Logic Level Shifters and IO Expanders for Mixed Voltage Boards
Product Specifications
Product Overview
A mixed voltage board is normal now: a 1.8 V processor, a 3.3 V sensor and a 5 V legacy peripheral on the same PCB. Every signal that crosses between those domains needs a part that both shifts the level and survives the case where one rail is up and the other is still at ground. The choice comes down to four questions. Does the line need a direction pin, is the driver push-pull or open-drain, what data rate has to survive the translation, and what happens when either supply is removed.
The auto direction families answer the first question. The TXS0102 and TXS0104E work from 1.65 V to 3.6 V on the A side and 2.3 V to 5.5 V on the B side with integrated 10 kohm pull-ups, which suits I2C, SMBus and other open-drain buses at up to 2 Mbps and push-pull signals at up to 24 Mbps. The TXB0104 and TXB0108 cover the same voltage range for push-pull CMOS only and reach 100 Mbps, and the 8 bit TXS0108E adds a wider voltage range of 1.4 V to 3.6 V on the A side. Where only two lines are needed on an I2C bus, the PCA9306 does the job with a 3.5 ohm switch and no direction pin at all.
Direction controlled parts are used where the bus is wider or the speed is higher. The SN74LVC1T45 shifts one bit between any two supplies from 1.65 V to 5.5 V at up to 420 Mbps with a DIR pin, the SN74LVC2T45 does two bits, and the SN74LVC8T245 does eight bits with the same rails and 3-state outputs. The LSF0102 and LSF0108 sit between the two ideas: no direction pin, 5 V tolerant input and output, 0.9 V to 5.5 V on the low side, and mixed mode operation where each channel can be pulled to a different supply. For port count rather than level translation, the I2C expanders add 8 or 16 lines with an interrupt output, from the PCF8574 and the PCA9555 through to the MCP23017 and the MAX7313.
Key Specifications
| Parameter | Auto direction translators | Direction controlled transceivers | I2C and SMBus IO expanders |
|---|---|---|---|
| Channels | 2, 4 and 8 bit | 1, 2 and 8 bit | 8 and 16 ports |
| Supply range | 1.2 V to 3.6 V on the A side, 1.65 V to 5.5 V on the B side | 1.65 V to 5.5 V on both ports | 1.65 V to 5.5 V, and 2.5 V to 6 V on the PCF8574 |
| Direction control | None, edge rate accelerators sense the direction | DIR pin plus output enable | Not applicable, each port bit is set by the bus master |
| Data rate | 24 Mbps push-pull and 2 Mbps open-drain on the TXS parts, 100 Mbps on the TXB parts | 420 Mbps for a 3.3 V to 5 V translation, 24 mA drive at 3.3 V | 400 kHz bus, 100 kHz on the PCF8574 |
| Open-drain support | Yes, with integrated 10 kohm pull-ups | Push-pull output, an open-drain line needs an external pull-up and a direction check | Open-drain interrupt output |
| Supply isolation | If either supply is at ground both ports go high impedance | Same feature across the LVC dual rail family | Not applicable |
| Typical packages | 8 to 20 pin SM8, VSSOP, X2SON, TSSOP, UQFN | 6 pin SOT and SC70 up to 24 pin TSSOP and VQFN | 16 pin SOIC, 20 and 24 pin TSSOP and QFN |
| Operating temperature | -40 C to +85 C on the TXS and TXB families | -40 C to +125 C on the LSF family | -40 C to +85 C, and +125 C on selected expander grades |
Included Models and Order Codes
The table lists the parts most often requested for mixed voltage boards, from single bit translation up to 16 port expansion. Send the complete order code including the package suffix and we confirm availability against that string.
