Contact Us
  • Home
  • COMPONENTS
  • Magnetometer and Compass Sensors for Heading Reference

Magnetometer and Compass Sensors for Heading Reference

Three axis magnetometers from 8 gauss to 50 gauss full scale range Hall, AMR and magneto inductive types with 16 bit to 20 bit output Heading accuracy from 0.5 degree for AMR parts and 18 bit resolution All models on this page are grouped into one part for easy sourcing
quote now

Product Specifications

Product Overview

A compass on a real board measures the earth field plus everything the board has put around it. Speakers, motor magnets, current carrying traces and steel fasteners all add a fixed or load dependent offset that is far larger than the signal the heading calculation needs. That is why the useful comparison between magnetometers is not only the full scale range but the offset stability, the noise level and whether the device has a set and reset function to remove the offset drift.

The parts on this page cover the three sensing technologies used for heading: Hall effect parts that are small and cheap, anisotropic magnetoresistive parts that reach 0.5 degree heading accuracy with 18 bit resolution, and magneto inductive parts used where the local magnetic environment is hostile. The choice usually follows from the magnetic interference on the board, not from the price of the sensor.

All models are grouped into this single product, so a flight controller, a handheld compass or a marine instrument can be quoted with the magnetometer, the accelerometer used for tilt compensation and the interface parts in one line. Tell us the heading accuracy required, the available field window and the mechanical mounting, and the class can be matched to the enclosure.

Key Specifications

ParameterHall And MEMS TypesAMR And Magneto Inductive Types
Sensing principleHall effect and MEMS magnetic elementAnisotropic magnetoresistive bridge, or magneto inductive coil
Full scale range8 gauss to 50 gauss, plus 1300 uT and 1000 uT parts8 gauss for the AMR parts, 800 uT for the inductive parts
Output resolution16 bit18 bit to 20 bit
Noise0.25 uT rms to 2 mG rms depending on the bandwidth setting0.4 mG rms for the AMR parts, 13 nT to 50 nT for the inductive parts
Heading accuracy1 to 3 degrees before calibration0.5 degrees for the AMR parts after tilt compensation
InterfaceI2C, up to 200 Hz output data rateI2C and SPI, up to 1000 Hz for the AMR parts
Set and resetInternal offset correction on the newer partsBuilt in set and reset strap that removes offset drift and restores the film
Temperature range-40 C to 85 C, up to 105 C on the automotive qualified AMR part-40 C to 85 C

Included Models and Order Codes

The table lists the magnetometers and compass sensors most often requested for heading and navigation boards. Send the exact order code and the quantity and we confirm availability, the date code and the nearest part with the same footprint.

ModelPrincipleFull ScaleResolution / NoiseInterfacePackage / Notes
HMC5883LMagnetoresistive compass8 gauss12 bit, heading accuracy 1 to 2 degreesI2C3 x 3 x 0.9 mm package, no longer recommended for new designs
QMC5883LHall effect2 gauss and 8 gauss selectable16 bit, output data rate up to 200 HzI2CLGA, 3 x 3 x 0.9 mm
LIS3MDLHall effect4, 8, 12 and 16 gauss selectable16 bit, up to 155 HzI2C and SPILGA-12, 2 x 2 x 1 mm
LIS2MDLHall effect50 gauss16 bit, low power continuous modeI2C and SPILGA-12
LSM303AGRHall effect with accelerometer50 gauss16 bit magnetic plus 16 bit accelerometerI2C and SPILGA-12, tilt compensation on one die
MMC5603NJAMR30 gauss20 bit, 0.0625 mG per LSB, 2 mG rms noise, heading 1 degreeI2C and I3CWafer level package 0.8 x 0.8 x 0.4 mm
MMC5983MAAMR8 gauss18 bit, 0.4 mG rms noise, heading accuracy 0.5 degreeI2C and SPILGA-16, 3 x 3 x 1 mm, AEC-Q100 qualified, -40 C to 105 C
BMM150FlipCore Hall1300 uT on X and Y, 2500 uT on ZResolution 0.3 uT, heading accuracy 2.5 degreesI2C and SPI, 3 wire and 4 wireWLCSP-12, 1.56 x 1.56 x 0.6 mm
MAG3110MEMS magnetic sensor1000 uT16 bit, sensitivity 0.1 uT per LSB, noise 0.25 uT rmsI2C up to 400 kHz10 pin DFN, 2 x 2 x 0.85 mm, output rate up to 80 Hz
RM3100Magneto inductive800 uTSensitivity 13 nT to 50 nT depending on cycle count, noise 15 nT to 30 nTSPI and I2CMagI2C interface chip 4.0 x 4.0 x 0.75 mm plus sensor coils, immune to local stray fields
AK8963Hall effect4912 uT14 bit and 16 bit output modesI2CUsed alongside the MPU-9250 inertial part on navigation boards
MMC5983MA-AMR moduleAMR8 gaussSame die as MMC5983MA with coils and support partsI2C and SPIModule form for retrofit onto boards with existing ground planes

