Contact Us
  • Home
  • COMPONENTS
  • Barometric Pressure and Altitude Sensors for Drones and Navigation

Barometric Pressure and Altitude Sensors for Drones and Navigation

Absolute pressure sensors from 10 mbar to 1260 hPa coverage Altitude resolution from about 1 m down to 10 cm for variometers I2C and SPI interfaces in LGA packages for flight controller boards All models on this page are grouped into one part for easy sourcing
quote now

Product Specifications

Product Overview

Altitude from pressure is simple arithmetic with a hard requirement behind it: the sensor has to resolve a pressure change small enough to see height. One metre of altitude near sea level is about 12 Pa, and 10 cm is about 1.2 Pa, which is why the resolution and noise figures on the first page of a datasheet decide whether a part is good enough for a variometer or only for a weather reading.

On a flight controller the pressure sensor also has to survive a hostile board: propeller wash, motor vibration, temperature steps from the power stage and the airflow through the enclosure all reach the sensing element. The parts on this page are used because their relative accuracy is specified over a pressure window and a temperature range, and because the compensation coefficients are stored on chip, so the host does not have to run a calibration of its own.

All models are grouped into this single product, so one enquiry can cover the sensor, its decoupling, the gel or the cover over the port and the second source for the same footprint. Tell us the required altitude resolution, the update rate, the supply rail and the port arrangement, and the class can be matched to the board rather than the other way round.

Key Specifications

ParameterHigh Resolution TypesStandard Types
Pressure range10 mbar to 1200 mbar or 300 hPa to 1200 hPa260 hPa to 1260 hPa, or 300 hPa to 1100 hPa
Relative accuracy0.06 hPa to 0.12 hPa (about 0.5 m to 1 m)0.1 hPa over 800 hPa to 1100 hPa
Altitude resolution10 cm for variometer grade partsAbout 1 m for floor and altitude indication
InterfaceI2C and SPI, up to 128 Hz conversion rateI2C and SPI, 1 Hz to 75 Hz data rate
Supply voltage1.7 V to 3.6 V1.7 V to 3.6 V, 2.7 V to 3.6 V for the eMMC era parts
Package8 pin and 10 pin LGA, 2.0 x 2.0 mm to 2.5 x 2.5 mm, 0.6 mm to 1.0 mm highLGA with a metal lid, plus encapsulated versions rated for water and dust
Temperature range-40 C to 85 C operating, 0 C to 65 C for full accuracy-40 C to 85 C operating
Data output16 bit and 24 bit pressure plus 16 bit temperature16 bit and 24 bit, compensation on chip

Included Models and Order Codes

The table lists the pressure and altitude sensors most often specified for flight controllers, altimeters and navigation boards. Send the exact order code and the quantity and we confirm availability, date code and the nearest second source in the same footprint.

ModelPressure RangeAccuracy / ResolutionInterfacePackage
BMP280300 hPa to 1100 hPaRelative accuracy 0.12 hPa, equal to 1 m at 700 hPa to 900 hPaI2C up to 3.4 MHz, SPI up to 10 MHz8 pin LGA, 2.0 x 2.5 x 0.95 mm, metal lid
BME280300 hPa to 1100 hPaSame pressure core as BMP280 plus relative humidity outputI2C and SPI8 pin LGA
BMP180300 hPa to 1100 hPaRMS noise 3 Pa, pressure resolution 1 PaI2C8 pin LGA, 3.6 x 3.8 mm
BMP388300 hPa to 1250 hPaLow noise 24 bit output for altitude holdI2C and SPI10 pin LGA, 2.0 x 2.0 x 0.75 mm
BMP390300 hPa to 1250 hPaSuccessor to BMP388 with lower noiseI2C and SPI10 pin LGA, 2.0 x 2.0 x 0.75 mm
BMP581300 hPa to 1100 hPaLow power 24 bit output for fitness and navigationI2C and SPI10 pin LGA, 2.0 x 2.0 x 0.95 mm
DPS310300 hPa to 1200 hPaRelative accuracy 0.06 hPa (0.5 m), absolute accuracy 1 hPa, precision 0.002 hPaI2C and SPI up to 128 Hz8 pin LGA, 2.5 x 2.5 mm, 1.7 V to 3.6 V
DPS368300 hPa to 1200 hPaSame sensing core as DPS310 with encapsulated packageI2C and SPIEncapsulated 8 pin package rated for water and dust
LPS22HB260 hPa to 1260 hPaRelative accuracy 0.1 hPa over 800 hPa to 1100 hPa, 24 bit output, 22,000 g shock ratedI2C and SPI, 1 Hz to 75 HzMEMS nano package, 1.7 V to 3.6 V
LPS22HH260 hPa to 1260 hPaHigh performance version with 24 bit output and FIFOI2C and SPISame footprint as LPS22HB
LPS25HB260 hPa to 1260 hPa24 bit pressure output, 16 bit temperature outputI2C and SPIMEMS nano package
MS5611-01BA0310 mbar to 1200 mbarPressure resolution 0.012 mbar, altitude resolution 10 cm, 24 bit ADC, stainless steel capI2C and SPI up to 20 MHzQFN with metal cap, -40 C to 85 C
MS5607-02BA0310 mbar to 1200 mbarLower resolution variant of the MS5611 family, 24 bit ADCI2C and SPIQFN with metal cap
SPL06-001300 hPa to 1100 hPaLow power digital output for drone altitude holdI2C and SPISmall LGA package
ICP-1010030 kPa to 110 kPaLow noise differential pressure and altitude measurementI2C and SPISurface mount package for wearable and drone boards

