16-Bit SAR ADCs for Instrumentation and Control
Product Specifications
Product Overview
The choice on a 16 bit channel is usually between sampling every input at the same instant and scanning the inputs through a multiplexer. Both are successive approximation converters: the difference is what happens in front of the converter. A simultaneous part carries one track and hold and one converter per channel, so the phase between a motor phase current and the bus current, or between a voltage and the current that produced it, is fixed by the conversion start and not by the scan order. A multiplexed part carries a single converter and switches the inputs into it, which is smaller and cheaper per channel but leaves a time skew between channels.
The AD7606 family is the reference point for the first group. It converts eight, six or four channels at 200 kSPS each, accepts true bipolar plus and minus 10 V or plus and minus 5 V directly, holds a 1 MOhm input impedance that does not fall with sample rate, and tolerates plus or minus 16.5 V at the pin. The second order filter in front of the converter has a 22 kHz corner and gives 40 dB of rejection at the 200 kSPS Nyquist, so an anti alias network is already inside the package. The same footprint carries the AD7606B at 800 kSPS and the AD7606C-16 at 1 MSPS, which matters when a channel count is fixed but the loop bandwidth has to grow.
The second group is the multiplexed and single channel range. The ADS8688 scans eight channels at 500 kSPS aggregate with plus and minus 10.24 V, plus and minus 5.12 V and plus and minus 2.56 V ranges selectable per channel, a 4.096 V reference and protection to plus or minus 20 V, which suits a 4 to 20 mA card with no external front end. The AD7689 and AD7699 put eight channels, a sequencer and a reference in a 4 mm package. At the low end of the count, the AD7980, AD7688 and LTC2378-16 give one channel at 500 kSPS to 1 MSPS with a fraction of the power, which is what a battery instrument or a multi card rack usually needs.
Key Specifications
| Parameter | Simultaneous sampling | Multiplexed and single channel |
|---|---|---|
| Resolution | 16 bit, no missing codes | 16 bit, no missing codes |
| Throughput | 200 kSPS to 1 MSPS on every channel | 250 kSPS to 1 MSPS aggregate |
| Channel count | 4, 6 or 8 sampled at the same instant, 16 channel parts in two groups of eight | 1 to 8 channels through an input multiplexer |
| Input range | True bipolar plus and minus 10 V and plus and minus 5 V, 1 MOhm input impedance | 0 V to VREF unipolar, or true differential up to plus and minus VREF |
| Overvoltage | Clamp protection to plus or minus 16.5 V on the AD7606, plus or minus 20 V on the ADS8688 | Set by the external driver stage, protect the pin with a series resistor |
| Reference | On chip 2.5 V reference and buffer | On chip 4.096 V reference on the data acquisition parts, external on the AD7980 |
| Linearity and noise | Plus or minus 0.5 LSB INL and 95.5 dB SNR typical on the AD7606 | Plus or minus 0.4 LSB INL typical and 95.5 dB SNR at 20 kHz on the AD7688 |
| Supply | Single 5 V analog with a 2.3 V to 5 V digital supply | 5 V analog with a separate 1.8 V to 5 V logic supply |
| Package | 64 lead LQFP | 10 lead MSOP, LFCSP and TSSOP |
Included Models and Order Codes
The table lists the converter order codes most often requested for control and measurement cards. Send the full order code with the temperature grade and package letter, the number of channels that must be sampled together, and the input range the sensor delivers, and availability is confirmed against that string rather than the series name.
