Real Time Clock ICs and Timing Buffers for Data Logging
Product Specifications
Product Overview
A data logger needs a timestamp that survives a power cut and stays close enough to real time that two units can be compared months later. Two families cover that. A standard I2C real time clock runs from an external 32.768 kHz crystal and holds time in a battery backed register; it costs little and drifts with the crystal, typically 20 ppm, which is about 10 minutes a year. A temperature compensated part integrates the crystal and a correction engine, and holds 2 ppm from 0 C to 40 C and 3.5 ppm over the full industrial range, which is about a minute a year and is what a revenue meter or a medical log needs.
The DS3231SN is the reference for the second group: an I2C part with the crystal and the temperature compensation inside the package, two time of day alarms, a programmable square wave output and a battery input that keeps the oscillator running when the main rail is removed. The DS3232 adds battery backed SRAM for the log buffer so the processor can write through a power fail without an external memory. The standard group, the DS1307, DS1339, PCF8563, M41T81, MCP7940N, BQ32000 and ISL1208, are the parts used where 20 ppm is acceptable and cost is the driver: all are I2C, all take an external 32.768 kHz crystal, and most add alarms and a few bytes of SRAM.
The second half of the page is clock distribution. A logging board often has one reference and several consumers: an ADC that wants a clean master clock, a processor that wants a synchronous input, and a peripheral that needs a divided copy. An LVCMOS buffer takes one input and drives two, four or eight outputs with a fixed skew between them, so all the consumers see the same edge. The CDCLVC1104 and CDCLVC1108 and the LMK1C1104 and LMK1C1108 cover that, with 25 ps of output to output skew, 8 femtoseconds of additive jitter and a 250 MHz maximum at 3.3 V.
Key Specifications
| Parameter | Temperature compensated RTC | Standard I2C RTC | Clock buffers |
|---|---|---|---|
| Accuracy | 2 ppm from 0 C to 40 C, 3.5 ppm from minus 40 C to +85 C | Set by the external crystal, typically 20 ppm | Not applicable, jitter is the relevant number |
| Interface | I2C at 400 kHz | I2C at 100 kHz or 400 kHz | Single ended LVCMOS in and out |
| Timekeeping | Seconds to year with leap year correction to 2100 | Seconds to year, some parts with century bit | Not applicable |
| Alarms | Two time of day alarms and a square wave output | One or two alarms, some parts with a periodic output | Not applicable |
| Backup | Battery or supercapacitor input, automatic switchover | Battery input on most parts | Not applicable |
| Memory | 236 bytes of battery backed SRAM on the DS3232 | 56 bytes on the DS1307, none on the PCF8563 | Not applicable |
| Outputs | Not applicable | Not applicable | 2, 4 and 8 outputs, 25 ps output to output skew |
| Supply | 2.3 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V, 2.5 V and 3.3 V |
| Package | SOIC-16 and SOIC-20 | SO-8 and SOIC-8 | TSSOP-8, TSSOP-16 and WSON |
Included Models and Order Codes
The table lists the real time clocks and buffers most often quoted for logging and metering boards. State the accuracy the application needs, the backup source, the bus and the number of clock outputs, and the order code is confirmed with packing.
