Contact Us
  • Home
  • COMPONENTS
  • CAN Bus Transceivers and Controllers for Automotive and Industrial Networks

CAN Bus Transceivers and Controllers for Automotive and Industrial Networks

CAN bus transceivers and stand-alone CAN controllers for automotive and industrial networks Isolated 2500 V and 5000 V parts, 3.3 V and 5 V transceivers, SPI CAN controllers All models listed below are combined into this single product for easy sourcing Samples, build quantities, alternatives and cross reference are supported
quote now

Product Specifications

Product Overview

A CAN node is two parts: a controller that formats the frames, and a transceiver that drives the differential bus. Plenty of microcontrollers include the controller, so only the transceiver is needed, but boards with a processor that has no CAN peripheral use a stand-alone controller such as the MCP2515 over SPI. Both cases are covered on this page.

The parts below span the three situations that come up most often: 5 V transceivers such as the MCP2551 and SN65HVD251 for equipment designed years ago, 3.3 V transceivers such as the SN65HVD230 that connect directly to a modern microcontroller, and galvanically isolated transceivers such as the ISO1050 for motor drives, battery systems and multi ground installations where a ground loop would otherwise destroy the interface.

All models are grouped into this single product, so a CAN node enquiry can cover the controller, the transceiver, the termination resistors and the isolated DC-DC supply for the bus side in one reply.

Electrical Specifications

ParameterIsolated CAN transceiver3.3 V CAN transceiver5 V CAN transceiver
StandardISO 11898-2ISO 11898-2ISO 11898-2
Signalling rateup to 1 Mbit/sup to 1 Mbit/sup to 1 Mbit/s (MCP2551 up to 1 Mbit/s)
Isolation2500 V RMS (DUB package), 5000 V RMS (DW package), transient immunity 50 kV/us typicalnonenone
Loop delay150 ns typical, 210 ns maximumnot specified as isolation path delaynot specified as isolation path delay
Bus fault protection-27 V to +40 V on the bus pins-4 V to +16 V typical, +/-16 kV HBM ESD on bus pinswide transient and short circuit range
Common mode range-12 V to +12 V-7 V to +12 V typical-7 V to +12 V typical
Supply3.3 V on side 1, 5 V on side 2 (also available as 5 V / 5 V)single 3 V to 3.6 V supply4.5 V to 5.5 V
Low power modesdriver dominant time outstandby mode at 370 uA typical (HVD230), sleep at 40 nA typical (HVD231)slope control pin to reduce emissions

Included Models and Order Codes

Order codes below include the package and the temperature code. The isolated parts are also listed with the isolation rating, because the DUB and DW packages do not have the same one.

ModelTypeRateSupplyPackageNotes
ISO1050DUBRIsolated CAN transceiver1 Mbit/s3.3 V / 5 VSOP-8 (DUB)2500 V RMS isolation, fail safe outputs, 150 ns typical loop delay
ISO1050DWRIsolated CAN transceiver1 Mbit/s3.3 V / 5 VSOIC-16 wide (DW)5000 V RMS isolation version; ISO1042 is the current recommendation for new designs
SN65HVD230DR3.3 V CAN transceiver1 Mbit/s3 V to 3.6 VSOIC-8Low current standby mode at 370 uA typical, up to 120 nodes on a bus
SN65HVD231DR3.3 V CAN transceiver1 Mbit/s3 V to 3.6 VSOIC-8Ultra low current sleep mode at 40 nA typical
SN65HVD232DR3.3 V CAN transceiver1 Mbit/s3 V to 3.6 VSOIC-8Version without the standby pin for fixed active operation
SN65HVD233DR3.3 V CAN transceiver1 Mbit/s3 V to 3.6 VSOIC-8Loopback and diagnostic modes
SN65HVD234DR3.3 V CAN transceiver1 Mbit/s3 V to 3.6 VSOIC-8Enable and standby control for bus managed designs
SN65HVD251DR5 V CAN transceiver1 Mbit/s4.5 V to 5.5 VSOIC-85 V part for equipment designed around the earlier standard
SN65HVD1050DR5 V CAN transceiver1 Mbit/s4.5 V to 5.5 VSOIC-8Alternate 5 V part with the standard pin out
MCP2551T-I/SN5 V CAN transceiver1 Mbit/s4.5 V to 5.5 VSOIC-8Industry standard pin out, slope control pin for lower RFI, -40 C to +125 C
TJA1050T5 V CAN transceiver1 Mbit/s4.75 V to 5.25 VSO-8Widely used automotive part, pin compatible with the MCP2551 footprint
TJA1042TK/3,15 V CAN transceiver1 Mbit/s4.5 V to 5.5 VHVSON-8 (TK)Standby mode version for permanent bus nodes
MCP2515T-I/STStand-alone CAN controller1 Mbit/s2.7 V to 5.5 VTSSOP-18SPI interface to any MCU, CAN 2.0B active, -40 C to +125 C
MCP2515T-I/SOStand-alone CAN controller1 Mbit/s2.7 V to 5.5 VSOIC-18Same controller in the wide body SOIC package

