Gate Driver Chips for Motor and Power Stage Control
Product Specifications
Product Overview
A power stage is only as fast as the driver in front of it. The gate driver has to shift the control signal up to the high side rail, deliver enough peak current to charge the gate in tens of nanoseconds, and keep the high side and low side from conducting at the same time. When a motor board stops working after a driver change, the cause is usually one of three things: too little peak current for the gate charge, a missing dead time that lets both switches conduct, or a bootstrap supply that cannot hold the high side above the UVLO threshold at the switching frequency in use.
The families on this page cover both halves of that problem. The high voltage parts handle the level shift and the dead time internally, so a motor drive or inverter can be built with a small external bootstrap diode and capacitor. The low side and isolated parts are used where the gate is driven from a separate supply, where a wide common mode range has to be tolerated, or where the power stage sits on a mains referenced rail and isolation is required by the safety case.
All models are grouped into this single product, so one enquiry can cover a three phase board with a high and low side bridge, its gate resistors and its bootstrap network instead of several sourcing rounds. Tell us the gate charge, the switching frequency, the bus voltage and the ambient temperature, and the driver class can be matched to the stage instead of the other way round.
Key Specifications
| Parameter | High And Low Side Drivers | Low Side and Half Bridge Drivers |
|---|---|---|
| Channel configuration | High side and low side in one package, independent or half bridge | Single low side, dual low side, or isolated dual channel |
| Voltage class | 500 V and 600 V high side offset | Up to 100 V to 120 V half bridge, low side any rail |
| Output current (source / sink) | 2 A and 2.5 A class | 1 A, 1.5 A and 4 A classes |
| Logic supply | 10 V to 20 V VCC, inputs compatible with 3.3 V logic | 4.5 V to 18 V VDD for low side, separate isolated supply for isolated drivers |
| Propagation delay | 120 ns turn on, 94 ns turn off (typical) | 13 ns to 30 ns typical, delay matching within 5 ns |
| Dead time | Internally fixed at 520 ns, or programmable on the larger parts | Fixed internal dead time, or set by the controller |
| Protection | Under voltage lockout, cycle by cycle shutdown, latch immune construction | Under voltage lockout, negative voltage tolerance, some with de saturation detection |
| Temperature range | -40 C to 125 C junction | -40 C to 125 C junction |
Included Models and Order Codes
The table lists the driver classes most often requested for motor and power stage boards. Send the complete order code including the package letter and the temperature suffix and we confirm availability against that exact string.
| Model | Channels and Type | Voltage Class | Peak Output | Package | Notes |
|---|---|---|---|---|---|
| IR2110PBF | High side and low side, one package | 500 V offset | 2 A / 2 A, 120 ns / 94 ns | 14 lead PDIP | Bootstrap operation, shutdown pin, 10 V to 20 V VCC |
| IR2110SPBF | High side and low side, one package | 500 V offset | 2 A / 2 A | 16 lead SOIC wide body | Same die as IR2110 in surface mount |
| IR2110STRPBF | High side and low side, one package | 500 V offset | 2 A / 2 A | 16 lead SOIC wide body, tape and reel | Volume packaging of the SOIC version |
| IR2113PBF | High side and low side, one package | 600 V offset | 2 A / 2 A | 14 lead PDIP | Higher offset rating for 400 V class buses |
| IR2113STRPBF | High side and low side, one package | 600 V offset | 2 A / 2 A | 16 lead SOIC wide body, tape and reel | Delay matching 20 ns maximum |
| IR2104PBF | Half bridge with internal dead time | 600 V offset | 210 mA / 360 mA | 8 lead PDIP | 520 ns typical dead time, 10 V to 20 V VCC, single input |
| IR2104SPBF | Half bridge with internal dead time | 600 V offset | 210 mA / 360 mA | 8 lead SOIC | For low gate charge MOSFETs and small motor boards |
| IR21844SPBF | Half bridge with programmable dead time | 600 V offset | 1.9 A / 2.3 A | 14 lead SOIC | Dead time set by an external resistor |
| IR2136PBF | Three phase bridge, six outputs | 600 V offset | 200 mA / 350 mA | 28 lead SOIC wide body | Matched channels for brushless motor commutation |
| UCC27517DBVR | Single channel, low side | Low side, any rail | 4 A / 4 A | SOT-23-5 | 4.5 V to 18 V VDD, 13 ns typical propagation delay |
| UCC27517AQDBVRQ1 | Single channel, low side, automotive | Low side, any rail | 4 A / 4 A | SOT-23-5 | AEC-Q100 qualified for engine bay and motor control |
| UCC27211D | Half bridge, high and low side | 120 V offset | 4 A / 4 A | 8 lead SOIC | Fast switching with negative voltage tolerance |
| TC4427AEPA | Dual channel, low side | Low side, any rail | 1.5 A per channel | 8 lead PDIP | Non inverting, 4.5 V to 18 V VDD |
| TC4427ACOA | Dual channel, low side | Low side, any rail | 1.5 A per channel | 8 lead SOIC | Latch proof construction for inductive loads |
| MIC4427YM | Dual channel, low side | Low side, any rail | 1.5 A per channel | 8 lead SOIC | Pin compatible dual driver, wide supply range |
| LM5109BMA | Half bridge, high and low side | 100 V offset | 1 A / 1 A | 8 lead SOIC | Small motor and half bridge stage option |
| UCC21520DW | Dual channel, isolated | 5.7 kV isolation, any rail | 4 A / 6 A | 16 lead SOIC wide body | For high side rails that need a galvanic barrier |
Key Features
High Side Without A Transformer – Level shift and bootstrap parts let an N channel MOSFET sit on a 500 V or 600 V rail, so a three phase stage needs no isolated gate supply.
