USB Type-C and Power Delivery Controllers for Portable Devices
Product Specifications
Product Overview
A USB Type-C port is two functions on one connector: a channel that senses what is plugged in, and a power path that has to carry the current the two ends agree on. The controller does the first part, and the difference between the parts on this page is mostly how much of the second part sits inside the package. A barrel connector replacement needs a sink controller, five resistors and a connector, while a docking station with two ports and DisplayPort alt mode needs a part with two managed power paths, thirteen GPIOs and firmware hooks for the mux.
The sink group starts with the STUSB4500, which negotiates a contract up to 20 V at 5 A without any MCU. Three power data objects are held in non volatile memory, the device runs from a dead battery and protects the CC pins against a short to VBUS up to 22 V, with the VBUS pins rated to 28 V. The CYPD3177 does the same job for a barrel connector replacement with an integrated 24.5 V LDO, a VBUS gate driver with soft start, an oscillator and IEC 61000-4-2 level 4C ESD on the CC and VBUS pins, so a device that used to take a 19 V brick can take a Type-C cable with no firmware at all.
The dual role and source parts move the power path on chip. The TPS65987D and the TPS65988 carry two 5 V to 20 V, 5 A, 25 milliohm bidirectional switches, with undervoltage, overvoltage and inrush current limiting on each path, and they speak USB PD 3.0, BC1.2 and DisplayPort alt mode over I2C or GPIO. The STUSB4700 is the hardware only source side: five PDOs in NVM, a configurable start up profile, 22 V protection on CC and 28 V on VBUS, no software. At the small end, the FUSB302B is the physical layer only, a Type-C transceiver with a 48 byte transmit and 80 byte receive FIFO that lets the host run the policy, in a 1.2 by 1.3 mm WLCSP or a 2.5 mm square MLP.
Key Specifications
| Parameter | Sink controllers | Source and dual role controllers |
|---|---|---|
| Role | UFP sink, up to 100 W | DFP source or DRP, one or two ports |
| Contract | Up to 20 V at 5 A | Up to 20 V at 5 A per port |
| Power path | External P or N channel FET through a gate driver | Two integrated 25 milliohm switches, or external FETs |
| Supply range | 3.0 V to 24.5 V on VBUS_IN, 2.7 V to 5.5 V on VDDD | 3.3 V rail or VBUS, 3.3 V LDO for dead battery |
| Host interface | I2C at up to 1 MHz, alert pin | I2C, SPI and up to 13 GPIOs |
| Configuration | 3 PDOs in NVM, no firmware | Register and patch bundle loaded over I2C |
| Protection | VBUS to CC short, OVP, inrush limit | UVLO, OVP, reverse current, inrush limit, thermal |
| Package | QFN-24 4 by 4 mm, WLCSP-25 | QFN-56 7 by 7 mm, MLP-14 2.5 mm |
Included Models and Order Codes
The table lists the order codes most often quoted for chargers, docks, instruments and handheld devices. State the role, the maximum contract, whether the power FET is on the die, the number of ports and the host interface, and the part and its packing are confirmed.
| Part Number | Role | Contract | Power Path | Interface | Package |
|---|---|---|---|---|---|
| TPS65987D | Single port, DRP, PD 3.0 | 20 V at 5 A | Two integrated 25 milliohm bidirectional switches | I2C, 13 GPIO, DP alt mode | QFN-56, 7 by 7 mm |
| TPS65988 | Dual port, DRP, PD 3.0 | 20 V at 5 A per port | Two managed paths per port, 25 milliohm each | I2C, GPIO, BC1.2 | QFN-56, 7 by 7 mm |
| STUSB4500QTR | Sink, PD 3.0, auto run | 20 V at 5 A, 100 W | External FET, VBUS_EN_SNK gate driver | I2C optional, 3 PDOs in NVM | QFN-24 EP, 4 by 4 mm |
| STUSB4500BJR | Sink, PD 3.0, auto run | 20 V at 5 A, 100 W | External FET, dead battery mode | I2C optional, 3 PDOs in NVM | WLCSP-25, 2.6 mm |
| STUSB4700QTR | Source, DFP, PD 2.0 | Up to 20 V, 5 PDOs | External FET, VBUS_EN_SRC driver | I2C and interrupt, no software | QFN-24 EP, 4 by 4 mm |
| CYPD3177-24LQXQ | Sink, PD 3.0, BCR | Up to 100 W, 20 V at 5 A | External PFET with soft start gate driver | I2C slave at 0x08, up to 1 Mbps | QFN-24, 4 by 4 mm |
| FUSB302BMPX | DRP, PD 2.0 v1.2 | Up to 100 W | None, Type-C transceiver and VCONN switch | I2C at up to 1 MHz | MLP-14, 2.5 by 2.5 mm |
| FUSB302BUCX | DRP, PD 2.0 v1.2 | Up to 100 W | None, VCONN switch with current limit | I2C at up to 1 MHz | WLCSP-9, 1.215 by 1.26 mm |
| FUSB302BVMPX | DRP, AEC-Q100 grade 2 | Up to 100 W | None, VCONN switch with current limit | I2C at up to 1 MHz | MLP-14, -40 to 105 C |
Key Features
Contract handled without firmware – the sink parts keep three power data objects in non volatile memory, so a product with no spare flash still asks for 15 V or 20 V instead of falling back to 5 V.
