mount | Low quiescent current for always on rails |
| LT3045EDD | 1.8 V to 20 V | 500 mA | 0.8 uV rms, 2 nV per root Hz at 10 kHz, 76 dB at 1 MHz | DFN-12, 3 x 3 mm | Dropout 260 mV, parallelable for lower noise |
| LT3045IMSE | 1.8 V to 20 V | 500 mA | 0.8 uV rms, 76 dB at 1 MHz | MSOP-12 | Industrial temperature version of the same die |
| LT3042 | 1.8 V to 20 V | 200 mA | 0.8 uV rms, 79 dB at 1 MHz | DFN and MSOP, 3 x 3 mm | Dropout 350 mV, programmable current limit |
| LT1963AEQ | 2.1 V to 20 V | 1.5 A | Low noise, fast transient response | DD-PAK, TO-220 | High current rail for instrument supplies |
| ADM7150ARDZ-3.3 | 4.5 V to 16 V | 800 mA | Ultralow noise for RF and instrumentation | SOIC-8 | Fixed output versions for analog rails |
| ADP7142ARDZ-5.0 | 2.7 V to 40 V | 200 mA | Low noise with wide input range | SOIC-8 with exposed pad | Industrial rail with a large input excursion |
| LP5907MFX-3.3 | 2.2 V to 5.5 V | 250 mA | Ultralow noise for portable and sensor boards | SOT-23-5 | Very low quiescent current |
| LP2985-3.3 | 2.5 V to 16 V | 150 mA | Low noise for small analog rails | SOT-23-5 | Long established part for legacy boards |
| MIC5205-3.3YM5 | 2.5 V to 16 V | 150 mA | Low noise, low dropout | SOT-23-5 | Pin compatible with the common 150 mA footprint |
| LM1117MPX-3.3 | Up to 15 V | 800 mA | General purpose, no noise specification | SOT-223 | Workhorse rail for digital and interface sections |
| AMS1117-3.3 | Up to 15 V | 1 A | General purpose, no noise specification | SOT-223 | Widely used in industrial boards and modules |
| NCP1117ST33T3G | Up to 20 V | 1 A | General purpose, no noise specification | SOT-223 | Second source for the 1 A SOT-223 footprint |
Key Features
Noise Stated In Microvolts – Output noise from 0.8 uV rms to 6.5 uV rms over 10 Hz to 100 kHz, so the rail can be checked against the resolution of the converter it supplies.
Rejection At The Switching Frequency – PSRR figures at 100 kHz and 1 MHz are what decide whether a switcher can be cleaned up by a post regulator, and they are quoted with the current path in mind.
Wide Input For Industrial Rails – 36 V and 40 V input parts for 24 V buses and industrial supplies, with the dropout voltage at the real load current rather than at a nominal 100 mA.
Dropout Against The Rail – Dropout of 260 mV to 350 mV on the ultralow noise parts keeps headroom available when the input is a battery or a rail that sags under load.
Parallelable And Programmable – Current reference based parts can be paralleled to lower the noise further or to spread the heat, and the output can be programmed with one resistor.
Packages That Match The Board – SOT-23-5 for small rails, MSOP with a thermal pad, 5 x 5 mm VQFN for high current and SOT-223 for the general purpose parts.
Second Sources For Legacy Boards – Where the original regulator is obsolete, the nearest part in the same package and pin out is quoted with the noise and dropout differences stated.
Applications
Rails where these regulators are specified: An analog rail is normally quoted as one item covering the regulator, its capacitors and the SUPERB PCB and SUPERB PCBA work we support for the same board.
RF And Microwave Sections – Supply rails for PLL and VCO circuits, low noise amplifiers and mixers, where the phase noise of the source depends on the noise of the rail.
Data Converter References – Analog rails for ADC and DAC circuits in instrumentation, ultrasound and test equipment, where the converter cannot do better than its supply.
Sensor And Instrument Front Ends – Low level bridge and photodiode amplifiers where a rail in the tens of microvolts is the difference between a usable and an unusable signal chain.
Industrial 24 V And Telecom Rails – Post regulators behind a 24 V or 48 V bus, and industrial boards that need a wide input part with an exposed pad for heat.
Sourcing and Cross-Reference
Regulator families are often replaced by a part that fits the footprint but not the noise requirement, and the effect only shows up in the measurement on the final instrument. Two candidates can share a package and a pin out while differing by more than 20 dB in rejection at 1 MHz, so the comparison has to be made on the curves.
We check noise in the band that matters to the application, rejection at the switcher frequency, dropout at the load current in use, and the stability requirement for the output capacitor. Where a substitute needs a different capacitor value or a feed forward part, that is stated with the quote. Where the original is obsolete, the nearest live part in the same package family is offered first.
Where the board is built in volume, SUPERB Assembly support covers the SMT build of the analog section.
Q: Can you supply a low noise alternative for a discontinued LDO regulator?
A: Yes. Send the order code, the package and the quantity and the SUPERB Tech sales team will reply with availability and the nearest replacement with the noise difference stated.
Why Source LDO Regulators from Superb Automation?
- Specialised Sourcing Focus: Power, RF and mixed signal devices for industrial, telecom, medical and defence builds, compared on the figures the analog rail depends on.
- Hard To Find And Obsolete Parts: Regulators that leave production while instruments stay in service, sourced with the lifecycle status and the nearest equivalent stated up front.
- Cross Reference Support: Noise in the relevant band, rejection at the switching frequency, dropout and capacitor stability differences listed with the quote.
- Stock And Build Quantities: Prototype quantities, repair quantities and volume orders are all welcome, with batch information stated per line.
- BOM Kitting: The regulator, its capacitors and the resistors that set the output can be quoted together for the whole analog power tree.
- Reply With Evidence: Documents, batch marking and the condition of the parts are stated on the quote before the order is placed.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: BOM Shortage Recovery, Power Management ICs, Step-Down DC-DC Converter Chips for Industrial Power Rails, Precision Operational Amplifiers for Sensor Signal Chains.