Key Features

Resolution Stated In Metres – The parts are chosen on the pressure resolution that converts to the altitude step the application needs, from about 1 m for floor detection to 10 cm for a variometer.

Relative Accuracy Over A Window – Relative accuracy over a defined pressure band is the figure that governs altitude hold, and it is quoted over a temperature range rather than at a single point.

Compensation On Chip – Calibration coefficients are stored in the device, so the host firmware reads a compensated value instead of running its own polynomial compensation.

Interfaces Matched To The Controller – I2C and SPI versions in the same family, so a board can keep the same footprint when the interface changes between revisions.

Low Power For Battery Boards – Microamp class average current at 1 Hz sampling keeps the sensor inside the power budget of a handheld or a battery powered node.

Encapsulated And Ported Options – Open port for a tube to the outside, or an encapsulated package for boards that are washed or exposed, chosen with the enclosure in mind.

Second Sources For The Same Footprint – Where a part is obsolete or on allocation, the nearest pin and footprint compatible device in the family is quoted with the accuracy difference stated.

Applications

Applications where these sensors are used: Because the pressure sensor sits on the same board as the inertial parts, it is normally quoted with the SUPERB PCB and SUPERB PCBA work we support rather than on its own.

Flight Controllers And Altitude Hold – Multirotor and fixed wing boards that need a stable pressure reading at high update rate to hold altitude and to feed the height estimate.

Barometric Altimeters And Variometers – Paragliding, skydiving and hiking instruments where 10 cm resolution and low drift decide whether the climb rate is usable.

Weather And Instrumentation Nodes – Environmental and industrial recorders that log absolute pressure and temperature over long periods at low power.

Indoor Navigation And Wearables – Floor detection in buildings, step counting and activity tracking where the pressure change between floors has to be resolved with little current.

Sourcing and Cross-Reference

Pressure sensors move through lifecycle quickly: several parts on this page are already marked as not recommended for new designs by their vendor while the boards that use them stay in production, and the replacement usually changes the package height or the port arrangement. That is the point at which a drop in substitute has to be identified rather than assumed.

We compare the candidates on the figures that actually matter for altitude work: relative accuracy over the realistic pressure window, noise, conversion time and the compensation scheme. Where the substitute needs firmware changes because the coefficients or the register map differ, that is stated with the quote so the software can be planned in parallel with the parts.

SUPERB Assembly support covers the SMT build where the sensor boards are assembled in volume.

Q: Can you supply a drop in replacement for an obsolete barometric pressure sensor?

A: Yes. Send the order code and the quantity and the SUPERB Tech sales team will confirm availability and the nearest part in the same footprint.

Why Source Pressure Sensors from Superb Automation?

  1. Specialised Sourcing Focus: Sensors, RF parts and mixed signal devices for industrial, telecom, medical and defence builds, matched on the datasheet figures that matter to the application.
  2. Hard To Find And Obsolete Parts: Pressure sensors that go out of production while boards stay in service, sourced with the vendor status and the nearest equivalent stated up front.
  3. Cross Reference Support: Package height, port arrangement, register map and compensation scheme differences listed with the quote so the substitute can be signed off before production.
  4. Stock And Build Quantities: Prototype quantities for the first boards, repair quantities and volume orders are all welcome, with batch information stated per line.
  5. BOM Kitting: The pressure sensor, the inertial sensors and the interface parts for the same board can be quoted together.
  6. Reply With Evidence: Documents, batch marking and the condition of the parts are stated on the quote before the order is placed.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: BOM Shortage Recovery, Sensors and Detectors, 6-Axis IMU Sensors for Flight Control and Navigation, Obsolete RF Part Replacement.