Contact Us
  • Home
  • COMPONENTS
  • Supervisory and Watchdog Timer ICs for MCU and FPGA Rails

Supervisory and Watchdog Timer ICs for MCU and FPGA Rails

Reset supervisors with fixed and adjustable thresholds from 0.4 V to 5 V. Watchdog timers with window and standard timeout behaviour. Threshold accuracy from 0.5 to 2.5 percent over temperature. Manual reset inputs, power good outputs and open drain or push pull reset.
quote now

Product Specifications

Product Overview

A supervisor does one thing: it holds the processor in reset until the rail is high enough to be trusted, and it asserts reset again before the rail falls far enough for the processor to execute from undefined memory. The threshold accuracy is the number that matters, because a 5 percent tolerance on a 3.3 V rail moves the trip point by 165 mV, which is often the difference between a clean reset and a processor that runs at 3.0 V and corrupts its own non volatile memory. The second number is the reset timeout, the delay after the rail is good, which has to be longer than the oscillator start up and the internal regulator ramp of the device being supervised.

The simple three pin parts cover most boards: the MAX809 and MAX810 in SOT-23 with a threshold trimmed at test, an active low or active high push pull output and a 140 ms minimum reset pulse, at around 12 microamps of supply current; the ADM803 adds an open drain output for wired or reset; the TPS3808 adds a programmable delay from 1.25 ms to 10 s with 0.5 percent threshold accuracy and 2.4 microamps of quiescent current. These are the parts that sit next to the processor and are forgotten once the board works.

The watchdog group covers the failure that a supervisor cannot see: a processor whose rail is perfect and whose firmware has stopped. The MAX6369 and the TPS3823 combine a supply monitor with a watchdog input that must be toggled inside a timeout window, and assert reset when it is not. Window watchdogs, as on the TPS3700 window comparator and the STWD100, also catch a firmware loop that toggles too fast, which a simple watchdog accepts as healthy. On FPGA rails the same parts supervise the core and the IO supply separately, because the core is often the last rail to come up and the first to sag.

Key Specifications

ParameterReset supervisorsWatchdog and window supervisors
Threshold range0.4 V to 5 V fixed, or adjustable with an external dividerFixed and adjustable, plus a window comparator option
Threshold accuracy0.5 percent on the TPS3808, 1.5 to 2.5 percent on the three pin parts1.5 to 2.5 percent over temperature
Reset timeout140 ms to 240 ms fixed, 1.25 ms to 10 s programmableProgrammable, with a separate watchdog timeout
WatchdogNoneStandard timeout or window timeout
Manual resetOptional on the MAX823 and TPS3808Common, with debounce
Output typePush pull or open drain, active low and active high versionsPush pull and open drain, some parts with both polarity outputs
Supply current2.4 microamps on the TPS3808, around 12 microamps on the MAX809Tens of microamps
PackageSOT-23-3, SC70, SOT-23-6SOT-23-5, SOT-23-6, MSOP-8

Included Models and Order Codes

The table lists the supervisor and watchdog order codes most often quoted for processor and FPGA rails. State the rail voltage and the tolerance, the reset polarity, the delay needed after the rail is good and whether a watchdog is required, and the order code is confirmed with packing.

