TVS and ESD Protection Diodes for Telecom and Industrial Interfaces
Product Specifications
Product Overview
Every connector, cable run and long trace on a telecom or industrial board is an entry point for a surge. The two events that damage parts most often are the human body discharge at a mating connector and the slower 8/20 microsecond surge induced on a cable, and the parts that deal with them are not the same. A steering diode array with a fraction of a picofarad of loading protects a 3 Gbps differential pair; a 1500 W transient suppressor protects the rails and the long field wiring behind it.
The low capacitance arrays on this page are chosen by the interface they sit on. The RClamp0524P presents 0.3 pF typical between input pins, which keeps it usable above 3 GHz, and the TPD4E05U06 stays at 0.5 pF while covering four lines at a 5.5 V working voltage. Where the line is slower but carries more energy, the SLVU2.8 and SLVU2.8-4 sit at 2.8 V with 400 W of peak pulse power and 5 pF typical per line, which is the usual choice on 10/100 Ethernet pairs and on the analog inputs of line cards. All of them are rated to IEC 61000-4-2 level 4 and take at least 40 A of electrical fast transient.
The second group is the discrete suppressors and the bus specific parts. Stand off voltage decides the choice, so an RS-485 port that swings to 12 V needs the asymmetrical SM712 with its 12 V and 7 V working voltages rather than a symmetrical 5 V part, and a CAN node that can see a 24 V power cross needs the NUP2105L or the CDSOT23-T24CAN at 24 V. For power entry and long wiring the SMAJ, SM6T and SMCJ lines cover 400 W, 600 W and 1500 W of peak pulse power at the 10/1000 microsecond waveform, with clamping voltages low enough to stay inside the absolute maximum ratings of the part behind them.
Key Specifications
| Parameter | Low capacitance ESD arrays | Discrete surge TVS and bus protectors |
|---|---|---|
| Working voltage | 2.8 V to 24 V | 5 V to 33 V and above |
| Peak pulse power | 130 W to 600 W at 8/20 microseconds | 400 W to 1500 W at 10/1000 microseconds |
| Capacitance per line | 0.3 pF to 75 pF maximum | Not the selection limit on a power or bus line |
| ESD rating | IEC 61000-4-2 level 4, up to 30 kV contact on the protected pins | Level 4 on the array versions, surge rated on the discrete parts |
| Surge rating | 5 A to 24 A at 8/20 microseconds | 28 A to 43 A at 10/1000 microseconds |
| EFT rating | 40 A at 5/50 nanoseconds | Not normally specified |
| Typical packages | SOT-23, SO-8, SLP2510P8, USON-10, SOD-323 | SMA, SMB and SMC surface mount, plus SOT-23 for the bus parts |
| Operating temperature | -55 C to +150 C | -65 C to +150 C on the SMAJ family |
Included Models and Order Codes
The table lists the protection parts most often requested for line interfaces and power entry. Send the complete order code including the reel suffix, and state the working voltage the port sees in normal operation, and we confirm availability against that string rather than against the series name.
| Part Number | Device Type | Lines | Working Voltage | Key Ratings | Package |
|---|---|---|---|---|---|
| SM712-02HTG | Asymmetrical TVS array for RS-485 and fieldbus | 2 data lines | 12 V and 7 V | 600 W peak pulse at 8/20 microseconds, 19 A, 75 pF maximum line to ground | SOT-23-3 |
| CDSOT23-SM712 | Dual TVS array, same RS-485 function | 2 data lines | 7 V and 12 V | Minimum breakdown 7.5 V and 13 V, low capacitance | SOT-23 |
| NUP2105L | Dual bidirectional CAN bus protector | 2 bus lines | 24 V | 350 W per line, 8 A at 8/20 microseconds, clamps 40 V at 5 A, 30 pF maximum | SOT-23 |
| NUP2105LT1G | Same device, tape and reel order code | 2 bus lines | 24 V | 350 W per line, 16 kV human body model, 30 kV IEC 61000-4-2 contact | SOT-23 |
| SZNUP2105LT1G | Automotive grade CAN protector, AEC-Q101 | 2 bus lines | 24 V | 350 W per line, 30 kV contact discharge, PPAP capable | SOT-23 |
| CDSOT23-T24CAN | CAN protector, dual TVS array | 2 bus lines | 24 V | 8 A at 8/20 microseconds, clamps 36 V at 5 A, 22 pF line to ground, 11 pF line to line | SOT-23 |
| TPD4E05U06DQAR | 4 channel unidirectional ESD protection array | 4 lines | 5.5 V | 0.5 pF per line, 6.5 V minimum breakdown, interfaces up to 6 Gbps | USON-10 |
| TPD1E05U06 and TPD6E05U06 | Same diode in 1 channel and 6 channel versions | 1 and 6 lines | 5.5 V | Same 6.5 V minimum breakdown and low line capacitance | Leadless small outline |
| RClamp0524P | 4 line ultra low capacitance TVS array | 4 lines | 5 V | 0.3 pF typical input to input, 5 A at 8/20 microseconds, 40 A EFT, usable above 3 GHz | SLP2510P8, 2.5 x 1.0 x 0.58 mm |
| RClamp0522P | 2 line version of the same array | 2 lines | 5 V | 0.3 pF typical, 15 kV air and 8 kV contact per IEC 61000-4-2 | SLP1610P4, 1.6 x 1.0 x 0.58 mm |
| SLVU2.8 | Single line low voltage EPD suppressor | 1 line | 2.8 V | 400 W at 8/20 microseconds, 24 A surge, 15 kV air and 8 kV contact ESD | SOT-23 |
| SLVU2.8-4 | Four line low voltage EPD array | 4 lines, two pairs | 2.8 V | 400 W at 8/20 microseconds, 5 pF typical per line, flow through pinout | SO-8 |
| SLVU2.8-8 | Eight line low voltage EPD array | 8 lines, four pairs | 2.8 V | 600 W at 8/20 microseconds, 30 A surge, protects four line pairs | SO-8 |
| PESD5V0S1BA | Bidirectional ESD protection diode, one line | 1 line | 5 V | 130 W peak pulse power, clamps 14 V at 12 A, 45 pF maximum, above 30 kV ESD | SOD323, SC-76 |
