Ethernet PHY and Switch Chips for Industrial Networking
Product Specifications
Product Overview
Industrial networking boards usually need one of three things: a single port PHY next to a processor that already has a MAC, a multi port switch that connects several nodes inside a machine, or a hardware TCP offload device that lets a small microcontroller serve an Ethernet connection without a full network stack in software. The interface between the PHY and the host, MII, RMII, GMII or RGMII, is what usually decides the part rather than the data rate.
The parts on this page cover the range used on line cards, gateways, motor drives, measurement systems and building controllers. Devices with integrated termination and an internal regulator reduce the external part count, and the diagnostics features matter during commissioning: cable length measurement, TDR based fault location and parametric pin testing all shorten the time between a board arriving and a link coming up at the right speed.
All models are grouped into this single product, so a board can be quoted with the PHY, the magnetics, the crystal and the RJ45 in one line. Tell us the MAC interface type, the port count, the supply rails available and the temperature grade, and the device class can be matched to the host rather than reworking the interface around the device.
Key Specifications
| Parameter | Single Port PHY Devices | Switch and Offload Devices |
|---|---|---|
| Port speed | 10/100 Mbps and 10/100/1000 Mbps | 10/100 Mbps and gigabit, 3 to 7 ports |
| Host interface | MII, RMII, GMII, RGMII, SGMII on selected parts | MII, RMII, RGMII and SPI for the offload parts |
| Management | MDC and MDIO register interface, interrupt pin | MDIO and serial interfaces, managed and unmanaged options |
| Diagnostics | Cable length and TDR fault location, loopback, parametric pin testing | Per port link, activity and speed indication, VLAN and QoS registers |
| Supply | 1.2 V core with 1.8 V, 2.5 V or 3.3 V IO, integrated regulator on many parts | Single 3.3 V or 2.5 V supply with integrated regulator |
| Temperature | -40 C to 85 C industrial, up to 105 C and AEC-Q100 on selected parts | -40 C to 85 C industrial |
| Packages | 24 pin, 32 pin, 40 pin and 48 pin QFN, 48 pin LQFP | 48 pin LQFP, 128 pin LQFP and PQFP |
| Timing | 25 MHz crystal or clock input, 125 MHz clock output option | 25 MHz crystal with internal PLL |
Included Models and Order Codes
The table lists the networking devices most often requested for industrial, telecom and embedded boards. Send the complete order code including the temperature suffix and the packing option and we confirm availability against that exact string.
| Model | Speed | Host Interface | Package | Temperature | Notes |
|---|---|---|---|---|---|
| DP83848IVVX/NOPB | 10/100 Mbps | MII and RMII | 48 pin LQFP | -40 C to 85 C | Industrial single port PHY, cable diagnostics |
| DP83848KSQ/NOPB | 10/100 Mbps | MII and RMII | Smaller QFN package | -40 C to 85 C | Space constrained version of the same family |
| DP83822IFRHBR | 10/100 Mbps | MII, RMII, RGMII | 32 pin VQFN | -40 C to 85 C | Copper and fibre support, fibre diagnostics |
| DP83867IRPAPR | 10/100/1000 Mbps | RGMII | 64 pin HTQFP | -40 C to 85 C | Gigabit PHY with integrated termination |
| KSZ8081RNBIA | 10/100 Mbps | RMII | 24 pin QFN | -40 C to 85 C | Small RMII PHY for processor MACs |
| KSZ8081MNXIA | 10/100 Mbps | MII | QFN | -40 C to 85 C | MII version of the KSZ8081 family |
| KSZ9031RNXIA | 10/100/1000 Mbps | RGMII | 48 pin QFN, 7 x 7 mm | -40 C to 85 C | Triple speed PHY, LinkMD cable diagnostics, 16 KB jumbo frames |
| KSZ9031RNXCC | 10/100/1000 Mbps | RGMII | 48 pin QFN, 7 x 7 mm | 0 C to 70 C | Commercial temperature version of KSZ9031 |
| RTL8211F-CG | 10/100/1000 Mbps | RGMII | QFN | -40 C to 85 C | Gigabit PHY used on many embedded processor boards |
| VSC8541XMV-02 | 10/100/1000 Mbps | RGMII and GMII | QFN | -40 C to 85 C | Industrial gigabit PHY with IEEE 1588 support options |
| LAN8720A-CP-TR | 10/100 Mbps | RMII | 24 pin QFN | 0 C to 70 C | Low cost RMII PHY, small external part count |
| LAN8742A-CZ-TR | 10/100 Mbps | RMII | 24 pin QFN | -40 C to 85 C | Industrial version of the LAN87xx family, wake on LAN |
| LAN8710A-EZC-TR | 10/100 Mbps | MII and RMII | QFN | -40 C to 85 C | Widely used 10/100 PHY with auto MDIX |
| KSZ8863RLL | 10/100 Mbps, three port switch | Two MAC interfaces plus one PHY | 48 pin LQFP | -40 C to 85 C | Three port switch for daisy chained machines |
| KSZ8895RQXI | 10/100 Mbps, five port switch | Five PHY ports | PQFP | -40 C to 85 C | Unmanaged switch with per port status |
| KSZ9897RTXI | 10/100/1000 Mbps, seven port switch | Gigabit ports with RGMII and SGMII options | LQFP | -40 C to 85 C | Managed gigabit switch for industrial backbones |
| W5500 | 10/100 Mbps, MAC, PHY and TCP offload | SPI host interface | 48 pin LQFP | -40 C to 85 C | Hardware TCP/IP stack for small controllers |
Key Features
Interface Matched To The MAC – MII, RMII, GMII and RGMII options in the same families, so a processor interface can be served without adding glue logic or a second clock domain.
