Contact Us
  • Home
  • COMPONENTS
  • LED Indicators and Optocouplers for Status and Isolation

LED Indicators and Optocouplers for Status and Isolation

0603 and 0805 chip LEDs plus 5 mm through hole indicators for board status Phototransistor optocouplers from 50 percent CTR for signalling and feedback 10 MBd logic gate couplers for digital isolation and line receiving Phototriac couplers for AC switching with zero cross options
quote now

Product Specifications

Product Overview

Indication and isolation parts are the cheapest items on a board and the ones that stop a build. A status LED has to match the viewing angle and brightness the front panel needs, and an optocoupler has to match a current transfer ratio bin, an isolation rating and a speed grade. Replacing a coupler with a part from a different CTR bin, or a 10 MBd coupler with a 1 MBd part, changes the circuit even when the package is identical.

This page groups the parts we supply along those lines. For indication the chip LEDs cover 0603 and 0805 sizes with water clear lenses and defined dominant wavelength, and the 5 mm through hole parts cover the panel indicators with a 50 degree viewing angle. For signal isolation the phototransistor couplers run from 50 percent minimum current transfer ratio with 80 V collector-emitter rating and 5000 V rms isolation, which covers feedback in switching supplies, signal transfer between domains and low speed digital isolation.

For fast digital interfaces the logic gate couplers give 10 MBd with an open collector or open drain output and common mode transient immunity from 5 kV per microsecond to 15 kV per microsecond, which is what a fieldbus, a line receiver or an isolated conversion interface needs. Where an AC load has to be switched from a logic signal, the phototriac couplers provide 5000 V rms isolation in the DIP-6 package with zero cross and random phase options. The isolation devices that carry the same job on the board side are listed on our isolator page.

Key Specifications

ParameterChip and Panel LEDsPhototransistor CouplerLogic Gate Coupler
Typical useStatus and panel indicationSignal transfer, feedback, low speed isolationDigital isolation, line receiving, fieldbus
Key parameterDominant wavelength and luminous intensityCurrent transfer ratio binData rate and CMR
Value range18 mcd to 180 mcd at 20 mA, 623 nm to 639 nm in the red parts50 percent to 600 percent at 5 mA10 MBd with 5 kV per microsecond to 15 kV per microsecond CMR
IsolationNot applicable5000 V rms, 3750 V rms on small outline parts5000 V rms on the standard 8 pin parts, 3750 V rms on SOIC-8
Output stageNot applicablePhototransistor, 80 V collector to emitterOpen collector or open drain logic output
Package0603, 0805, 1206 and 5 mm through holeDIP-4, SOP-4, DIP-6DIP-8, SOIC-8, wide body DIP-8
Temperature-40 C to +85 C-55 C to +110 C by part-40 C to +85 C
OptionsColour, lens type, intensity binCTR rank, isolation optionEnable pin, surface mount option, tape and reel

Included Models and Order Codes

The table lists the indication and isolation part codes most often requested. Send the complete part number including the bin or rank and the package option and we confirm availability against that string.

