Contact Us
  • Home
  • COMPONENTS
  • Power over Ethernet PD Controllers for Powered Devices

Power over Ethernet PD Controllers for Powered Devices

PD interface controllers for IEEE 802.3af, 802.3at and 802.3bt powered devices. PD power from 13 W on type 1 up to 71.3 W on class 8, with 5 event classification. Integrated hotswap FETs from 0.3 ohm, or external FETs for the highest efficiency. Flyback, forward and buck converter controllers on the same die as the interface.
quote now

Product Specifications

Product Overview

Power over Ethernet puts 48 V on the same four pairs that carry the data, and the device at the far end has to earn that power before it is allowed to draw it. The sequence is fixed by the standard. The powered device first presents a 25 kohm signature so the switch can tell a PD from a laptop port, then a classification current so the switch knows which power class to allocate, then it charges its input capacitance through a hotswap FET with a controlled inrush, and only then does the DC-DC converter start. A PD controller is the part that sequences those steps, and the converter controller is increasingly on the same die.

The integrated group covers the common cases. The TPS23753A is an 802.3at type 1 interface with a 100 V, 0.7 ohm hotswap FET, a 405 mA current limit and a 140 mA inrush, combined with a current mode controller for an isolated flyback at up to 78 percent duty cycle, in a 14 pin TSSOP, and it supports adapter ORing so a 12 V wall supply can take priority. The TPS23730 moves to 802.3bt type 3 with a 0.3 ohm FET, power up to 60 W, primary side regulation on a flyback or an active clamp forward, automatic maintain power signature, and spread spectrum dithering for the EMI filter. The LTC4267 is the 802.3af classic: a 100 V, 400 mA switch, dual level inrush, programmable class 0 to 4 and a 300 kHz current mode regulator in a 16 pin SSOP or DFN. The Si3404 puts the interface, the hotswap FET and the switching FET in a 4 by 4 mm QFN with a 120 V absolute maximum, which is the smallest full type 1 solution on the page.

Above about 30 W the pass device has to leave the package. The LT4295 is an 802.3af, at and bt controller with 5 event classification, an external N channel hotswap FET, a 100 V absolute maximum and a controller that can run either a no-opto flyback or a forward converter, with auxiliary power sensed down to 9 V. The NCP1095 is the interface only, supporting up to 90 W through an external FET with 5 event classification, autoclass, a 110 mA inrush limit and a power good output that enables the main converter. Both are the shape used on outdoor cameras, access points and industrial switches, where the heat of a 0.3 ohm FET at 60 W is no longer acceptable.

Key Specifications

ParameterIntegrated FET controllersExternal FET controllers
Standard802.3af and 802.3at type 1, 802.3bt type 3802.3af, 802.3at and 802.3bt to class 8
PD power13 W to 60 WUp to 71.3 W, and 90 W with the NCP1095
Hotswap switch0.3 ohm to 0.7 ohm on the die, 100 V ratingExternal N channel FET chosen by the user
Inrush limit140 mA on the TPS23753A, set by the FET on the othersSet by the sense resistor, 110 mA typical on the NCP1095
ClassificationSingle event, or 5 event on the bt parts5 event physical layer classification
ConverterCurrent mode flyback, forward or buck on the same dieController only, converter built around it
Switching frequency220 kHz to 300 kHz, 250 kHz typical on the TPS23730Set by the external components
Auxiliary supplyAdapter ORing on most partsAUX sense down to 9 V on the LT4295

Included Models and Order Codes

The table lists the PD controller order codes most often quoted for cameras, access points and industrial gateways. State the standard and class, the PD power, the inrush limit and whether the pass FET is integrated, and the order code is confirmed with packing.