| Part Number | Function | Channels | Supply Range | Data Rate or Bus Speed | Package |
|---|---|---|---|---|---|
| TXS0102 | Auto direction translator, open-drain and push-pull | 2 bit | 1.65 V to 3.6 V A, 2.3 V to 5.5 V B | 24 Mbps push-pull, 2 Mbps open-drain | 8 pin SSOP, VSSOP, X2SON or DSBGA |
| TXS0102DQER | Smallest body order code of the same part | 2 bit | 1.65 V to 3.6 V A, 2.3 V to 5.5 V B | 24 Mbps push-pull, 2 Mbps open-drain | X2SON 1.4 x 1.0 mm |
| TXS0104E | Auto direction translator with integrated pull-ups | 4 bit | 1.65 V to 3.6 V A, 2.3 V to 5.5 V B | 24 Mbps push-pull, 2 Mbps open-drain | 14 pin TSSOP and QFN |
| TXS0108E | Wide range auto direction translator | 8 bit | 1.4 V to 3.6 V A, 1.65 V to 5.5 V B | 110 Mbps push-pull and 1.2 Mbps open-drain per current revision | 20 pin TSSOP, VQFN, VSSOP or UFBGA |
| TXB0104 | Auto direction translator for push-pull CMOS | 4 bit | 1.2 V to 3.6 V A, 1.65 V to 5.5 V B | 100 Mbps | 12 pin UQFN or DSBGA, 14 pin TSSOP or VQFN |
| TXB0108 | Auto direction translator for push-pull CMOS | 8 bit | 1.2 V to 3.6 V A, 1.65 V to 5.5 V B | 100 Mbps | 20 pin TSSOP, VQFN or VSSOP |
| PCA9306 | Dual bidirectional I2C and SMBus translator | 2 bit, SDA and SCL | 1.2 V to 3.3 V reference 1, 1.8 V to 5.5 V reference 2 | 400 kHz I2C, 3.5 ohm switch, no direction pin | 8 pin SSOP, VSSOP, X2SON or SO8 |
| LSF0102 | Auto bidirectional multi-voltage translator | 2 channel | 0.95 V to 5.5 V low side, 1.8 V to 5.5 V high side | 100 MHz up and above 100 MHz down at 30 pF load | 8 pin SM8, VSSOP, SOT-23, X2SON or DSBGA |
| LSF0108 | Auto bidirectional multi-voltage translator | 8 channel | 0.95 V to 5.5 V low side, 1.8 V to 5.5 V high side | 100 MHz up and above 100 MHz down at 30 pF load | 20 pin TSSOP, VSSOP or VQFN |
| SN74LVC1T45 | Direction controlled transceiver | 1 bit | 1.65 V to 5.5 V on both ports | 420 Mbps for 3.3 V to 5 V, 24 mA drive | 6 pin SOT, SOT-23, SC70, USON or DSBGA |
| SN74LVC2T45 | Direction controlled transceiver | 2 bit | 1.65 V to 5.5 V on both ports | 420 Mbps for 3.3 V to 5 V | 8 pin SM8, VSSOP or DSBGA |
| SN74LVC8T245 | Direction controlled bus transceiver | 8 bit | 1.65 V to 5.5 V on both ports | Direction and output enable control, 3-state outputs | 24 pin TSSOP and VQFN |
| ADG3304 | Bidirectional translator, no direction pin | 4 channel | 1.15 V to 5.5 V | 50 Mbps, quiescent current below 5 microamps | 14 lead TSSOP, 12 ball WLCSP, 20 lead LFCSP |
| ADG3308 | Bidirectional translator, no direction pin | 8 channel | 1.15 V to 5.5 V | 50 Mbps, three-state on both sides when disabled | 20 lead TSSOP or LFCSP |
| PCF8574 | I2C port expander, quasi bidirectional ports | 8 ports | 2.5 V to 6 V | 100 kHz I2C, open-drain interrupt, latched high current outputs | 16 pin SOIC, 20 pin TSSOP or QFN |
| PCA9555 | I2C and SMBus IO expander with interrupt | 16 ports | 2.3 V to 5.5 V | 400 kHz, open-drain interrupt output, configuration registers | 24 pin SO, TSSOP or HWQFN |
| TCA9535 | Low voltage version of the 16 port expander | 16 ports | 1.65 V to 5.5 V | 400 kHz, open-drain interrupt, no internal pull-up on the ports | 24 pin TSSOP, SSOP or VQFN |
| MCP23017 | I2C IO expander, AEC-Q100 qualified | 16 ports | 1.8 V to 5.5 V | 100 kHz, 400 kHz and 1.7 MHz modes, two interrupt pins | 28 pin QFN 6 x 6 mm, wide SOIC, SSOP or SPDIP |
| MCP23008 | 8 port version of the same expander family | 8 ports | 1.8 V to 5.5 V | 100 kHz, 400 kHz and 1.7 MHz modes, one interrupt pin | 18 pin SOIC or PDIP, 20 pin SSOP or QFN |
| MAX7313 | 16 port expander with LED intensity control | 16 ports | 2 V to 3.6 V | 400 kHz, 50 mA per port open-drain output, PWM intensity control | 4 x 4 mm TQFN |
| MAX7321 | I2C port expander with open-drain ports | 8 ports | 1.71 V to 5.5 V | 400 kHz, 20 mA sink per port, ports protected to 6 V | 16 pin QSOP or TQFN |
Key Features
Direction sensing on buses that turn around – the TXS and TXB parts need no direction pin, so an I2C or SMBus line that changes direction mid transfer is handled without a control signal from the processor