| Part Number | Channels | Throughput | Input Range | Interface | Package |
|---|---|---|---|---|---|
| AD7606BSTZ | 8 simultaneous | 200 kSPS | Plus or minus 10 V, plus or minus 5 V | Parallel and SPI | LQFP |
| AD7606-6BSTZ | 6 simultaneous | 200 kSPS | Plus or minus 10 V, plus or minus 5 V | Parallel and SPI | LQFP |
| AD7606-4BSTZ | 4 simultaneous | 200 kSPS | Plus or minus 10 V, plus or minus 5 V | Parallel and SPI | LQFP |
| AD7606BBSTZ | 8 simultaneous | 800 kSPS | Plus or minus 10 V, plus or minus 5 V | Parallel and serial | LQFP |
| AD7606C-16BSTZ | 8 simultaneous | 1 MSPS | Plus or minus 10 V, plus or minus 5 V | Serial | LQFP |
| AD7616BSTZ | 16 in two simultaneous groups | 1 MSPS | Plus or minus 10 V, plus or minus 5 V | Parallel and serial | LQFP |
| ADS8588SIPM | 8 simultaneous | 500 kSPS | Plus or minus 10 V, plus or minus 5 V | Parallel and serial | LQFP |
| ADS8688IDBTR | 8 multiplexed | 500 kSPS | Plus or minus 10.24 V, plus or minus 5.12 V, plus or minus 2.56 V | SPI | TSSOP |
| ADS8684IDBTR | 4 multiplexed | 500 kSPS | Plus or minus 10.24 V, plus or minus 5.12 V, plus or minus 2.56 V | SPI | TSSOP |
| AD7689BCPZ | 8 multiplexed | 250 kSPS | 0 V to 4.096 V, internal reference | SPI | LFCSP |
| AD7699BCPZ | 8 multiplexed | 500 kSPS | 0 V to 4.096 V, internal reference | SPI | LFCSP |
| AD7980ARMZ | 1 | 1 MSPS | 0 V to VREF, external reference | SPI | MSOP |
| AD7688BRMZ | 1 differential | 500 kSPS | 0 V to VREF, true differential | SPI | MSOP |
| LTC2378CDE-16 | 1 differential | 1 MSPS | 0 V to VREF, external reference | SPI | DFN |
Key Features
Simultaneous sampling – every channel is captured on the same conversion start, so the phase between two currents or between a voltage and its current stays fixed from sample to sample.
Direct plus or minus 10 V input – series resistors, clamps and the bipolar scaling are inside the part, so a 10 V transducer or a 4 to 20 mA loop resistor connects without an external bipolar driver stage.
Constant 1 MOhm input impedance – the input resistance does not fall as the sample rate rises, which keeps gain error stable when the scan rate is changed at run time.
On chip antialiasing – the second order filter on the simultaneous parts has a 22 kHz corner and gives 40 dB of rejection at the 200 kSPS Nyquist, so the external network only has to handle the residue.
Oversampling and averaging – the digital filter inside the part trades throughput for resolution without extra firmware, which is useful on slow pressure and temperature bridges.
SPI with daisy chain – several converters can share one chip select and one data line, which keeps the digital side small on boards where the isolation barrier is the cost driver.
Applications
These converters sit on the analog edge of control and measurement cards, in builds where: The converters for a control card are normally quoted together with the SUPERB PCB and SUPERB PCBA work we support for that same card, so the analogue front end, the protection around it and the assembly arrive as one order.
Servo and motor drives – phase currents are captured at the same instant and the conversion is started by the PWM timer, so the current loop sees a true snapshot rather than three samples spread over the period.
Protection relays and power quality – eight voltage and current channels on one part, with the plus or minus 10 V range covering instrument transformers and the on chip filter removing the switching residue.
Test and medical instruments – multiplexed 16 bit SAR where the rate per channel is modest but linearity and missing codes are not negotiable, as on scanner front ends and patient monitor auxiliary channels.
Sourcing and Cross-Reference
Two things decide whether a converter order goes through cleanly: the exact order code, and whether the package and temperature grade on the BOM match what the line can accept. The same family name covers LQFP and TSSOP bodies, commercial and industrial grades, and reel or tray packing, and a substitution made on the family name alone is where assembly problems start. We quote against the full string and state the date code and packing on the confirmation.
On allocation, the practical route is the nearest part that keeps the pinout and the interface. The AD7606, AD7606B and AD7606C-16 share a footprint, so a board built for 200 kSPS can move up without a layout change; the ADS8688 and ADS8684 differ only in channel count. Where a part has no drop in option, we say so and quote the lead time instead of offering a different family that would need a new front end.
Where the cards are built in volume, SUPERB Assembly support covers the SMT build of the analogue and digital sections.
Q: Can you supply pin to pin replacements when the exact ADC order code is on allocation?
A: Yes. Send the complete order code with the temperature grade and package letter, state the number of channels that must be sampled together, and the SUPERB Tech sales team will confirm availability and the nearest part that keeps the pinout.
Why Buyers Source 16-Bit Converters Through SUPERB
- Full order code: quotations are made against the complete string including grade, package and packing, so what arrives matches the BOM line rather than the family.
- Cross reference with the differences written out: when a drop in part exists we list the pin and software differences; when it does not, we say that instead of proposing a board change.
- One shipment for the analog section: converters, references, drivers and the protection parts around them can be consolidated, which removes the split delivery that usually delays a first build.
- Traceability per reel: date code and lot are recorded against the delivery note, so incoming inspection and any later failure analysis can be tied back to the batch.
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Analog and mixed signal ICs, Precision operational amplifiers, DACs and voltage references, Pin to pin cross reference, Obsolete part cross reference.