Contact Us
  • Home
  • COMPONENTS
  • BLDC and Stepper Motor Driver ICs for Motion Control

BLDC and Stepper Motor Driver ICs for Motion Control

Three phase gate drivers for 6 V to 60 V motor stages with external FETs Integrated FET drivers with 2.5 A half bridge capability and on board LDO Sensorless and sensored trapezoidal drivers that need no control firmware Stepper and dual DC motor drivers for positioning stages
quote now

Product Specifications

Product Overview

A motor stage fails at the interface between the controller and the winding. The gate driver has to deliver enough peak current to switch the FETs before the next PWM edge, the current sense amplifier has to see the shunt without picking up the switching node, and the dead time has to be long enough to avoid shoot through without distorting the current waveform. Those numbers are decided by the driver, not by the controller firmware.

This page groups the motor drivers we supply into three levels. The gate driver level covers 6 V to 60 V stages with external FETs, up to 1.7 A source and 2.3 A sink peak gate current, programmable dead time from 50 ns to 500 ns, dual current shunt amplifiers and, on the wider part, an integrated buck regulator that powers the controller from the motor rail. The second level is the integrated bridge, where three half bridges with 2.5 A peak and 1.75 A rms per channel sit in one body and each bridge brings its own ground pin out for independent shunt sensing.

The third level is the fixed function driver, which is the shortest path to a spinning motor. The sensored part implements trapezoidal commutation with three analog hall comparators in hardware and supports up to 200 kHz PWM without any control code, while the sensorless part runs its own trapezoidal algorithm with startup under 50 ms from 4.5 V to 35 V. For positioning stages the stepper and dual DC drivers cover the lower current range with integrated protection. The MOSFETs used with the gate driver level parts are listed on our power MOSFET page.

Key Specifications

ParameterThree Phase Gate DriverIntegrated Bridge DriverFixed Function Driver
Motor rail6 V to 60 V8 V to 60 V4.5 V to 35 V, 40 V absolute maximum
Output currentGate drive 1.7 A source and 2.3 A sink peak, external FET sets the load current2.5 A peak and 1.75 A rms per half bridge with a heatsinked boardSet by the integrated FETs and the package
On resistanceExternal FET decidesIntegrated N-channel MOSFET bridges without gate resistors95 mOhm to 100 mOhm combined high side and low side
Current sensingDual current shunt amplifiers with external referenceDedicated ground pin per bridge for independent shuntsCycle by cycle current limit option
Dead timeProgrammable from 50 ns to 500 ns, 5 ns matching between the sidesSet internallyHandled internally
Switching frequencyUp to 200 kHz with 30 mA total average gate driveUp to the thermal limit of the boardUp to 200 kHz PWM input
Control interfaceSix PWM inputs or three PWM inputs with SPI configurationThree PWM inputs, independent half bridge controlPWM input, analog voltage or serial command
ProtectionOvercurrent, undervoltage, thermal and gate drive fault reportingOvercurrent, thermal shutdown, undervoltage lockoutOvercurrent, thermal warning and shutdown, motor lock detection

Included Models and Order Codes

The table lists the driver part codes most often requested for drone, robotics and industrial motion boards. Send the complete order code including the package and we confirm availability against that string.