Push-pull and open-drain in one part – the TXS devices translate open-drain buses at up to 2 Mbps and push-pull signals at up to 24 Mbps, with the 10 kohm pull-ups already inside the package
420 Mbps when the bus is fast – the SN74LVC1T45, 2T45 and 8T245 translate between any two rails from 1.65 V to 5.5 V with a DIR pin and reach 420 Mbps on a 3.3 V to 5 V translation
Mixed mode on the LSF family – the LSF0102 and LSF0108 are switch type translators with 5 V tolerant input and output, so each channel can be pulled to its own supply level on the same die
High impedance when a rail is missing – the auto direction and dual rail parts put both ports into high impedance when either supply is at ground, which stops the backfeed that damages a half powered board
Port count with an interrupt line – the I2C expanders add 8 or 16 ports with an interrupt output, so keypad, status and control lines come back to the processor on two wires instead of sixteen GPIO pins
Applications
The translators and expanders are supplied for the boards below. A mixed voltage section is normally quoted with the SUPERB PCB and SUPERB PCBA work we support for the same board, so the translators, the expanders, the pull-up resistors and the assembly come from one source.
Mixed voltage control boards – a 1.8 V or 2.5 V processor driving 3.3 V and 5 V peripherals through auto direction translators, with the rail and the data rate matching the peripheral datasheet
I2C sensor and interface boards – level translation on the SDA and SCL lines with the PCA9306 or the LSF family, where the bus capacitance limit of 400 pF has to be respected on both sides of the translator
Keypad, status LED and control expansion – 8 and 16 port expanders with an interrupt output on front panels and instrument boards, including the AEC-Q100 qualified parts for automotive and the LED drive parts for indicator banks
Sourcing and Cross-Reference
Level translators and expanders are easy to substitute on paper and hard to substitute on a board. A part with a direction pin cannot replace an auto direction part on an I2C bus without a firmware change, a VSSOP body does not fit a SOIC land pattern, and a 1.7 MHz expander code is not interchangeable with a 400 kHz code even though the port count is the same.
We confirm the channel count, the supply range on each side, the direction control type and the package against the full order code, and where a code is out we quote the nearest option with the difference in data rate, drive strength or footprint stated in writing. Where a board is still in layout, we can also check the alternative packages of the same die before the land pattern is fixed.
Two pages cover the rest of the interface section. Pin to pin cross reference deals with footprint compatible options, and BOM shortage recovery explains how a stopped build is worked when the original code cannot be found.
For volume builds, SUPERB Assembly support covers the SMT assembly of the control and logic sections.
Q: Can you supply a level translator that keeps the same package when the suffix changes?
A: Yes. Send the complete order code including the package letter, the voltage on each side and the quantity, and the SUPERB Tech sales team will confirm availability and the nearest option with the same pinout.
Why Buy From Us
- Suffix and package confirmed: availability is checked against the complete order code, because the package letter is what the land pattern was built around
- Direction control matched: an auto direction part is never offered against a design that needs a DIR pin, and the reverse, so the firmware stays as written
- Data rate stated: the quotation gives the push-pull and open-drain data rates of the part offered so the bus timing can be checked before it is fitted
- Expanders grouped with the bus parts: the expander, the translator and the bus pull-up resistors for one board can be quoted on one line
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Multi-Function ICs, STM32F103 Mainstream MCUs for Industrial Control Boards, Digital Isolators for Industrial and Medical Interfaces, RS-485 and RS-232 Transceiver Chips for Industrial Interfaces.