Contact Us
  • Home
  • COMPONENTS
  • Battery Chargers and Fuel Gauges for Portable Instruments

Battery Chargers and Fuel Gauges for Portable Instruments

Linear chargers from 500 mA to 1.5 A with power path and input current limit. Switch mode chargers up to 5 A with I2C control and 93 percent efficiency. Fuel gauges using voltage model or coulomb counting, with and without a sense resistor. Protection, termination and status outputs in SOT-23, QFN and SON packages.
quote now

Product Specifications

Product Overview

A portable instrument has three power jobs that are usually three separate parts: charging the cell, deciding how much charge is left, and keeping the system alive while the cell is flat. On a handheld meter the charger is a linear part because the input is a 5 V adapter and the cell is one lithium cell; on a battery pack with a 12 V or 20 V input the charger is a switch mode stage because the dissipation of a linear part at 2 A would need a heatsink that does not fit. The gauge is a separate decision again: a voltage model gauge needs no sense resistor and no learning cycle, a coulomb counting gauge needs a 10 milliohm shunt but holds its accuracy when the load profile is unknown.

The linear group on this page runs from the MCP73831 and TP4056 at 500 mA and 1 A, through the LTC4054, to the BQ24075 and BQ24074, which add power path control so the system stays powered from the adapter while the cell charges and switches over without a glitch when the adapter is removed. The switch mode group starts at the BQ25606 and BQ25895 at 3 A and 5 A with I2C control of the input current limit, the charge current and the termination threshold, which is what a USB-C input needs because the available current is negotiated rather than fixed.

On the gauge side the MAX17048 uses a voltage model and no sense resistor, draws 3 microamps in hibernate and reports state of charge, voltage and rate over I2C, which suits a sealed handheld where a shunt would cost more than the gauge. The BQ27441-G1 uses impedance tracking with a 10 milliohm sense resistor and reports remaining capacity in mAh, state of charge and state of health, which suits a pack that is cycled hard and where the user expects the percentage to hold under load. The BQ34Z100 extends the same approach to multi cell packs and to chemistries other than lithium ion.

Key Specifications

ParameterLinear chargersSwitch mode chargersFuel gauges
Input voltage4.35 V to 6.5 V, 28 V tolerant on the BQ2407x3.9 V to 14 V with input current limit2.5 V to 4.5 V cell supply
Charge current500 mA to 1.5 A2 A to 5 A with I2C settingNot applicable
Cell countOne cellOne cellOne cell, two cells and multi cell packs
TopologyLinear, with power path on the BQ2407xSynchronous buck, 1.5 MHz switchingVoltage model or coulomb counting
AccuracyPlus or minus 0.5 percent voltage regulation on the BQ2407xPlus or minus 0.5 percent voltage and plus or minus 5 percent current regulationReported state of charge with 7.5 mV per cell voltage measurement
TerminationCurrent threshold set by a resistorI2C programmable, with recharge thresholdNot applicable
InterfaceStatus pins, no bus neededI2C for current limit, voltage and statusI2C at 400 kHz, alert output
Quiescent currentTens of microamps in standbyTens of microamps in ship mode3 microamps hibernate, 23 microamps active on the MAX17048
PackageSOT-23, SOP-8 and QFNQFN and WQFNTDFN, SON and WLP

Included Models and Order Codes

The table lists the charger and gauge order codes quoted most often for handheld instruments. State the cell chemistry and capacity, the input source and its current limit, and whether the gauge must work without a sense resistor, and the order code is confirmed with packing.