Part NumberLevelMotor RailCurrentPackageNotes
DRV8301Three phase gate driver with current sense and buck regulator6 V to 60 V1.7 A source and 2.3 A sink peak gate driveHTSSOP with thermal padDead time 50 ns to 500 ns, dual shunt amplifiers, buck for the controller rail
DRV8302Three phase gate driver with current sense6 V to 60 VPeak gate drive for external FETsHTSSOP with thermal padGate driver level part for high current three phase stages
DRV8305Three phase gate driver with current sense and regulatorsGate driver levelThree phase gate drive for external FETsCompact surface mountAdds regulator and protection features for smaller drives
DRV8353RThree phase gate driver with current sense and buck regulatorHigher voltage driver stageThree phase gate drive for external FETsSurface mount with thermal padGate driver level part with integrated current sense amplifiers
DRV8313Integrated bridge driver, three half bridges8 V to 60 V2.5 A peak and 1.75 A rms per half bridgePower pad surface mountBuilt in 3.3 V 10 mA LDO, uncommitted comparator for current limit, sleep mode
MCT8316ZSensored trapezoidal driver with integrated FETs8 V to 40 V classSet by the integrated bridgeSurface mountThree analog hall comparators, up to 200 kHz PWM, no control firmware needed
MCT8316ASensorless trapezoidal driver with integrated FETs4.5 V to 35 V, 40 V absolute maximumIntegrated 95 mOhm high side plus low sideSurface mountStartup under 50 ms, deceleration under 150 ms, buck regulator and LDO on board
L6234Three phase driver in BCDmultipower technologyMotor supply up to 52 V classThree half bridges with DMOS power stagePower DIP or surface mountMixed technology body with the logic and the power stage on one die
TB6612FNGDual DC motor driver15 V maximum1.2 A average and 3.2 A peak per channelSSOP240.5 Ohm combined on resistance, clockwise, counter clockwise, brake and stop modes
DRV8825Stepper motor driver with integrated FETsStepper supply classMicrostepping up to 1/32 stepSurface mount with thermal padIntegrated indexer, used on positioning and dispensing stages
A4988Stepper motor driver with translatorStepper supply classMicrostepping up to 1/16 stepSurface mount with thermal padClassic stepper driver for low cost positioning stages
TMC2209Stepper driver with quiet mode and diagnosticsStepper supply classMicrostepping with stealth chopCompact surface mountSerial configuration and stall detection for sensorless homing

Key Features

Gate drive current stated – 1.7 A source and 2.3 A sink peak on the gate driver level parts, which sets how fast the external FETs can be switched

Programmable dead time – 50 ns to 500 ns with 5 ns matching between the high side and low side paths, so shoot through margin and waveform distortion can be traded off

Current sense built in – dual shunt amplifiers with an external reference on the gate driver parts, and a dedicated ground pin per bridge on the integrated parts for independent sensing

Controller rail on the same part – an integrated buck regulator on the wider gate drivers powers the controller from the motor rail instead of adding a separate supply

Fixed function parts with no firmware – sensored and sensorless trapezoidal drivers spin the motor without control code, which shortens the path from board to first rotation

Protection set included – overcurrent, undervoltage, thermal shutdown and fault reporting on one pin across the families

Applications

The parts are supplied for the boards below. A motor stage is normally quoted with the SUPERB PCB and SUPERB PCBA work we support for the same board, so the driver, the MOSFETs, the shunts and the assembly come from one source.

Drone and robotics drives – three phase stages on ESC and joint controller boards, using the gate driver level parts when the FETs are chosen for the current and the integrated parts when board space is tight

Industrial pumps and fans – sensorless trapezoidal drives with integrated FETs where a fixed function part removes the need for motor control firmware

Positioning and dispensing stages – stepper and dual DC drivers with microstepping for stages that move to a commanded position

Sourcing and Cross-Reference

Motor driver availability is decided by the package and the current rating, not by the function. A 2.5 A integrated part cannot take the place of a gate driver with external FETs, and a part without a thermal pad cannot be fitted to a land pattern that expects one.

We confirm availability against the complete order code including package, and where a code is short we quote the nearest option with the current rating, gate drive strength and dead time programming difference stated in writing, so the thermal and switching margins can be rechecked before the driver is fitted. The MOSFETs and gate resistors for the same stage can be quoted on the same line.

SUPERB Assembly support covers the SMT build of the power section where the boards are assembled in volume.

Q: Can you supply pin compatible motor drivers for a discontinued part number?

A: Yes. Send the order code, the package and the quantity and the SUPERB Tech sales team will confirm availability and the nearest driver with the current rating difference stated.

Why Buy From Us

  1. Package and thermal path confirmed: the quoted part is checked against the land pattern and the thermal pad the board expects
  2. Current and gate drive stated: peak gate current, bridge current and on resistance are given so the stage margin can be recalculated
  3. Dead time and protection documented: programmable dead time range and protection set are listed with the quotation for switching stages
  4. Power stage sourced as one line: driver, MOSFETs, shunts and the gate parts can be quoted together so the motor stage arrives complete

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Power Management ICs, PWM Controller ICs for Switching Power Supplies, N-Channel and P-Channel Power MOSFETs, BOM Shortage Recovery.