eMMC and NAND Flash Storage for Industrial Controllers
Product Specifications
Product Overview
Embedded storage splits into three families and each one solves a different problem. Managed eMMC has the controller, the bad block management and the wear levelling inside the package, so the host sees a block device and the firmware stays simple. Raw SLC NAND gives the lowest cost per bit for code and logging but puts bad block handling into the host. SPI NAND sits between the two and is used where a serial interface is all that is available but a few hundred megabytes are no longer enough.
Industrial boards tend to mix all three. The eMMC holds the operating system and the logs, the SLC NAND holds boot code or a configuration store that has to keep working after ten years of writes, and the SPI NAND holds a firmware image next to an FPGA. Long term availability is the constant requirement, and it is the part most often broken when a consumer grade device is specified on an industrial build.
All models are grouped into this single product, so a controller board can be quoted with its eMMC, its boot flash and the level shifting parts in one line. Tell us the density, the interface, the temperature grade and the package height available on the board, and the class can be matched to the mechanical allowance.
Key Specifications
| Parameter | Managed eMMC | Raw SLC NAND and SPI NAND |
|---|---|---|
| Density | 4 GB to 128 GB | 1 Gb to 8 Gb (128 MB to 1 GB) |
| Interface | MMC 5.0 and 5.1, x1, x4 and x8, HS200 and HS400 modes | Parallel x8 or x16 for raw NAND, SPI and quad SPI for serial NAND |
| Package | 153 ball FBGA, 11.5 x 13 mm, 1.0 mm to 1.2 mm high | TSOP-48 for parallel, WSON-8 and BGA-24 for serial |
| Supply | VCC 2.7 V to 3.6 V, VCCQ 1.7 V to 1.95 V or 2.7 V to 3.6 V | 3.0 V to 3.6 V single supply |
| Endurance | Wear levelling and bad block management inside the package | SLC cells rated for tens of thousands of erase cycles, host manages bad blocks |
| Temperature | -40 C to 85 C industrial grade, automotive grades on selected parts | -40 C to 85 C industrial |
| Protection | Boot partitions, replay protected memory block, secure erase, write protection | OTP region, block protection and lock registers |
| Typical role | Operating system, application and data logging | Boot code, configuration store, firmware image |
Included Models and Order Codes
The table lists the storage devices most often requested for industrial controllers. Send the complete order code including the temperature suffix and the packing option and we confirm availability against that exact string.
| Model | Type and Density | Interface | Package | Temperature | Notes |
|---|---|---|---|---|---|
| MTFC4GACAJCN-4M IT | Managed eMMC, 4 GB | MMC 5.0, x1 x4 x8, HS200 and HS400 | 153 ball VFBGA, 11.5 x 13 x 1.0 mm | -40 C to 85 C | Industrial grade, boot partition support |
| MTFC8GAKAJCN-4M IT | Managed eMMC, 8 GB | MMC 5.0, x1 x4 x8, HS200 and HS400 | 153 ball VFBGA, 11.5 x 13 x 1.0 mm | -40 C to 85 C | Same footprint as the 4 GB version |
| MTFC8GAMALBH-IT | Managed eMMC, 8 GB | MMC 5.1 | 153 ball TFBGA, 11.5 x 13 x 1.1 mm | -40 C to 85 C | Industrial eMMC 5.1 family |
| MTFC16GAPALBH-IT | Managed eMMC, 16 GB | MMC 5.1 | 153 ball TFBGA, 11.5 x 13 x 1.1 mm | -40 C to 85 C | Industrial eMMC 5.1 family |
| MTFC32GAPALBH-IT | Managed eMMC, 32 GB | MMC 5.1 | 153 ball TFBGA, 11.5 x 13 x 1.1 mm | -40 C to 85 C | Larger density in the same footprint |
| KLM8G1GETF-B041 | Managed eMMC, 8 GB | MMC 5.1, HS400 | 153 ball FBGA | -25 C to 85 C | Common choice on embedded controller boards |
| KLMAG1JENB-B041 | Managed eMMC, 16 GB | MMC 5.1, HS400 | 153 ball FBGA | -25 C to 85 C | Density upgrade in the same package family |
| THGBMJG6C1LBAIL | Managed eMMC, 8 GB | MMC 5.1 | 153 ball FBGA | -40 C to 85 C | Industrial temperature eMMC |
| THGBMJG8C4LBAU7 | Managed eMMC, 16 GB | MMC 5.1 | 153 ball FBGA | -40 C to 85 C | Industrial temperature eMMC |
| MT29F1G08ABAEAWP-IT:E | Raw SLC NAND, 1 Gb | Parallel x8, asynchronous | TSOP-48 | -40 C to 85 C | Boot code and configuration store |
| MT29F2G08ABAEAWP-IT:E | Raw SLC NAND, 2 Gb | Parallel x8, asynchronous | TSOP-48 | -40 C to 85 C | Code storage where the host manages bad blocks |
| MT29F4G08ABADAWP-IT:D | Raw SLC NAND, 4 Gb | Parallel x8, asynchronous | TSOP-48 | -40 C to 85 C | Common SLC density for industrial designs |
| MT29F8G08ABACAWP-IT:C | Raw SLC NAND, 8 Gb | Parallel x8, asynchronous | TSOP-48 | -40 C to 85 C | Largest SLC density in the TSOP-48 family |
| S34ML04G200TFI000 | Raw SLC NAND, 4 Gb | Parallel x8, 3 V | TSOP-48 | -40 C to 85 C | Industrial SLC NAND with on die ECC option |
| W25N01GVZEIG | SPI NAND, 1 Gb | SPI and quad SPI | WSON-8 | -40 C to 85 C | Firmware image and data logging over a serial interface |
| GD5F1GQ5UEYIGR | SPI NAND, 1 Gb | SPI and quad SPI | WSON-8 | -40 C to 85 C | Second source for the serial NAND footprint |
Key Features
Managed And Raw In One Place – eMMC for the operating system and raw SLC NAND for boot and logging, quoted from the same desk so the storage map of the board is covered in one enquiry.
