Contact Us
  • Home
  • COMPONENTS
  • VCO and PLL Synthesizer ICs for Radio and Instrument LO

VCO and PLL Synthesizer ICs for Radio and Instrument LO

Fractional N and integer N synthesizers with integrated VCO covering 35 MHz to 32 GHz. Phase detector rates to 400 MHz and fractional moduli to 39 bits. RMS jitter from 38 fs to 0.3 ps depending on the part and the carrier. IF VCO ICs from 45 MHz to 650 MHz with differential output in SOT-23-6.
quote now

Product Specifications

Product Overview

A local oscillator is judged by three numbers, and they pull against each other. The tuning range sets what the radio can cover, the phase noise at a given offset sets how close two carriers can sit before they interfere, and the reference spurs set what a receiver hears when it tunes past a strong signal. A synthesizer with an integrated VCO wins on size and on the number of sensitive nodes, because the loop from the charge pump to the varactor stays inside the package. It loses on the freedom to choose a high Q resonator, which is why an external VCO is still used above 20 GHz and in instruments where the phase noise budget is set by a dielectric resonator.

The wideband parts on this page cover the range in steps of about a decade each. The ADF4351 is the general purpose entry: 35 MHz to 4.4 GHz from a fundamental VCO running at 2.2 GHz to 4.4 GHz and a bank of dividers down to 64, with a 32 MHz phase detector, fractional or integer operation, 0.3 ps typical rms jitter and an in band phase noise of about 100 dBc per Hz at 3 kHz offset from a 2.1 GHz carrier. The LMX2594 raises the phase detector to 400 MHz in integer mode and 300 MHz in fractional mode, reaches 10 MHz to 15 GHz with no doubler, and quotes a figure of merit of 236 dBc per Hz with 45 fs of rms jitter at 7.5 GHz. The ADF4371 goes to 32 GHz through a 4 GHz to 8 GHz VCO, a doubler and two quadrupler paths, with a 39 bit fractional modulus, a 250 MHz phase detector and 38 fs of integrated jitter, in a 7 by 7 mm LGA.

The rest of the range fills the gaps that matter in practice. The LMX2572 covers 12.5 MHz to 6.4 GHz from 75 mA at 3.3 V, which is the part for a battery powered radio or a remote unit where the synthesizer is on all the time, and it still quotes 106 dBc per Hz at 100 kHz offset from a 6.4 GHz carrier. The MAX2870 spans 23.5 MHz to 6 GHz with dual outputs that are programmable from minus 4 to plus 5 dBm, a 105 MHz phase detector in integer mode and 0.25 ps of rms jitter. Below that, the MAX2605 to MAX2609 family is not a synthesizer at all but the oscillator inside one: a Colpitts core with the varactor and the feedback capacitors on the die, one external inductor to set the frequency, a differential output buffer and a phase noise figure that goes from 117 dBc per Hz at 100 kHz in the 45 MHz to 70 MHz band to 93 dBc per Hz in the 500 MHz to 650 MHz band. For a fixed channel radio or a cheap instrument front end, that is the whole VCO in a SOT-23-6.

Key Specifications

ParameterWideband synthesizers with VCOIF VCO ICs
Output range10 MHz to 32 GHz depending on part45 MHz to 650 MHz in five bands
Fundamental VCO2.2 GHz to 8 GHz, with dividers and multipliersColpitts core with on chip varactor
Phase detectorUp to 250 MHz, 300 MHz or 400 MHz by partNot applicable, no divider
Fractional modulusUp to 39 bitsNot applicable
Phase noise106 to 131 dBc per Hz at 100 kHz offset93 to 117 dBc per Hz at 100 kHz offset
Jitter38 fs to 0.3 ps rmsSet by the loop filter and the reference
Supply3.0 V to 3.6 V, 5 V VCO rail on the 32 GHz part2.7 V to 5.5 V
Control3 wire or 4 wire serial, lock detect outputAnalog tune voltage, 0.4 V to 2.4 V

Included Models and Order Codes

The table lists the synthesizer and VCO order codes most often quoted for radio, radar and instrument local oscillators. State the output range, the channel step, the phase noise required at a named offset, the reference frequency and the supply, and the part and its grade are confirmed with the packing.

