Digital Isolators for Industrial and Medical Interfaces
Product Specifications
Product Overview
Isolation is specified by the safety requirement, not by the interface. A 2.5 kV rms part and a 5 kV rms part can have the same logic function and the same pinout, and the difference only shows up when the barrier is reviewed. The other numbers that decide whether an isolator works are the common mode transient immunity, the propagation delay and its matching between channels, and the current taken per channel on a board that has to run from a limited rail.
This page groups the isolators we supply along those lines. The general purpose parts provide two or four channels at 25 Mbps with 45 ns maximum propagation delay, 3 ns pulse width distortion and UL recognition at 2500 V rms, with common mode transient immunity above 25 kV per microsecond. The quad channel families go further: up to 150 Mbps with propagation delay below 10 ns, isolation ratings of 1.0 kV, 2.5 kV, 3.75 kV and 5.0 kV rms in the same footprint families, and a minimum pulse width of 5 ns so short pulses survive the crossing.
For medical equipment the reinforced parts are the ones that matter. The 5000 V rms wide body devices are rated to 12.8 kV surge, hold common mode transient immunity of 85 kV per microsecond minimum and 100 kV per microsecond typical, and carry 60601-1 recognition up to 250 V rms working voltage with two means of patient protection. For a service port or an instrument front end, the USB isolator covers low and full speed USB 2.0 at 1.5 Mbps and 12 Mbps with 5 kV rms isolation and 645 V peak working voltage, so a monitor can be connected to a host without a ground loop.
Key Specifications
| Parameter | General Purpose Isolators | High Speed Quad Channel | Reinforced and Medical |
|---|---|---|---|
| Channels | 2 or 4 channels, 2/0, 1/1, 4/0, 3/1 and 2/2 arrangements | 4 channels in 4/0, 3/1 and 2/2 arrangements | 4 channels, plus USB front ends |
| Data rate | Up to 25 Mbps | Up to 100 Mbps, 150 Mbps in the Si864x and ISO644x families | Up to 100 Mbps |
| Isolation rating | 2500 V rms per UL 1577 | 1.0 kV, 2.5 kV, 3.75 kV and 5.0 kV rms options | 5000 V rms, 3000 V rms in the small body |
| CMTI | Above 25 kV per microsecond | 85 kV per microsecond minimum, 100 kV per microsecond typical | 85 kV per microsecond minimum |
| Propagation delay | 45 ns maximum at 5 V, 3 ns pulse width distortion | 10.7 ns typical, 17 ns maximum, 4 ns channel to channel skew | 10.7 ns typical |
| Supply | 2.7 V to 5.5 V per side, level translation across the barrier | 2.25 V to 5.5 V per side | 2.25 V to 5.5 V per side |
| Current per channel | Low power CMOS, supply current stated per data rate | 1.5 mA per channel at 1 Mbps, 0.9 mA DC | Under 120 uA per Mbps dynamic in the low power parts |
| Temperature | -40 C to +105 C by part | -40 C to +125 C | -55 C to +125 C |
Included Models and Order Codes
The table lists the isolator part codes most often requested for control, fieldbus, instrument and medical boards. Send the complete order code including channel direction and package and we confirm availability against that string.
| Part Number | Channels | Data Rate | Isolation | Package | Notes |
|---|---|---|---|---|---|
| ADuM1200CRZ | 2 channels, both in one direction | 25 Mbps | 2500 V rms, UL 1577 | SOIC-8 | 45 ns maximum propagation delay at 5 V, 3 ns pulse width distortion |
| ADuM1201CRZ | 2 channels, one each direction | 25 Mbps | 2500 V rms, UL 1577 | SOIC-8 | Bidirectional pair for UART and SPI style links |
| ADuM1201WURZ | 2 channels, one each direction | 25 Mbps | 2500 V rms | SOIC-8 | W grade part for wider temperature operation |
| ADuM1400 | 4 channels, all in one direction | 25 Mbps class | 2500 V rms per UL 1577 | SOIC-16 wide body | Common mode transient immunity above 25 kV per microsecond |
| ADuM1401 | 4 channels, three forward and one reverse | 25 Mbps class | 2500 V rms | SOIC-16 wide body | The usual arrangement for SPI and converter interfaces |
| ADuM1402 | 4 channels, two each direction | 25 Mbps class | 2500 V rms | SOIC-16 wide body | For UART plus handshake lines across a barrier |
| ADuM4160BRWZ | USB 2.0 low and full speed front end | 1.5 Mbps and 12 Mbps | 5000 V rms for 1 minute | SOIC-16 wide body | 645 V peak working voltage, above 25 kV per microsecond CMTI, 105 C operation |
| ADuM3160 | USB 2.0 low and full speed front end | 1.5 Mbps and 12 Mbps | 2500 V rms | SOIC-16 wide body | Lower isolation version of the same USB isolator platform |
| Si8640 | 4 channels, all forward | Up to 150 Mbps | 1.0 kV to 5.0 kV rms options | QSOP-16, SOIC-16 | Propagation delay below 10 ns, 5 ns minimum pulse width |
| Si8641 | 4 channels, three forward and one reverse | Up to 150 Mbps | 1.0 kV to 5.0 kV rms | QSOP-16, SOIC-16 | 1.5 mA per channel at 1 Mbps, -40 C to +125 C |