Industrial Temperature Grades – Parts marked for -40 C to 85 C operation, which is what industrial controllers and outdoor equipment actually require.
Footprint Continuity – Densities that share the same 153 ball footprint can be changed on a board without touching the layout, which keeps a platform alive as image sizes grow.
Consistent Package Height – Package heights are quoted in the table because the 1.0 mm, 1.1 mm and 1.2 mm versions are not interchangeable where the enclosure has a fixed gap.
Long Life SLC Options – SLC cells tolerate far more erase cycles than consumer TLC, which is why they are still specified for configuration stores written every day.
Serial NAND For Small Boards – SPI and quad SPI NAND in WSON and BGA packages where a parallel bus is not available but a SPI NOR density is too small.
Batch And Status Stated – Each line states whether the parts are new and sealed or pulled and tested, and the batch information for traceability.
Applications
Boards where these storage parts are specified: Storage is usually quoted together with the SUPERB PCB and SUPERB PCBA work we support for the same controller, so the storage BOM does not become a separate project.
Industrial Controllers And HMI Panels – Controllers that run an operating system from eMMC and log process data where a consumer grade device would fail the qualification file.
Telecom And Networking Equipment – Line cards and gateways that need a boot image on SLC NAND and an application store on eMMC inside the same chassis.
Medical Instruments – Imaging and monitoring equipment where the storage has to be traceable and the temperature grade is part of the approval file.
Transport And Metering Loggers – Devices that write continuously for years and need the endurance of SLC cells with a documented supply path.
Sourcing and Cross-Reference
Storage devices turn over quickly: the same footprint is offered at several densities and the vendor moves a density to end of life without changing the part number on the board. That keeps the layout stable but makes stock the variable. We check the density against the current pipeline and state which densities are still available in industrial temperature.
Where a part has gone, the substitute has to match the interface, the package height, the boot behaviour and the temperature grade, and this is where most cross references fail. We compare those fields before proposing a replacement, and where the substitute needs a firmware change, a different boot partition layout or a different ECC scheme, that is stated with the quote.
SUPERB Assembly support covers the SMT build where the boards are assembled in volume.
Q: Can you supply an industrial temperature eMMC or SLC NAND that is no longer in the catalogue?
A: Yes. Send the order code and the quantity and the SUPERB Tech sales team will confirm availability and the nearest density in the same footprint.
Why Source Storage Devices from Superb Automation?
- Specialised Sourcing Focus: Memory, programmable logic and mixed signal devices for industrial, telecom, medical and defence builds, compared field by field with the drawing.
- Hard To Find And Obsolete Parts: Storage densities that leave production while the platform stays in service, sourced with the lifecycle status and batch information stated up front.
- Cross Reference Support: Interface, package height, boot behaviour, ECC scheme and temperature grade differences listed with the quote.
- Stock And Build Quantities: Prototype quantities, repair quantities and volume orders are all welcome, with the batch information stated per line.
- BOM Kitting: The storage device, the level shifters and the passive parts for the same board can be quoted together.
- Reply With Evidence: Documents, batch marking and the condition of the parts are stated on the quote before the order is placed.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: BOM Shortage Recovery, Multi-Function ICs, SPI NOR Flash Memory Chips for Embedded Firmware Storage, DDR3L and DDR4 SDRAM Chips for Embedded and Industrial Designs.