Part NumberFunctionOutput RangeSupplyKey Noise FigurePackage
ADF4351BCPZFractional and integer N synthesizer with VCO35 MHz to 4.4 GHz3.0 V to 3.6 V0.3 ps rms jitter, 131 dBc per Hz at 100 kHz from 4.4 GHzLFCSP-32
ADF4371BCCZMicrowave synthesizer with VCO, doubler and quadrupler62.5 MHz to 32 GHz3.3 V, 5 V VCO rail38 fs rms jitter from 1 kHz to 100 MHzLGA-48, 7 by 7 mm
LMX2594RHATWideband synthesizer with VCO, no doubler10 MHz to 15 GHz3.3 V45 fs rms at 7.5 GHz, 110 dBc per Hz at 100 kHz from 15 GHzVQFN-40
LMX2572RHATLow power wideband synthesizer with VCO12.5 MHz to 6.4 GHz3.0 V to 3.5 V, 75 mA106 dBc per Hz at 100 kHz from 6.4 GHzVQFN-40
MAX2870ETJ+Fractional and integer N synthesizer with VCO, dual output23.5 MHz to 6 GHz3.0 V to 3.6 V0.25 ps rms jitter, minus 4 to plus 5 dBm per outputTQFN-32, 5 by 5 mm
MAX2605EUT-TIF VCO with differential buffer45 MHz to 70 MHz2.7 V to 5.5 V, 1.9 mA117 dBc per Hz at 100 kHzSOT-23-6
MAX2606EUT-TIF VCO with differential buffer70 MHz to 150 MHz2.7 V to 5.5 V, 2.1 mA112 dBc per Hz at 100 kHzSOT-23-6
MAX2607EUT-TIF VCO with differential buffer150 MHz to 300 MHz2.7 V to 5.5 V, 2.1 mA107 dBc per Hz at 100 kHzSOT-23-6
MAX2608EUT-TIF VCO with differential buffer300 MHz to 500 MHz2.7 V to 5.5 V, 2.7 mA100 dBc per Hz at 100 kHzSOT-23-6
MAX2609EUT-TIF VCO with differential buffer500 MHz to 650 MHz2.7 V to 5.5 V, 3.6 mA93 dBc per Hz at 100 kHzSOT-23-6

Key Features

Integrated VCO – the resonator, the varactor and the output divider are on the die, so the loop stays short and the board does not need a shielded can around the oscillator.

Phase detector rate – a 250 MHz or 400 MHz phase detector allows a wider loop bandwidth, which is what shortens lock time in a frequency hopping radio.

Fractional modulus – a 39 bit modulus on the 32 GHz part gives steps far below one hertz at the output, so a channel plan can use round numbers without a second reference.

Phase synchronisation – the LMX parts support SYSREF and multi device phase alignment, which is what a phased array or a multi converter board needs at power up.

Low current options – 75 mA at 3.3 V on the 6.4 GHz part keeps a synthesizer inside the budget of a battery powered remote unit.

VCO in a six pin package – the IF VCO family needs one external inductor and one bypass capacitor, which puts a stable oscillator on a board the size of a postage stamp.

Applications

These parts are quoted for radios, radar front ends and instruments, typically where: An LO board is normally quoted with the SUPERB PCB and SUPERB PCBA work we support for the same assembly, so the synthesizer, the loop filter and the shielding arrive together.

Radio and telemetry local oscillators – a narrowband link needs a fixed channel with low close in noise, and an integer N loop with a clean reference still gives the best spurious performance per milliamp.

Test and measurement – a signal generator or a spectrum analyser needs a wideband source with fine steps, and a 15 GHz or 32 GHz synthesizer replaces a YIG tuned oscillator in the lower bands.

Radar and phased arrays – a frequency modulated source with a linear ramp, plus phase alignment between channels, is what a small radar or an array module is built around.

Sourcing and Cross-Reference

Synthesizers are long life parts on short life processes. A radio platform can stay in production for a decade, while the synthesizer that was qualified on it moves to a smaller package or to a new process, and the replacement changes the register map, the charge pump range or the VCO band count. That is why we quote the exact order code with the temperature grade and hold the lot, and why a proposed alternative is compared on phase detector rate, VCO range and loop filter values rather than on the family name.

The second issue is the loop filter and the reference, which are outside the part and are where most of the noise is decided. A synthesizer quoted without the reference oscillator, the loop filter values and the charge pump setting is only half a specification, so the parts here are quoted together with the crystal or TCXO that sets the phase detector rate, and the VCO ICs with the inductor that sets the band.

For volume builds, SUPERB Assembly support covers the SMT assembly and the shielded section of the LO board.

Q: Can you supply obsolete synthesizer parts with the same register map as the original?

A: Yes. Send the complete order code, the output range, the phase noise at a named offset and the reference frequency, and the SUPERB Tech sales team will confirm availability and the loop parts that match.

Why Buyers Source Frequency Parts Through SUPERB

  1. Part number level quoting: the suffix that carries the temperature grade and the package is confirmed per line, because a synthesizer in the wrong grade will not hold lock over the temperature range.
  2. Reference and loop parts together: the TCXO, the loop filter and the synthesizer for one LO are quoted as a set, so the phase noise budget uses the parts that will be fitted.
  3. Long life supply: parts that the supplier has moved to end of life are held with their date code, which keeps a radio platform in production while a replacement is qualified.
  4. Board support: where the LO board is built in volume, the assembly and test of the shielded section is handled by the same team that supplies the parts.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Frequency converters and sources, Clock generators, Crystal units and TCXO, RF PLL control board, RF component sourcing.