RS-485 and RS-232 Transceiver Chips for Industrial Interfaces
Product Specifications
Product Overview
A serial interface part is usually specified by the standard, not by the datasheet, and that is where the trouble starts. RS-485 designs differ in data rate, unit load, common mode range and whether the driver needs an enable pin at all, while RS-232 designs differ in the number of drivers and receivers and in the supply the charge pump has to work from. Two parts with the same function and the same pinout can be a 250 kbps slew limited device and a 26 Mbps device.
This page groups the interface transceivers we supply along those lines. The RS-485 and RS-422 parts cover 3.3 V and 5 V operation, half duplex and full duplex, data rates from 250 kbps to 26 Mbps, common mode ranges of -7 V to +12 V, unit loads down to one eighth so up to 256 nodes can share the bus, and bus pin ESD protection above 15 kV HBM. The auto direction parts remove the driver enable control completely, which is what most two wire field buses want.
Where the bus has to cross an isolation barrier the isolated parts integrate the iCoupler isolation and, in the wider devices, the isolated DC to DC conversion that powers the field side, so a single 3.3 V or 5 V rail on the logic side is enough. For the service port, the RS-232 line drivers and receivers work from 3 V to 5.5 V with an integrated dual charge pump, two drivers and two receivers for the standard five capacitor layout, 250 kbit per second data rate and 15 kV ESD on the line pins. The digital isolation parts used around these interfaces are listed on our isolator page.
Key Specifications
| Parameter | RS-485 and RS-422 | RS-232 | Isolated RS-485 |
|---|---|---|---|
| Data rate | 250 kbps, 2.5 Mbps, 10 Mbps, 16 Mbps and 26 Mbps versions | 250 kbit per second, up to 1 Mbps in the high speed option | 500 kbps and 16 Mbps versions |
| Duplex | Half duplex and full duplex | Point to point, two drivers and two receivers typical | Half duplex and full duplex |
| Supply | 3.3 V and 5 V single supply | 3 V to 5.5 V with integrated charge pump | Single 3.3 V or 5 V rail on the logic side |
| Bus loading | From 1 unit load down to 1/8 unit load, up to 256 nodes | Not applicable | 1/4 unit load on the isolated receiver input |
| Common mode range | -7 V to +12 V | Not applicable | -7 V to +12 V |
| ESD on bus pins | Above 15 kV HBM, 15 kV on the protected parts | 15 kV HBM on line terminals | 15 kV ESD on the bus pins |
| Isolation | Not applicable | Not applicable | 2500 V rms to 5000 V rms depending on the body |
| Fail safe | Bus idle, open and short circuit fail safe on the newer parts | Not applicable | Bus idle and open circuit fail safe |
Included Models and Order Codes
The table lists the interface part codes most often requested for industrial, telecom and instrument boards. Send the complete order code including the temperature grade and we confirm availability against that string.
| Part Number | Function | Data Rate | Supply | Package | Notes |
|---|---|---|---|---|---|
| MAX485 | RS-485 and RS-422, half duplex, one driver and one receiver | Industry standard slew limited part | 5 V | DIP-8, SOIC-8 | Classic 75176 pinout, low power, current limited driver output |
| MAX3485 | RS-485 and RS-422, half duplex | 10 Mbps | 3.3 V | SOIC-8 | 8 ns maximum skew, 2 nA shutdown, up to 32 transceivers on the bus |
| MAX3483 | RS-485 and RS-422, half duplex, slew rate limited | 250 kbps | 3.3 V | SOIC-8 | Reduced EMI and reflections, error free data on unterminated cable |
| MAX3486 | RS-485 and RS-422, half duplex, partially slew limited | 2.5 Mbps | 3.3 V | SOIC-8 | Middle speed option of the same family |
| MAX3488 | RS-485 and RS-422, full duplex, slew rate limited | 250 kbps | 3.3 V | SOIC-8 | Full duplex pair of the 3483 |
| MAX3490 | RS-485 and RS-422, full duplex | 10 Mbps | 3.3 V | SOIC-8 | Full duplex at 10 Mbps |
| MAX3491 | RS-485 and RS-422, full duplex with enable pins | 10 Mbps | 3.3 V | SOIC-8 | Driver and receiver enable for shared buses |
| MAX13487E | RS-485, half duplex with auto direction | 500 kbps | 5 V | SOIC-8 | Auto direction control, 1/4 unit load up to 128 transceivers, 15 kV ESD, hot swap |
| MAX13488E | RS-485, half duplex with auto direction | 16 Mbps | 5 V | SOIC-8 | 80 ns maximum receiver propagation delay, same auto direction feature |
| SN65HVD30 | RS-485, full duplex | 26 Mbps | 3.3 V | SOIC-8 | 1/8 unit load up to 256 nodes, 15 kV HBM bus pin ESD, 1 uA standby |
| SN65HVD31 | RS-485, full duplex | 5 Mbps | 3.3 V | SOIC-8 | Slower version with the same pinout and fail safe behaviour |
