Contact Us
  • Home
  • COMPONENTS
  • Clock Generators and Frequency Up-Converters for Optical Line Cards

Clock Generators and Frequency Up-Converters for Optical Line Cards

Clock generation and distribution parts for optical line cards and transponders 156.25 MHz and 106.25 MHz references, dual PLL generators, up-conversion to 900 MHz, fan-out All models listed below are combined into this single product for easy sourcing Samples, build quantities, alternatives and cross reference are supported
quote now

Product Specifications

Product Overview

A line card or a transponder needs a reference clock that is both the right frequency and quiet enough for the optics. 156.25 MHz and 106.25 MHz are the rates that most 10G, 40G and 100G designs work from, usually derived from a 25 MHz or 19.44 MHz source, and the jitter on that clock shows up directly in the recovered eye and in the receiver sensitivity. Once the clock exists it also has to reach several devices with the same quality, which is why generation and distribution are usually separate parts.

The parts on this page cover both stages. The AD9575 is a two output network clock generator with an integrated PLL and VCO that accepts a 19.44 MHz, 25 MHz or 25.78125 MHz crystal and produces 0.39 ps rms jitter between 12 kHz and 20 MHz at 156.25 MHz, with LVDS, LVPECL or LVCMOS output formats. The AD9577 adds a second PLL with fractional-N operation and covers 11.2 MHz to 200 MHz continuously, with most frequencies up to 637.5 MHz available, plus spread spectrum and frequency margining for boards that have to pass an emissions test or shift a link rate for margin testing.

Where the reference already exists at a low frequency, the AD9552 up-converts it: 6.6 MHz to 112.5 MHz in, up to 900 MHz out, with under 0.5 ps rms jitter and preset pin programmable ratios, or arbitrary ratios over a three wire serial port. It also accepts a crystal directly, which removes a separate oscillator from the board.

For fan-out, the AD9512 takes two inputs up to 1.6 GHz and distributes them to three LVPECL outputs at up to 1.2 GHz and two LVDS or CMOS outputs, each with its own divider that can be set to any integer from 1 to 32, phase select for coarse alignment between outputs and a 5-bit fine delay on one output. Additive jitter is 225 fs rms on the LVPECL outputs and 275 fs rms on the LVDS outputs, so a clock reaches four devices without being destroyed on the way.

Electrical Specifications

ParameterNetwork clock generator (AD9575)Dual PLL clock generator (AD9577)Frequency up-converter (AD9552)Clock distribution (AD9512)
FunctionTwo output clock generator with fully integrated PLL and VCOMulti-output clock generator with one integer-N and one fractional-N PLLOscillator frequency up-converter with on-chip VCOMulti-output clock distribution IC with programmable dividers and delay
Reference inputCrystal at 19.44 MHz, 25 MHz or 25.78125 MHzCrystal or reference clock, with an optional divide by two on the referenceCrystal and or external oscillator, 6.6 MHz to 112.5 MHzTwo differential inputs up to 1.6 GHz
Output frequencyFixed network clock outputs, including 156.25 MHz and 106.25 MHz11.2 MHz to 200 MHz continuous coverage, most frequencies from 200 MHz to 637.5 MHz availableOutputs up to 900 MHz, with preset pin programmable ratios or arbitrary ratios over the serial portThree LVPECL outputs to 1.2 GHz, two LVDS or CMOS outputs to 800 MHz or 250 MHz
Jitter0.39 ps rms from 12 kHz to 20 MHz at 156.25 MHz, and 0.15 ps rms from 1.875 MHz to 20 MHz460 fs rms on PLL1, 470 fs rms integer-N and 660 fs rms fractional-N on PLL2Under 0.5 ps rmsAdditive output jitter 225 fs rms on LVPECL and 275 fs rms on LVDS
Output format and fan-outLVDS, LVPECL or LVCMOS outputs, two outputs with two part models in the familyUp to four LVDS or LVPECL outputs, or up to eight LVCMOS outputs, plus one buffered CMOS reference outputPrimary output plus a secondary output that is either integer related to the primary or a copy of the referenceFive outputs in total, each with its own programmable divider
Divider, phase and delayIntegrated output dividers as listed in the datasheet for the selected part modelProgrammable output and feedback dividers, integrated loop filtersFrequency translation ratio set by pin strapping or programmed over the serial portFive dividers from 1 to 32, phase select for coarse delay between outputs, 5-bit fine delay with a full scale range up to 10 ns on one output
ProgrammabilityPin configured for the network rates it was built forTwo wire interface programmable output frequencies and formats, with two pin controlled frequency maps for marginingThree wire serial port, with preset ratios available without programmingFour wire or three wire serial control port
Spread spectrumNot providedDown spread from 0 to minus 0.5 percent on the fractional-N PLL, for reduced emissionsNot providedNot provided
Supply and power3.3 V operation, part of a two model family from a low starting price3.3 V operation, 1.02 W in LVDS operation and 1.235 W in LVPECL operationSingle 3.3 V supply, under 400 mW in most conditionsSerial port controlled, with a military temperature variant available as the AD9512-EP
PackageSmall form factor package, see the datasheet for the selected model40-lead 6 mm by 6 mm LFCSP5 mm by 5 mm package48-lead LFCSP

Included Models and Order Codes

The table covers the generation, conversion and distribution parts requested most often for line cards, transponders and clock inputs. Send the output frequency, the output format and the quantity, and we will confirm availability against the exact order code.