Key Features

Full Scale Chosen Against The Board – 50 gauss parts survive close to speakers and motor magnets, while 8 gauss AMR parts give the best resolution where the magnetic environment is quiet.

Set And Reset For Offset Drift – The AMR parts carry an internal strap that removes the offset change with temperature and clears residual magnetisation after the board has been exposed to a strong field.

0.5 Degree Heading Accuracy – 18 bit AMR output with 0.4 mG rms noise supports heading accuracy that a Hall part cannot reach, which matters for survey and marine instruments.

Low Noise For Heading Stability – Noise in milligauss or nanotesla, quoted at a defined bandwidth, because a quiet output is what keeps the heading steady when the vehicle vibrates.

Tilt Compensation Parts – Combined magnetometer and accelerometer devices keep the two sensing axes aligned on one die, which removes the mounting error of two separate packages.

Immune To Local Interference – Magneto inductive types tolerate nearby current paths and ferrous hardware better than Hall or AMR parts, at the cost of a larger sensor footprint.

Second Sources In The Same Footprint – Where the original compass is obsolete, the nearest pin compatible part is quoted with the register map and range differences stated.

Applications

Boards where these sensors are specified: Heading boards are quoted as one item covering the magnetometer, the accelerometer used for tilt and the SUPERB PCB and SUPERB PCBA work we support for the same board.

Flight Controllers And Heading Hold – Multirotor and fixed wing boards that need a stable yaw reference next to motors and current carrying wiring.

Electronic Compasses And Marine Instruments – Handheld compasses, binoculars and marine displays where 0.5 to 1 degree heading accuracy is part of the product specification.

Antenna And Rotator Positioning – Pointing systems that use magnetic heading to initialise the direction of a rotator or a tracking antenna.

Robotics And AGV Navigation – Mobile platforms that fuse magnetic heading with wheel odometry and inertial data where the floor environment is known.

Sourcing and Cross-Reference

Compass parts are frequently discontinued because the consumer market moves to the next phone generation, and the parts that survive are the ones with industrial and automotive qualifications. Two of the common choices on this page are already in that position, so boards designed around them need a substitute that fits the footprint, the supply voltage and the register map.

We compare candidates on full scale, resolution, noise at the bandwidth used, interface voltage and the calibration method the host firmware expects. Where the substitute needs different coefficients, a different set and reset routine or a new mounting orientation, that is stated with the quote rather than found during board bring up.

Where the board goes into volume, SUPERB Assembly support covers the SMT build of the sensor section.

Q: Can you supply an alternative for a discontinued magnetometer part number?

A: Yes. Send the part number and the quantity and the SUPERB Tech sales team will confirm availability and a pin compatible alternative where one exists.

Why Source Compass Sensors from Superb Automation?

  1. Specialised Sourcing Focus: Sensors, RF parts and mixed signal devices for industrial, telecom, medical and defence builds, compared on the datasheet figures the application depends on.
  2. Hard To Find And Obsolete Parts: Compass and magnetometer parts that leave production while platforms stay in service, sourced with the vendor status and the nearest equivalent stated up front.
  3. Cross Reference Support: Full scale, noise, interface voltage and register map differences listed with the quote so the substitute can be signed off before production.
  4. Stock And Build Quantities: Prototype quantities, repair quantities and volume orders are all welcome, with batch information stated per line.
  5. BOM Kitting: The magnetometer, the accelerometer and the interface parts for the same board can be quoted together.
  6. Reply With Evidence: Documents, batch marking and the condition of the parts are stated on the quote before the order is placed.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Obsolete RF Part Replacement, Sensors and Detectors, 6-Axis IMU Sensors for Flight Control and Navigation, BOM Shortage Recovery.