| Part Number | Function | Accuracy | Interface | Backup | Package |
|---|---|---|---|---|---|
| DS3231SN#T&R | Temperature compensated RTC with integrated crystal | 2 ppm from 0 C to 40 C | I2C | Battery input | SOIC-16 |
| DS3232SN#T&R | Temperature compensated RTC with 236 bytes SRAM | 2 ppm from 0 C to 40 C | I2C | Battery input | SOIC-20 |
| DS1307ZN+ | Standard RTC with 56 bytes SRAM | Crystal dependent | I2C | Battery input | SOIC-8 |
| DS1339U-33+T&R | Standard RTC with two alarms | Crystal dependent | I2C | Battery input | uSOP-8 |
| PCF8563T/5,518 | Standard RTC with alarm and timer | Crystal dependent | I2C | Battery input | SO-8 |
| M41T81SM6F | Standard RTC with alarm and watchdog | Crystal dependent | I2C | Battery input | SO-8 |
| MCP7940N-I/SN | Standard RTC with SRAM and unique ID | Crystal dependent | I2C | Battery input | SOIC-8 |
| BQ32000DR | Standard RTC with automatic backup switchover | Crystal dependent | I2C | Supercapacitor or battery | SOIC-8 |
| ISL1208IB8Z | Standard RTC with alarm and event detection | Crystal dependent | I2C | Battery input | SOIC-8 |
| RV-3028-C7 | Temperature compensated RTC in a small package | Crystal dependent trim, low power | I2C | Battery input | Chip scale |
| CDCLVC1104PW | Four output LVCMOS clock buffer | 25 ps output skew | LVCMOS | Not applicable | TSSOP-8 |
| CDCLVC1108PW | Eight output LVCMOS clock buffer | 25 ps output skew | LVCMOS | Not applicable | TSSOP-16 |
| LMK1C1104PWR | Four output LVCMOS buffer, 250 MHz at 3.3 V | 8 fs additive jitter | LVCMOS | Not applicable | TSSOP-8 |
| LMK1C1108PWR | Eight output LVCMOS buffer, 250 MHz at 3.3 V | 8 fs additive jitter | LVCMOS | Not applicable | TSSOP-16 |
Key Features
Timestamp that survives a power cut – the battery input keeps the oscillator and the register running, so the log resumes with the right time rather than with the time of the last power up.
Accuracy stated over temperature – 2 ppm from 0 C to 40 C and 3.5 ppm over the industrial range is a drift figure for the whole part, not a crystal specification that ignores the load capacitance.
Alarms and square wave output – a periodic interrupt can wake a sleeping processor for a measurement instead of a timer that drifts with temperature.
Battery backed SRAM – the DS3232 holds 236 bytes through a power fail, which is enough for the last records before a supply drop without an external memory.
Clock distribution with fixed skew – 25 ps output to output skew means the ADC and the processor see the same edge, which keeps the sampling instant stable.
Small packages – SO-8 and chip scale bodies fit behind a connector or under a shield can, where a 16 pin SOIC will not go.
Applications
These parts are quoted for logging, metering and clock distribution, typically where: A logging board is normally quoted with the SUPERB PCB and SUPERB PCBA work we support for the same product, so the clock, its crystal and the assembly arrive as one order.
Utility meters and data loggers – a timestamp that has to agree between units after months in the field, with a battery or supercapacitor that carries the clock through outages.
Medical and laboratory instruments – an event log that is read against a real clock during an audit, where a minute a year of drift is the difference between a pass and a finding.
Boards with several clock consumers – one reference distributed to an ADC, a processor and a peripheral through a buffer, with the skew fixed by the part rather than by trace length.
Sourcing and Cross-Reference
Real time clocks are specified by three fields that the family name does not show: the accuracy class, the backup arrangement and the package. The DS3231SN and the DS3231MZ share a function and differ in package and in the trim arrangement; the PCF8563 and the DS1307 are both I2C clocks in an SO-8 body and are not pin compatible. We quote the full order code and state the accuracy class and the package on the confirmation, so a replacement is a decision rather than a surprise.
The crystal is the other half of the accuracy on the standard parts. A 20 ppm clock is only 20 ppm if the load capacitance matches the crystal, and the two are usually bought on separate lines of the BOM. Where both are on the same board we quote them together and state the load capacitance the clock expects, which is the cheapest way to avoid a batch of units that drift by different amounts.
Where the boards are assembled in volume, SUPERB Assembly support covers the SMT build of the timing and logging sections.
Q: Can you supply the real time clock and its 32.768 kHz crystal as a matched pair?
A: Yes. Send the complete order code, the accuracy class and the backup source, and the SUPERB Tech sales team will confirm availability and the crystal that matches the load capacitance.
Why Buyers Source Timing Parts Through SUPERB
- Accuracy class on the quote: the difference between 2 ppm and 20 ppm is a different part, a different price and a different calibration interval, and it is stated per line.
- Clock and crystal together: the load capacitance the clock expects and the crystal that matches it are quoted as one set, which removes the most common cause of drift between batches.
- Backup arrangement checked: battery, supercapacitor and switchover behaviour are confirmed against the board, not assumed from the family.
- Buffers for the same board: the clock, the buffer and the crystal for one board come from one quotation, so the skew and the load are calculated with the parts that will be fitted.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Crystals and oscillators, Crystal units and TCXO oscillators, Clock generators, eMMC and NAND storage, Obsolete part cross reference.