| PESD5V0S1BB | Smaller body version of the same diode | 1 line | 5 V | Same 130 W rating and 14 V clamping voltage | SOD523, SC-79 |
| PESD5V0S1BL | Smallest body version of the same diode | 1 line | 5 V | Same electrical ratings in a leadless body | SOD882 |
| SMAJ5.0A | Unidirectional surge suppressor | 1 line | 5 V | 400 W at 10/1000 microseconds, 43.5 A, clamps 9.2 V, breakdown from 6.4 V | SMA, DO-214AC |
| SMAJ12A to SMAJ33A | Other voltages in the same series | 1 line | 12 V to 33 V | 400 W at 10/1000 microseconds, 600 W on stacked die versions | SMA, DO-214AC |
| SM6T6V8A and SM6T series | Transil surge suppressor | 1 line | 5.8 V and above | 600 W at 10/1000 microseconds, 4 kW at 8/20 microseconds, breakdown 6.8 V to 220 V | SMB, DO-214AA |
| SMCJ33A | High power unidirectional suppressor | 1 line | 33 V | 1500 W at 10/1000 microseconds, 28.2 A, clamps 53.3 V, breakdown from 36.7 V | SMC, DO-214AB |
Key Features
Capacitance quoted for the interface, not the family – 0.3 pF on the RClamp0524P, 0.5 pF on the TPD4E05U06 and 75 pF maximum on the SM712, so a high speed pair is not loaded by a part that was chosen for its surge rating alone
Asymmetrical working voltages for RS-485 – the 12 V and 7 V stand off of the SM712 follows the common mode range of an RS-485 port, which a symmetrical 5 V suppressor cannot do without conducting on normal signals
24 V parts for CAN and industrial buses – the NUP2105L and the CDSOT23-T24CAN hold off 24 V so they survive a power cross on the bus without clamping the normal signal, and the AEC-Q101 versions cover automotive builds
Clamping voltage stated at a current – each part is listed with the clamping voltage at a defined test current, which is the figure that decides whether the transceiver behind it stays inside its own limits
Footprints chosen to keep inductance low – the SLVU2.8-4 uses a flow through SO-8 layout and the RClamp parts are leadless, so the trace inductance in the protection path stays small and the clamp is reached faster
Protection for one port on one purchase line – the suppressor, the transceiver and the passives for the same port can be quoted together so the interface section is complete before the order is placed
Applications
The protection parts are supplied for the interfaces below. The protection parts for a board are normally quoted together with the SUPERB PCB and SUPERB PCBA work we support for that same board, so the small diodes, the transceivers and the assembly arrive as one order.
RS-485, fieldbus and industrial serial ports – SM712 and CDSOT23-SM712 arrays ahead of the transceiver, matched to the 12 V common mode range of the port
CAN and CAN FD nodes – 24 V bidirectional protectors on each bus line, with the automotive grades available where the board is qualified to AEC-Q101
Ethernet, telecom and line card interfaces – SLVU2.8-4 on 10/100 pairs, RClamp0524P on high speed differential pairs, and gated thyristor protectors such as the TISP and SIDACtor families ahead of a line transformer or a SLIC driver
Sourcing and Cross-Reference
Protection parts fail from the wrong stand off voltage or the wrong footprint far more often than from a missing rating. A 5 V array in a 12 V port conducts on every normal signal, and a 75 pF part on a multi gigabit pair closes the eye. What has to be confirmed is the exact order code including the reel suffix, the stand off voltage and the package, because those three are what the layout and the qualification were based on.
We supply these parts against the complete order code, and where a code is not available we quote the nearest option with the capacitance, the stand off voltage or the clamping difference stated in writing before the order is placed. Second source mapping between equivalent arrays from different suppliers is part of the same check, and batch and date code information comes with the quotation.
Where a build is held up by one of these parts, the process we use for BOM shortage recovery explains how the shortage is worked, and pin to pin cross reference covers the footprint compatible options across suppliers.
Where the boards are assembled in volume, SUPERB Assembly support covers the SMT build of the interface and protection sections.
Q: Can you supply pin-to-pin replacements for discontinued protection diodes?
A: Yes. Send the complete part number including the reel suffix, the stand off voltage you need and the quantity, and the SUPERB Tech sales team will confirm availability and the nearest option in the same package.
Why Buy From Us
- Order code level confirmation: availability is checked against the complete part number including the reel suffix and the package, not against the series name
- Stand off and clamping stated: the quotation lists the working voltage and the clamping voltage at the test current so the limits of the part behind it can be rechecked
- Cross reference before substitution: where a code is out, the nearest part in the same footprint is quoted with the capacitance and rating difference written down
- Batch and date code on request: batch information and date codes are provided with the quotation for boards that are already qualified
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Discrete and Power Semiconductors, RS-485 and RS-232 Transceiver Chips for Industrial Interfaces, CAN Bus Transceivers and Controllers for Automotive and Industrial Networks, BOM Shortage Recovery.