Part NumberTypeKey RatingPackageNotes
LTST-C190KRKTRed chip LED, water clear lens18 mcd to 180 mcd at 20 mA, 631 nm dominant, 639 nm peak0603AlInGaP die, bins M to R, forward voltage around 2 V
LTST-C171KYKTYellow chip LEDIntensity binned, water clear lens0805Same construction as the 0603 series in the larger footprint
LTL-307EERed through hole indicatorAround 19 mcd, 623 nm peak, 50 degree viewing angle5 mm T-1 3/4Diffused lens panel indicator, forward voltage around 2.6 V
19-217/S3C-AL2N1VY/3TChip LED, top viewColour and intensity binned0603Surface mount indication part from the 19-217 range
PC817Phototransistor couplerCTR 50 percent to 600 percent at 5 mA, 80 V collector to emitter, 5000 V rmsDIP-4Industry standard part, also available in the SOP-4 footprint
EL817Phototransistor couplerCTR ranked, 5000 V rmsDIP-4Equivalent pinout to the PC817 for the same socket
TLP291Phototransistor couplerCTR 50 percent minimum, GB rank 100 percent minimum, 80 V collector to emitter, 3750 V rmsSOP-4Compact package for high density boards, -55 C to +110 C
TLP291-4Quad phototransistor couplerCTR 50 percent minimum per channel, 2500 V rmsSO16 or SOP-16Four isolated channels in one body, saves board area
6N137Logic gate coupler10 MBd, 5000 V rms, 75 ns propagation delay, open collector outputDIP-8Common mode rejection 10 kV per microsecond typical depending on the source
HCPL-2631Dual logic gate coupler10 MBd per channel, 5 kV per microsecond minimum CMR at VCM 50 VDIP-8 or SOIC-83750 V rms standard, 5000 V rms with the option 020 body
HCPL-2630Dual logic gate coupler1 MBd per channel, TTL compatibleDIP-8 or SOIC-8Slower and lower cost member of the same family
HCPL-2531Dual high speed coupler1 MBd, 1000 V per microsecond CMR, 7 percent CTR minimumDIP-8 or SOIC-8Used for line receiving with high common mode noise
VO2631Dual logic gate coupler10 MBd, 5000 V rms, 5 kV per microsecond CMRDIP-8Open drain output, dual channel option of the 6N137 platform
MOC3021Phototriac coupler, random phase5000 V rms isolation in DIP-6, 400 V blockingDIP-6Drives a triac from a logic signal, random phase switching
MOC3023Phototriac coupler, random phase5000 V rms isolation in DIP-6, low trigger currentDIP-6Sensitive gate version for low drive current

Key Features

Wavelength and intensity stated per part – dominant wavelength, peak wavelength and the intensity bin range are given so the front panel colour matches without sampling

CTR bins identified – couplers are quoted with the current transfer ratio rank, including ranks above 100 percent, because the rank decides the drive current

Speed grade matched to the interface – phototransistor parts for signalling and feedback, 10 MBd logic gate parts for digital isolation and line receiving, quoted separately

Isolation rating confirmed per body – 3750 V rms small outline and 5000 V rms DIP ratings are stated where the same part number exists in both bodies

Common mode immunity quoted – CMR from 5 kV to 15 kV per microsecond for the logic gate couplers, which is the number that matters on a noisy drive stage

Phototriac options for AC loads – zero cross and random phase couplers with 5000 V rms isolation for driving triacs from logic level signals

Applications

The parts are supplied for the boards below. Indication and isolation parts are normally quoted with the SUPERB PCB and SUPERB PCBA work we support for the same board, so the small parts are not a separate purchase.

Status and panel indication – front panel indicators, health LEDs and fault indication with defined colour, brightness and viewing angle

Signal and feedback isolation – phototransistor couplers between a control domain and a power stage, in switching supply feedback and in low speed digital links

Digital isolation and AC switching – 10 MBd couplers on fieldbus, isolated conversion and line receiver interfaces, and phototriacs on AC load switching

Sourcing and Cross-Reference

Optocoupler orders fail on the bin and the rank. The same base part number is supplied in different current transfer ratio ranks, isolation bodies and speed grades, and a board qualified on one rank will not run the same with another. The useful answer is availability by complete order code with the rank stated, not a general stock statement.

We check availability against the full part number including rank and package option and quote the nearest option with the CTR range and isolation difference stated in writing, so the drive current and creepage can be rechecked before the substitution is made.

SUPERB Assembly support covers the SMT build where these boards are assembled in volume.

Q: Can you supply parts from the same current transfer ratio rank as the original order?

A: Yes. Send the complete part number, the rank or bin and the quantity and the SUPERB Tech sales team will confirm availability and the nearest option with the difference stated.

Why Buy From Us

  1. Rank and bin confirmed: current transfer ratio rank, intensity bin and colour are confirmed against the complete order code before quotation
  2. Isolation body stated: where a part exists in both 3750 V rms and 5000 V rms bodies the quoted body is named so creepage requirements are met
  3. Speed grade separated: signalling couplers and 10 MBd logic couplers are quoted as different parts so the interface timing is not changed by accident
  4. Indication and isolation on one line: LEDs, couplers and the protection parts around them can be quoted together so the small BOM items arrive as one delivery

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Discrete and Power Semiconductors, N-Channel and P-Channel Power MOSFETs, Analog and Mixed-Signal ICs, BOM Shortage Recovery.