| Si8642 | 4 channels, two each direction | Up to 150 Mbps | 1.0 kV to 5.0 kV rms | QSOP-16, SOIC-16 | 2 ns propagation delay skew, automotive order codes available |
| Si8642BD-B-IS | 4 channels, two each direction | 150 Mbps | 5000 V rms | SOIC-16 wide body | Wide body option for reinforced barriers |
| ISO7740 | 4 channels, all forward | 100 Mbps | 5000 V rms in DW-16, 3000 V rms in DBQ-16 | SOIC-16 wide body or QSOP-16 | Default output high, 10.7 ns typical propagation delay |
| ISO7741 | 4 channels, three forward and one reverse | 100 Mbps | 5000 V rms in DW-16, 3000 V rms in DBQ-16 | SOIC-16 wide body or QSOP-16 | 85 kV per microsecond minimum CMTI, 12.8 kV surge capability |
| ISO7742 | 4 channels, two each direction | 100 Mbps | 5000 V rms in DW-16 | SOIC-16 wide body | Supply range 2.25 V to 5.5 V with level translation |
| ISO7741B | 4 channels, three forward and one reverse | 100 Mbps | 5000 V rms | SOIC-16 wide body | Basic insulation version for boards that do not need reinforced rating |
| ISO7041 | 4 channels, ultra low power | Low power part for slow interfaces | Standard isolation rating for the family | SOIC-16 | Under 120 uA per Mbps dynamic current and 3.5 uA static per channel at 3.3 V |
| ISO6441 | 4 channels, three forward and one reverse | 150 Mbps | Reinforced insulation, narrow body | SOIC-16 narrow | 250 kV per microsecond CMTI, cost optimised package |
Key Features
Isolation rating named per order code – 1.0 kV, 2.5 kV, 3.75 kV and 5.0 kV rms options are listed separately because the barrier review depends on the exact rating
CMTI quoted as a minimum – 25 kV per microsecond on the general purpose parts and 85 kV per microsecond minimum on the reinforced ones, which is the number that survives a switching edge
Channel direction fixed by part number – forward and reverse arrangements are separate order codes, so the signal direction on the board is not left to a jumper or a software setting
Propagation delay and skew documented – 45 ns maximum on the general purpose parts, 10.7 ns typical with 4 ns skew on the high speed quad channel parts
Medical recognition – 60601-1 recognition up to 250 V rms working voltage with two means of patient protection on the reinforced families
Low power channels for constrained rails – per channel dynamic current under 120 uA per Mbps in the low power family for loop powered and battery backed boards
Applications
The parts are supplied for the boards below. Isolation is normally quoted with the SUPERB PCB and SUPERB PCBA work we support for the same board, so the barrier parts, the transceivers and the isolated supply arrive together.
Industrial control and fieldbus – isolated SPI, UART and CAN links between a controller and a field stage, and isolated digital IO on PLC style boards
Medical monitoring equipment – patient connected front ends on monitors and diagnostic equipment where 60601-1 reinforced isolation and two means of patient protection are required
Instruments and service ports – isolated USB links between an instrument and a host, and isolated conversion interfaces on test equipment
Sourcing and Cross-Reference
Isolator substitutions are only safe when the barrier is checked. A 2.5 kV rms part swapped for a 5 kV rms part in the same package is an improvement, but the reverse changes the safety case, and a different channel direction arrangement reverses a signal that the board cannot see.
We confirm availability against the complete order code including channel direction, isolation rating and package, and where a code is short we quote the nearest option with the isolation rating, CMTI and current per channel stated in writing so the barrier and the timing budget can be rechecked before the part is released.
Where the boards are assembled in volume, SUPERB Assembly support covers the SMT build of the isolated section.
Q: Can you supply an isolator with the same channel direction and isolation rating?
A: Yes. Send the order code, the channel direction and the isolation rating and the SUPERB Tech sales team will confirm availability and the nearest part in the same package.
Why Buy From Us
- Channel direction checked: forward and reverse channel arrangements are confirmed against the order code so a signal is not reversed by a substitution
- Isolation rating and package named: the exact rating and body are quoted because the barrier review depends on both
- Timing data provided: propagation delay, pulse width distortion and channel skew are supplied with the quotation for interfaces where the edge timing matters
- Isolators grouped with the interface parts: isolators, transceivers and the isolated supply parts can be quoted on one line so the interface section is complete
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Multi-Function ICs, RS-485 and RS-232 Transceiver Chips, CAN Bus Transceivers and Controllers, Pin to Pin Cross Reference.