ModelFunctionReference InputOutputsJitterPackage
AD9575Network clock generator with integrated PLL and VCO, two outputsCrystal at 19.44 MHz, 25 MHz or 25.78125 MHzTwo outputs in LVDS, LVPECL or LVCMOS format, network rates including 156.25 MHz and 106.25 MHz0.39 ps rms at 156.25 MHz from 12 kHz to 20 MHzSee datasheet for the two part models
AD9577Clock generator with dual PLLs, spread spectrum and margining, I2C programmableCrystal or reference clockUp to four LVDS or LVPECL outputs, or up to eight LVCMOS outputs, plus one buffered CMOS reference output460 fs rms to 660 fs rms depending on PLL and mode40-lead 6 mm by 6 mm LFCSP
AD9552Oscillator frequency up-converter with on-chip VCOCrystal and or external oscillator from 6.6 MHz to 112.5 MHzPrimary output up to 900 MHz plus a secondary output, preset or arbitrary translation ratiosUnder 0.5 ps rms5 mm by 5 mm package
AD9512Clock distribution IC with dividers, phase select and delay adjustmentTwo differential inputs up to 1.6 GHzThree LVPECL outputs to 1.2 GHz and two LVDS or CMOS outputs, dividers from 1 to 32225 fs rms additive on LVPECL, 275 fs rms additive on LVDS48-lead LFCSP

Key Features

Line Rate References For Optical Boards – The AD9575 generates the 156.25 MHz and 106.25 MHz references that 10G, 40G and 100G designs work from, with a crystal as the only external frequency element.

Sub-Picosecond Jitter – 0.39 ps rms at 156.25 MHz from 12 kHz to 20 MHz on the network generator and under 0.5 ps rms on the up-converter, which keeps the clock contribution small against the rest of the optical budget.

Dual PLL With Spread Spectrum And Margining – The AD9577 provides one integer-N and one fractional-N PLL, continuous coverage from 11.2 MHz to 200 MHz, down spread of 0 to minus 0.5 percent for emissions, and two pin controlled frequency maps for margin testing a link.

Crystal Based Up-Conversion To 900 MHz – The AD9552 turns a low frequency reference into an output up to 900 MHz, with preset ratios set by pin strapping or arbitrary ratios programmed over the serial port, so one board can serve several frequency plans.

Fan-Out Without Losing The Clock – The AD9512 distributes an input up to 1.6 GHz to five outputs with additive jitter of 225 fs rms on LVPECL and 275 fs rms on LVDS, which is what makes it possible to clock several converters from one source.

Programmable Dividers And Timing Adjust – Five dividers from 1 to 32, phase select for coarse delay between outputs and a 5-bit fine delay with a full scale range up to 10 ns let a multi-clock board be aligned in firmware rather than in layout.

Integrated Loop Filters And Serial Control – Both generator parts include their loop filters, and programming is over a two wire interface on the AD9577, a three wire serial port on the AD9552 and a four wire or three wire port on the AD9512, so no external loop components have to be tuned.

Military Temperature Option – The AD9512-EP covers minus 55 C to plus 85 C with a controlled baseline, one assembly and test site and qualification data available on request, for defence and aerospace boards.

Applications

Boards where these parts are used: Timing sections are generally quoted alongside the SUPERB PCB and SUPERB PCBA work we support, so the generator, the distribution part, the regulators and the assembly arrive together.

Optical Line Cards And Transponders – OTN, DWDM and muxponder boards that need a line rate reference and a fan-out to several converters and framers.

Optical Module And Transmitter Reference Clocks – Module and daughtercard designs that take a low frequency reference and up-convert it to the rate the optics need.

Test Instruments And Clock Sources – Measurement equipment where the clock is part of the specification and jitter has to be known rather than assumed.

Telecom And Industrial Timing Boards – Distribution and timing cards that fan a single reference out to many devices and need per-output dividers and delay adjustment.

Sourcing and Cross-Reference

Clock parts stay in production for a long time, which is exactly why they are a sourcing problem when a line card is still being built and the generator is no longer stocked. Boards are usually tied to the register map of the part they were laid out with, so a substitute has to match the output formats, the supply, the loop filter arrangement and the programming interface before it can be considered.

We check the exact order code, the package and the revision level before quoting, and we state which specification differs when we propose an alternative. Where the pinout and the register map are the same inside a family, the swap is straightforward and we say so. Where the jitter, the output format or the number of outputs changes, that is written on the quote as well, because it affects the optical margin rather than only the bill of materials. Clock parts are also quoted with the regulators and the passives for the same timing section, so one delivery covers the whole block.

SUPERB Assembly support covers the SMT build of the timing and line card section where the board is assembled in volume.

Q: Can you supply a clock generator for a line card when the usual distributor no longer stocks it?

A: Yes. Send the part number, the output format and the quantity and the SUPERB Tech sales team will check availability and propose the nearest member of the family.

Why Source Timing Parts from Superb Automation?

  1. Timing And Interface Focus: Clocking, conversion and distribution parts for telecom and optical boards, quoted against the specification that matters rather than the headline frequency.
  2. Long Life Support: Parts for boards that stay in production for a decade, with the availability of the exact revision checked before the quote is issued.
  3. Cross Reference With Real Limits: Output format, jitter, supply and register map differences are stated, because those are the points where a timing substitute fails.
  4. Stock, Samples And Build Quantities: Engineering samples, repair quantities and production volumes are all handled, with batch information stated per line.
  5. One Delivery Per Board Section: Clock, power and interface parts for the same block can be quoted together, which keeps the incoming inspection down to one kit.
  6. Documents With The Quote: Package, marking and condition are confirmed before the order is placed, and military temperature variants are quoted where a project needs them.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Frequency Converters and Sources, ADI Clock and Data Recovery Chips, Component Sourcing and Supply, Components.