| SN65HVD32 | RS-485, full duplex | 1 Mbps | 3.3 V | SOIC-8 | Long cable option, -40 C to +85 C |
| SN65HVD33 | RS-485, full duplex with enable pins | 26 Mbps | 3.3 V | SOIC-8 | Active high driver enable and active low receiver enable |
| ADM2483 | Isolated RS-485, half duplex | 500 kbps | 3.3 V or 5 V | SOIC-16 wide body | Slew limited isolated transceiver with iCoupler isolation |
| ADM2582E | Isolated RS-485 with integrated isolated DC to DC | 16 Mbps | 5 V | SOIC-20 wide body | 15 kV ESD on bus pins, no external isolated supply needed |
| ADM2587E | Isolated RS-485 with integrated isolated DC to DC | 500 kbps | 5 V | SOIC-20 wide body | Slower member of the isolated family for long field buses |
| MAX3232 | RS-232 line driver and receiver, two drivers and two receivers | 250 kbit per second | 3 V to 5.5 V | SOIC-16 | Four 0.1 uF capacitors, 300 uA typical supply current, 15 kV ESD |
| MAX3237 | RS-232 with five drivers and three receivers | 250 kbit per second, 1 Mbps in the high speed mode | 3 V to 5.5 V | SOIC-28 or SSOP-28 | Auto shutdown and extra always on outputs for monitoring |
| MAX3222 | RS-232 line driver and receiver | 120 kbit per second guaranteed | 3 V to 5.5 V | SOIC-16 | Low power shutdown option of the same platform |
Key Features
Data rate quoted with the part number – 250 kbps, 2.5 Mbps, 10 Mbps, 16 Mbps and 26 Mbps versions are listed separately because the slew rate changes with the speed grade
Unit load stated for bus planning – from 1 unit load down to 1/8 unit load, which sets whether 32, 128 or 256 nodes can share the cable
Auto direction parts for two wire buses – no driver enable pin and no software direction control, with hot swap protection against false transitions at power up
Isolated options with on board DC to DC – the wider bodies integrate the isolated supply so the field side does not need a second rail
ESD ratings on the bus pins – 15 kV HBM and 15 kV contact ratings are stated per part because the field connector is where the transient arrives
Charge pump RS-232 from a single rail – 3 V to 5.5 V operation with four external capacitors removes the need for plus and minus 12 V supplies
Applications
The parts are supplied for the boards below. An interface section is normally quoted with the SUPERB PCB and SUPERB PCBA work we support for the same board, so the transceivers, the isolation parts and the protection components come from one source.
Industrial field buses – RS-485 multi drop networks for motion controllers, meters and remote IO, including isolated segments between cabinets
Telecom and instrument service ports – RS-232 console and provisioning interfaces on line cards and instruments, from a single 3.3 V or 5 V rail
Motor drives and power stages – isolated serial links between a controller and a power stage where the ground difference and the switching noise have to be kept apart
Sourcing and Cross-Reference
The classic interface parts are exactly the ones that run out. A board qualified on a 5 V 10 Mbps RS-485 part cannot take a 3.3 V 250 kbps part without changing the bus timing, and an isolated part cannot be replaced by a non isolated one without redrawing the barrier.
We confirm availability against the complete order code including speed grade, unit load and temperature range, and where a code is short we quote the nearest option with the data rate, unit load and isolation difference stated so the bus can be rechecked before the order is placed. Long lead time quantities can be scheduled against a production date.
For volume builds, SUPERB Assembly support covers the SMT assembly of the interface board.
Q: Do you have equivalents for the MAX485 and the 3.3 V versions with the same pinout?
A: Yes. Send the order code, the speed grade and the unit load you need and the SUPERB Tech sales team will reply with availability and the nearest option in the same pinout.
Why Buy From Us
- Speed grade and unit load confirmed: the quoted part is checked against the data rate and the bus loading the network was calculated with, not just the function
- Isolated and non isolated kept apart: isolation rating and body are named so a barrier is not crossed by accident during a substitution
- ESD rating documented: bus pin ESD ratings are given per order code because the field connector sees the transient
- Interface and isolation quoted together: transceivers, isolators and the protection components can be sourced as one line so the interface section is complete
Related Product Families
This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Multi-Function ICs, CAN Bus Transceivers and Controllers, DDR3L and DDR4 SDRAM Chips, BOM Shortage Recovery.