Part NumberFunctionCharge CurrentInputInterfacePackage
BQ24075RGTRLinear charger with power path and input current limit1.5 AUSB or adapter up to 6.5 VStatus pinsQFN
BQ24074RGTRSame family with adjustable termination and sys output1.5 AUSB or adapter up to 6.5 VStatus pinsQFN
BQ25895RTWRSwitch mode charger with MaxCharge and boost mode5 A3.9 V to 14 VI2CWQFN
BQ25606RGERStandalone switch mode charger for USB input3 A4 V to 13.5 VStatus pinsQFN
TP4056Linear charger, constant current constant voltage1 A4.5 V to 5.5 VStatus pinsSOP-8
MCP73831T-2ACI/OTLinear charger for small cells500 mA3.75 V to 6 VStatus pinSOT-23
LTC4054ES5-4.2#PBFLinear charger with thermal regulation800 mA4.25 V to 6.5 VStatus pinSOT-23
BQ27441DRZR-G1AImpedance tracking fuel gauge with sense resistorNot applicableSingle cellI2CSON
MAX17048G+T10Voltage model fuel gauge without sense resistorNot applicableSingle cellI2CTDFN
BQ34Z100PWR-G1Fuel gauge for multi cell packs and several chemistriesNot applicableUp to 16 series cells with a dividerI2CTSSOP
LTC2944IDD#PBFCoulomb counter with voltage and temperatureNot applicableUp to 60 V railI2CDFN

Key Features

Power path keeps the system alive – on the BQ2407x the system rail is fed from the adapter while the cell charges and from the cell when the adapter is removed, so a meter does not reboot when it is plugged in.

Input current limit that matches the source – the USB input limit is set by a resistor or by I2C, so a 500 mA port is not asked for 1 A and a weak adapter does not collapse the rail.

Thermal regulation instead of shutdown – the linear parts fold the charge current back as the junction heats, which keeps a sealed handheld charging rather than cycling on the thermal trip.

Gauge without a sense resistor – the MAX17048 needs no shunt and no learning cycle, which removes a component and a production step from a low cost instrument.

Gauge with coulomb counting – the BQ27441 holds state of charge under a load profile that a voltage model cannot follow, and reports state of health as the cell ages.

Status and interrupts – charge, done and fault are available as pins or as I2C status bits, so the firmware can show the real state instead of a timer driven guess.

Applications

These parts are quoted for battery powered instruments, typically where: A pack or a handheld board is normally quoted with the SUPERB PCB and SUPERB PCBA work we support for the same product, so the charger, the gauge and the assembly are handled as one order.

Handheld test meters – a single cell, a 5 V USB input and a display that must show a percentage the user trusts after two years of partial cycles.

Portable medical and monitoring devices – power path control so the device keeps running while charging, with termination and fault status available to the host.

Field data loggers and trackers – a solar or 12 V input, a switch mode charger and a gauge that survives a load profile with long sleep periods and short transmit bursts.

Sourcing and Cross-Reference

Charger and gauge orders depend on details that the family name hides: the input voltage rating, whether the part is standalone or I2C controlled, and the packing. The BQ24075 and BQ24074 share a body and a pinout but differ in termination behaviour, and the BQ27441 has several firmware variants under one base part number. We quote the full string and confirm the variant on the confirmation rather than after the reels arrive.

Where a pack is being moved from an older charger, the useful step is to keep the sense resistor and the thermistor network unchanged and change only the controller. That is possible across most of the BQ24xxx and BQ25xxx range and across the MAX1704x gauges, and it keeps the existing production test fixture valid. When the change cannot keep the footprint, we say which pins move and what the test fixture has to check.

Where the boards are assembled in volume, SUPERB Assembly support covers the SMT build of the power and charging section.

Q: Can you supply the charger and the fuel gauge from the same pack BOM in one shipment?

A: Yes. Send the complete order code and the variant letter or suffix, state the cell capacity and the input source, and the SUPERB Tech sales team will confirm availability and the packing.

Why Buyers Source Charging and Gauging Through SUPERB

  1. Variant level quoting: the base part number usually covers several firmware and packing variants; the quote and the delivery note carry the exact one.
  2. Charger and gauge together: both lines of a pack BOM are quoted as one set, so the current limit of the charger and the sense resistor of the gauge are checked against each other before the build.
  3. Evaluation quantities: small quantities for a first prototype and reels for production come from the same source, which keeps the firmware validated on the same silicon as the build.
  4. Documentation for the pack file: date code, lot and country of origin are recorded per reel for the battery pack documentation that shipping and customs ask for.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Power management ICs, LDO linear regulators, Step down DC-DC converters, Component lead time solutions, Logic level shifters and IO expanders.