Power path on the die – two 25 milliohm bidirectional switches remove the external FET pair, the charge pump and the current sense that a discrete path needs.
CC short protection – the CC pins sit next to VBUS in the connector, and a 22 V rating is what stops a bent pin from destroying the controller.
Dead battery operation – a flat battery still has to be recognisable, so the sink parts present Rd on both CC pins before any rail is up.
Alt mode control – GPIO or I2C lines drive the SuperSpeed mux, which is what makes a single connector carry DisplayPort as well as power.
Small packages – a 1.2 by 1.3 mm WLCSP or a 2.5 mm MLP keeps the controller inside a handheld enclosure where the connector is the tallest part.
Applications
These controllers are quoted for products that charge or are charged over a Type-C cable, typically where: A Type-C board is normally quoted with the SUPERB PCB and SUPERB PCBA work we support for the same assembly, so the connector, the protection array and the controller arrive together.
Handheld instruments and test gear – a 15 V or 20 V contract replaces a proprietary brick, and a sink controller with NVM keeps the negotiation identical across a product family.
Docks, monitors and hubs – two ports, DisplayPort alt mode and a 5 A path per port call for the dual port part with managed switches and thirteen GPIOs.
Portable chargers and power banks – a source controller with five PDOs lets one board advertise 5 V to 20 V, and an external FET keeps the heat away from the controller.
Sourcing and Cross-Reference
Type-C parts are lost on policy, not on pins. Two controllers with the same footprint can differ in whether they answer a Discover Identity request, in the number of PDOs they hold, and in whether they keep the contract when the host reboots. We quote the PD revision, the role, the PDO count and the power path resistance on the confirmation, so a drop in replacement can be checked against the charger it will meet rather than against the footprint alone.
The second half of the BOM matters as much as the controller: the CC and VBUS ESD array, the VBUS capacitor that has to hold the contract through a cable bounce, and the FET or fuse that carries 5 A. We quote the controller, the protection array and the pass devices for one port as a set, so the thermal and inrush numbers are calculated on parts that will actually be fitted.
Where the port boards are built in volume, SUPERB Assembly support covers the SMT build and the inspection of the fine pitch QFN and WLCSP parts.
Q: Can you supply a Type-C PD controller that replaces an existing barrel jack with no firmware change?
A: Yes. Send the current connector, the voltage and current the product needs and whether a host processor is present, and the SUPERB Tech sales team will confirm the order code, the packing and the nearest part that keeps the same control interface.
Why Buyers Source Type-C Parts Through SUPERB
- Role and contract on the quote: the PD revision, the role, the PDO count and the switch resistance are stated per line, so the part matches the charger and the cable it will see.
- Controller and protection together: the ESD array, the VBUS capacitor and the pass device for one port are quoted as a set, so the inrush and thermal figures are not estimates.
- Fine pitch assembly: WLCSP and 0.4 mm pitch QFN parts are placed and inspected on the same line that supplies them, which keeps first pass yield visible.
- Long lifecycle supply: parts that a charger was qualified around are held with date codes, so a product stays in production while an alternative is qualified.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Multi-function ICs, Battery chargers and fuel gauges, Load switches and hot swap controllers, Digital isolators, Pin to pin cross reference.