Single Port To Seven Port Coverage – One PHY for a controller board, a three port switch for a machine with a daisy chain, and a managed seven port device for a cabinet backbone.
Diagnostics That Save Commissioning Time – Cable length measurement, TDR fault location and parametric pin testing mean a wiring fault can be identified from the board instead of by substitution.
Fewer External Parts – Integrated termination resistors and an internal regulator remove the external resistor network and the second supply rail from the board.
Industrial Temperature Grades – Parts specified over -40 C to 85 C, with 105 C and AEC-Q100 options for equipment that runs in an enclosure or a vehicle.
Offload For Small Controllers – Devices with a hardware TCP/IP stack let a small microcontroller serve Ethernet with a serial host interface and no full network stack in firmware.
Long Life Networking Parts – Devices that stay in production for many years keep a fixed function controller or a line card alive without a redesign.
Applications
Boards where these devices are specified: A port is normally quoted with the SUPERB PCB and SUPERB PCBA work we support, so the PHY, the magnetics and the connector arrive as one line.
Industrial Controllers And Gateways – Controllers and protocol gateways that connect field devices to a plant network, where a stable link and a known PHY register set matter.
Telecom And Line Card Interfaces – Line cards and management interfaces that need a gigabit PHY with diagnostics and a defined temperature grade.
Measurement And Automation Equipment – Instruments and machine controllers that use a switch device to bring several nodes into one enclosure.
Remote Monitoring And Metering – Nodes that report on an interval and use an offload device to keep the host controller small and the firmware simple.
Sourcing and Cross-Reference
Ethernet parts change less in form than in availability: a device that fits a 24 pin QFN footprint can go on allocation while a device with the same function in a 48 pin package stays free. Because the host interface is not always the same between them, a substitute usually costs a board change rather than just a part number change.
We check the interface type, the boot strap pin defaults, the management interface and the crystal requirement before a substitute is proposed, and we state whether the parts are new and sealed or pulled and tested. For legacy boards, the exact order code including the temperature suffix is matched first, and the difference between the commercial and industrial version is stated rather than assumed.
For volume builds, SUPERB Assembly support covers the SMT assembly of the interface board.
Q: Can you supply an industrial temperature Ethernet PHY or switch that is hard to find?
A: Yes. Send the order code, the temperature suffix and the quantity and the SUPERB Tech sales team will confirm availability and the nearest part in the same family.
Why Source Networking Devices from Superb Automation?
- Specialised Sourcing Focus: Networking, memory and mixed signal devices for industrial, telecom, medical and defence builds, matched on interface, temperature and package.
- Hard To Find And Obsolete Parts: PHY and switch devices that go on allocation while boards stay in production, sourced with the lifecycle status stated up front.
- Cross Reference Support: Host interface, strap default, management interface and clock differences listed with the quote before a board change is committed.
- Stock And Build Quantities: Prototype quantities, repair quantities and volume orders are all welcome, with the batch information stated per line.
- BOM Kitting: The PHY, the magnetics, the crystal and the connector for the same port can be quoted together.
- Reply With Evidence: Documents, batch marking and the condition of the parts are stated on the quote before the order is placed.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: BOM Shortage Recovery, MCU and Embedded Processors, STM32F103 Mainstream MCUs for Industrial Control Boards, FPGA and Programmable Logic.