Part NumberStandardPD PowerHotswap SwitchDC-DC ControllerNotes
TPS23753A802.3at type 113 W100 V, 0.7 ohm integrated, 405 mA limitCurrent mode isolated flyback14 pin TSSOP, adapter ORing, 140 mA inrush
TPS23730802.3bt type 3, class 1 to 6Up to 51 W at the PD input, 60 W operation100 V, 0.3 ohm integratedFlyback with primary side regulation, or active clamp forwardAutomatic MPS, spread spectrum dithering
LTC4267802.3af12.95 W100 V, 400 mA integratedCurrent mode flyback, 300 kHzDual level inrush, class 0 to 4, 16 pin SSOP or DFN
LT4295802.3af, at and bt71.3 W, class 8External N channel FETNo-opto flyback or forward5 event classification, 100 V absolute maximum, 28 pin QFN
NCP1095802.3af, at and btUp to 90 WExternal N channel FETNone, interface only5 event, autoclass, 110 mA inrush, 16 pin TSSOP
Si3404802.3at type 112.95 WIntegrated hotswap and switching FETFlyback or buck, 220 kHz typical120 V absolute maximum, 20 pin 4 by 4 mm QFN
MAX5941A802.3af12.95 WIntegrated isolation FETCurrent mode flyback or forward, 275 kHzEnd of life, still supplied from stock

Key Features

Detection and classification in hardware – the signature resistor and the class current are set by resistors, so the PD is recognised by any compliant switch without firmware.

Inrush control – the hotswap FET is turned on slowly and the current is limited, so a large input capacitor does not pull the port down and trip the switch.

Integrated or external FET – a 0.3 ohm FET on the die suits a 25 W camera, while an external FET is what keeps a 60 W access point cool.

Adapter priority – an auxiliary input can be given priority over PoE, which is how a device keeps running when the switch reboots.

Maintain power signature – the bt parts pulse a minimum current automatically, so a device in standby is not disconnected as an idle port.

Converter on the same die – the flyback or forward controller shares the die with the interface, which removes the sequencing problem between two separate parts.

Applications

These controllers are quoted for equipment that is powered from the network cable, typically where: A PD board is normally quoted with the SUPERB PCB and SUPERB PCBA work we support for the same product, so the controller, the transformer and the assembly come from one source.

IP cameras and wireless access points – a 13 W to 25 W device needs a compact type 1 or type 2 interface and a flyback that fits behind the connector, with adapter ORing for a local supply.

Industrial switches and gateways – a DIN rail device with several ports needs a PD interface that survives the surge on a long cable and a converter that holds regulation across the full 36 V to 57 V range.

Displays and signage – a large panel or an information display at 60 W needs a bt interface with an external FET and a converter that keeps efficiency above 90 percent end to end.

Sourcing and Cross-Reference

PoE parts fail on the details of the standard rather than on the silicon. A type 1 controller cannot answer a 5 event classification, and a part that ignores the second class event will be allocated 13 W on a switch that could have given it 25 W. A type 3 part with a 0.7 ohm FET will work at 25 W and will shut down on thermal at 50 W. We quote the standard, the class and the FET resistance on the confirmation, and where a replacement is offered the classification events and the inrush limit are compared before anything else.

The second point is the magnetic and the bridge, which decide the efficiency more than the controller does. A PoE transformer with the wrong turns ratio will not deliver the class power at the low end of the input range, and a silicon bridge instead of a Schottky or an ideal diode bridge costs several points of efficiency at 50 W. The controller, the transformer, the bridge and the input capacitor for one port are quoted as a set so the efficiency budget is calculated on real parts.

Where the PD boards are assembled in volume, SUPERB Assembly support covers the SMT build of the isolated section.

Q: Do you supply obsolete PoE PD controllers such as the MAX5941A?

A: Yes. Send the complete order code, the standard and class, the PD power and the converter topology, and the SUPERB Tech sales team will confirm availability and the transformer that matches.

Why Buyers Source PoE Parts Through SUPERB

  1. Standard and class on the quote: the 802.3 revision, the class and the FET resistance are stated per line, so the part matches the switch it will be plugged into.
  2. Controller and magnetics together: the transformer, the bridge and the input capacitor for one port are quoted as a set, so the efficiency figure is not an estimate.
  3. End of life stock: parts such as the MAX5941A are held with their date code, which keeps a camera or a phone in production while a replacement is qualified.
  4. Board build: where the PD board is assembled in volume, the SMT and test of the isolated section is handled by the same team that supplies the parts.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Power management ICs, Isolated DC-DC modules, Ethernet PHY and switch chips, Common mode chokes, BOM shortage recovery.