Part NumberFunctionThresholdReset DelayOutputPackage
MAX809SEUR+TThree pin reset supervisor2.93 V140 ms minimumActive low push pullSOT-23-3
MAX810SEUR+TThree pin reset supervisor, opposite polarity2.93 V140 ms minimumActive high push pullSOT-23-3
MAX823TEUK+TSupervisor with watchdog and manual reset3.08 V150 msActive low push pullSOT-23-5
MAX6369KA+TWatchdog timer with adjustable timeoutNot a supply monitorAdjustableOpen drainSOT-23-8
TPS3808G33DBVRSupervisor with programmable delay3.07 V fixed, 0.5 percent accuracy1.25 ms to 10 sActive low open drainSOT-23-6
TPS3823-33DBVRSupervisor with watchdog2.93 V200 msActive low push pullSOT-23-5
TPS3700DDCRWindow comparator for over and under voltageAdjustable from 0.4 VProgrammableOpen drain, two outputsSOT-23-6
ADM803SAKSZ-REEL7Three pin supervisor with open drain reset2.93 V240 msActive low open drainSC70-3
STWD100NYWY3FWatchdog timer with enableNot a supply monitor1.6 s typicalOpen drainSOT-23-5
LTC2912IMS8-1#PBFDual supply monitor with adjustable delayAdjustableAdjustableOpen drainMSOP-8

Key Features

Threshold accuracy over temperature – 0.5 percent on the TPS3808 and 1.5 to 2.5 percent on the three pin parts, which is the number that decides how much of the rail tolerance is left for the regulator.

Programmable reset delay – a capacitor on the CT pin sets the delay from 1.25 ms to 10 s, so the reset can outlast the oscillator and the internal regulator of the processor.

Both output polarities – active low and active high versions of the same part number exist for processors and peripherals that expect different reset sense.

Open drain for wired or – several supervisors on one board can share a single reset line without a logic gate.

Watchdog with a window – a window watchdog also catches firmware that toggles the input too quickly, which a standard watchdog treats as a healthy processor.

Microamp supply current – 2.4 microamps on the TPS3808 keeps the supervisor from being the load that decides the standby budget of a battery instrument.

Applications

These parts are quoted for processor and FPGA rails, typically where: A reset tree is normally quoted with the SUPERB PCB and SUPERB PCBA work we support for the same board, so the supervisors, the watchdog and the assembly come from one source.

Industrial controllers and meters – a 3.3 V rail and a firmware image that must not run below the flash write threshold, with a watchdog to recover from a locked loop in the field.

FPGA and SoC boards – core, IO and auxiliary rails come up in sequence and each one needs its own supervisor with a delay that matches its ramp.

Battery and remote equipment – the supervisor has to work down to a low supply voltage and draw microamps, because the board spends most of its life asleep.

Sourcing and Cross-Reference

Supervisors look interchangeable and are not. The same SOT-23-3 body carries thresholds from 2.5 V to 4.6 V, active low and active high outputs, push pull and open drain, and reset timeouts that differ by a factor of three. A substitution made on the family name changes the point at which the processor is released, which is a field failure rather than a bench one. We quote the full order code with the threshold and the output type spelled out on the confirmation.

The second trap is the reset delay against the processor. A 140 ms pulse is right for a crystal that starts in 5 ms and wrong for a module whose internal regulator takes 300 ms, and the symptom is an intermittent boot that only appears cold. Where the delay has to change we quote the adjustable part in the same footprint rather than a fixed part from another family, so the capacitor value is the only change on the board.

For volume builds, SUPERB Assembly support covers the SMT assembly of the processor and reset sections.

Q: Can you confirm the reset threshold and output polarity for the exact supervisor order code?

A: Yes. Send the complete order code with the threshold and the output polarity, and the SUPERB Tech sales team will confirm availability and the nearest part in the same package.

Why Buyers Source Supervisors Through SUPERB

  1. Threshold and polarity on the quote: the two fields that decide whether a part is interchangeable are written on the confirmation, not left to the family name.
  2. Footprint compatible alternatives: where a threshold has to change, the adjustable part in the same package is proposed first, so the board does not have to be re-laid.
  3. Watchdog and supervisor from one line: parts that supervise the rail and parts that supervise the firmware are quoted together, so the reset tree is specified with the parts that will be fitted.
  4. Batch traceability: date code and lot per reel are recorded, which matters when a boot failure has to be tied to a specific build.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Power management ICs, STM32F103 MCUs, FPGA and CPLD, LDO linear regulators, Pin to pin cross reference.