Key Features

Isolated And Non Isolated Options – Parts with 2500 V and 5000 V RMS barriers for drives and battery systems, and standard parts for equipment that shares a ground with the network.

3.3 V And 5 V Interfaces – Direct connection to modern microcontrollers at 3.3 V, and 5 V parts for boards that cannot be changed.

Low Power Modes – Standby at hundreds of microamps and sleep at tens of nanoamps, which matters for nodes that stay powered on a vehicle or a battery bank.

Bus Protection – Bus fault protection, cross wire protection, loss of ground protection, thermal shutdown and ESD ratings stated per part.

Stand-Alone Controller Option – The MCP2515 adds CAN 2.0B to any microcontroller over SPI, without changing the host processor.

Diagnostic Modes – Loopback and silent mode support for bring up and fault finding, on the parts that provide it.

Automotive Temperature Grades – Parts specified to +125 C where the node sits next to a motor, a charger or an engine bay.

Applications

Networks and boards that use these parts: A CAN node is normally quoted with the SUPERB PCB and SUPERB PCBA work we support, so the transceiver, the controller, the termination parts and the assembly come from one source.

Automotive And Telematics Modules – Gateway, body control and telematics units that have to keep the same interface parts through a long vehicle programme.

Motor Drives And Battery Systems – Isolated transceivers between a control board and a power stage, where a ground potential difference would otherwise damage the interface.

Industrial Automation And PLC Networks – Machine networks where several nodes share a bus over long cable runs and the network has to survive wiring faults.

Charging And Energy Storage Equipment – Battery management and charging racks with CAN links between modules and the system controller.

Sourcing and Cross-Reference

CAN parts are commonly specified by pin out rather than by part number, and several vendors share the same footprint. That makes substitution practical, but only if the electrical differences are known: the common mode range, the bus fault voltage, the low power mode pins and the loop delay all differ, and on an isolated part the package decides the isolation rating (the same ISO1050 family is 2500 V RMS in the DUB package and 5000 V RMS in the DW package).

Where a part has been superseded, we say so. The ISO1050 is a good example: it is still sourced and still used, but the vendor recommends the ISO1042 for all new isolated CAN designs, so we state that in the quote rather than letting a new design move onto a mature part without knowing it. Related interface parts for the same boards, such as the SN65HVD3082E and SN65HVD75 RS-485 transceivers, are also sourced on request.

For volume builds, SUPERB Assembly support covers the SMT assembly of the interface board.

Q: Can you supply a pin-compatible CAN transceiver alternative when the original part is discontinued?

A: Yes. Send the part number and the quantity and the SUPERB Tech sales team will confirm availability and a pin compatible alternative where one exists.

Why Source CAN Interface Parts from Superb Automation?

  1. Interface Part Focus: CAN and RS-485 transceivers and controllers supplied as a group, with the pin out and the protection ratings of each part compared.
  2. Isolation Rating Accuracy: The isolation voltage is quoted per package, because that is how the part is actually specified.
  3. Superseded Part Guidance: Where a vendor recommends a newer device for new designs, the quote says so, and both parts are offered.
  4. Automotive Grades: High temperature parts for nodes next to motors, chargers and other heat sources.
  5. Network Level Kitting: Transceivers, controllers, termination resistors, common mode chokes and isolated supply parts for the same bus quoted together.
  6. Reply With Condition Stated: Marking, packing and condition on the quote, which matters for interface parts that are often pulled from scrap boards.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Multi-Function ICs, MCU and Embedded Processors, Components, Component Sourcing and Supply.