Peak Current Matched To Gate Charge – 2 A, 2.5 A and 4 A peak output classes, chosen against the gate charge and the target rise time rather than picked from a price list.
Dead Time That Actually Protects – 520 ns internal dead time on the half bridge parts, programmable on the larger ones, so shoot through current does not come back as a failed stage.
Delay Matching For Parallel Stages – Matched propagation delay keeps the phases of a three phase bridge aligned, which matters as soon as the switching frequency goes up.
Under Voltage Lockout And Shutdown – Both the floating supply and the logic supply are monitored, and the cycle by cycle shutdown pin allows a fault signal to stop the stage inside one switching period.
Waveforms For Any Process – 500 V and 600 V parts for 400 V class buses, 100 V and 120 V parts for battery and low voltage motor stages, low side parts where a dedicated supply already exists.
Pin Compatible Second Sources – Where a driver is obsolete or on allocation, the nearest pin compatible device in the same package is quoted alongside it, with the differences in timing stated.
Applications
Boards where these drivers are specified: A gate driver is normally quoted together with the SUPERB PCB and SUPERB PCBA work we support for the same power board, so the stage arrives as one line on the purchase order.
Brushless And PMSM Motor Drives – Three phase stages in pumps, fans, compressors and power tools where the six gate signals come from one controller and the bus runs at 300 V to 400 V.
Induction Cooking And PFC Stages – Half bridge resonant stages where the dead time and the high side bootstrap supply determine whether the switches survive the first overcurrent event.
Inverters For Telecom And Industrial Power – Sine wave inverters and UPS output stages that need a documented driver with a defined UVLO window rather than a discrete level shift circuit.
Battery And Low Voltage Motor Control – 24 V and 48 V motor boards built on half bridge or dual low side drivers where 4 A peak drive shortens the switching edge.
Sourcing and Cross-Reference
Gate drivers are a common line to disappear without a last time buy notice, and the substitutes are rarely drop in. Pin count, input logic polarity, dead time and UVLO thresholds all differ between families, and a driver that looks equivalent on the front page table can invert the input logic. We state which of those differ before the parts are ordered.
For obsolete drivers we check the original part against the current family from the same vendor first, then look at the wider market. Where the package is SOIC or PDIP and the pin out is published as compatible, the cross reference is supplied with the quote. Where the substitute needs an input inverter or an added shutdown network, that is stated rather than left to be discovered on the line.
Where the power board is built in volume, SUPERB Assembly support covers the SMT build of the stage.
Q: Can you supply pin compatible replacements for discontinued gate driver part numbers?
A: Yes. Send the order code, the package and the quantity and the SUPERB Tech sales team will reply with availability and the pin compatible option in the same package.
Why Source Gate Drivers from Superb Automation?
- Specialised Sourcing Focus: Power, RF, sensor and mixed signal parts for industrial, telecom, medical and defence builds, quoted by engineers who read the datasheet tables.
- Hard To Find And Obsolete Parts: Drivers that go end of life while the platform stays in service, sourced with the last time buy position or the nearest equivalent stated up front.
- Cross Reference Support: Input polarity, dead time, UVLO window and package differences listed with the quote so the substitute can be signed off before it reaches production.
- Stock And Build Quantities: Samples for the first prototype, repair quantities and volume orders are all welcome, and the batch information is stated per line.
- BOM Kitting: Drivers, gate resistors, bootstrap diodes and the power switches for the same stage can be quoted together, which removes a layer of incoming inspection.
- Reply With Evidence: Documents, batch marking and the condition of the parts are stated on the quote before the order is placed.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Obsolete RF Part Replacement, Power Management ICs, Discrete and Power Semiconductors, Step-Down DC-DC Converter Chips for Industrial Power Rails.