Contact Us
  • Home
  • COMPONENTS
  • SFP and SFP+ Digital Diagnostics Controllers for Optical Transceivers

SFP and SFP+ Digital Diagnostics Controllers for Optical Transceivers

Digital diagnostics and control ICs for SFP, SFP+, video SFP and PON modules APC loops with temperature look up tables, SFF-8472 monitoring and maskable laser shutdown All models listed below are combined into this single product for easy sourcing Samples, build quantities, alternatives and cross reference are supported
quote now

Product Specifications

Product Overview

Every pluggable module carries a diagnostics layer that the host reads over a two wire interface: temperature, supply voltage, bias current, transmit power and received power, with alarm and warning flags for each channel and a laser shutdown path that has to work without the host doing anything. That layer is what makes a module compliant with the SFF-8472 memory map, and it is built around a controller rather than a microcontroller in most designs, because the timing, the calibration storage and the safety comparators all have to be present in hardware.

The parts on this page cover the three variants of that job. The DS1874 and DS1873 are single transmitter SFP and SFP+ controllers with complete SFF-8472 control and monitoring, an APC loop and temperature look up tables that compensate tracking error in the laser, six analog monitor channels and maskable laser shutdown. The DS1876 is the dual transmitter version built for video SFP modules, with four 10-bit outputs and separate address spaces for the two transmitters so the host sees two modules in one housing.

For access networks the burst mode problem is different: the transmitter turns on for a few hundred nanoseconds and has to reach the correct bias immediately, and the network expects a calibrated power level. The DS1863 handles BPON, GPON and GEPON burst timing with an APC loop that compensates tracking error and can be set to 0 dB, minus 3 dB or minus 6 dB power levelling without further calibration.

Where a module only needs the resistor and monitoring functions, the DS1859 and DS1856 provide two nonvolatile temperature controlled variable resistors with three analog monitor inputs and a direct-to-digital temperature sensor, with the DS1856 keeping a DS1852 compatible memory map so an existing firmware image does not have to change. These are the parts that a long life industrial or defence module is most likely to be short of, so send the model list and we will confirm availability and the exact revision.

Electrical Specifications

ParameterSFP and SFP+ controllers (DS1873, DS1874)Dual transmitter controller (DS1876)PON burst mode controller (DS1863)Temperature controlled resistors (DS1859, DS1856)
Standards coverageAll SFF-8472 control and monitoring requirements for SFF, SFP and SFP+ modulesSFF-8472 transmitter control and monitoring with a memory map based on SFF-8472BPON, GPON and GEPON burst mode timing requirements for the transmitter and the receiver biasSFF-8472 compatible monitoring channels and identification memory
Monitor channelsSix: temperature, VCC and MON1 to MON4, calibrated internally or externally, with MON3 differential and common mode referred to VCC on the DS1874Six: temperature, VCC, PMON1, BMON1, PMON2 and BMON2, with six quick trips for fast laser safety monitoringFive: temperature, VCC and MON1 to MON3, with internal fast comparators on the laser safety pathFive: temperature, VCC and MON1 to MON3
Temperature sensingInternal direct-to-digital sensor, alarm and warning flags on every monitored channelInternal direct-to-digital sensor, alarm and warning flags on every monitored channelInternal direct-to-digital sensor, alarm and warning flags on every monitored channelInternal direct-to-digital sensor, alarm and warning flags on every monitored channel
Bias and modulation controlAPC loop plus temperature look up table for bias, modulation controlled by a temperature look up table, with tracking error compensationAPC and modulation control for two laser drivers, monitored for high output current, high bias current and low or high transmit powerAPC loop with tracking error compensation as the bias reference, modulation from a temperature indexed look up table, and 0 dB, minus 3 dB or minus 6 dB power levellingTwo temperature controlled variable resistors with 256 positions, nonvolatile settings that change every 2 degrees C, used to set and compensate bias and control voltages
Control outputsDS1874: two 9-bit delta-sigma outputs with 36 entry temperature look up tables. DS1873: four 10-bit delta-sigma outputs with 36 entry tables plus two DACs with 72 entry and 36 entry tablesFour 10-bit delta-sigma outputs, each driven by a 72 entry temperature look up tableTwo digital to analog outputs with temperature indexed look up tablesTwo 50 kohm or two 20 kohm linear variable resistors, 256 positions each
Laser safetyComprehensive fault measurement system with maskable laser shutdown, working without external comparatorsFault measurement with maskable laser shutdown and six quick trips on critical functionsMaskable laser shutdown driven by internal fast comparators for high output, high bias and out of range transmit powerAlarm and warning flags only, shutdown handled by the controller in the design
InterfaceTwo wire compatible interface, with a three wire master on the DS1874 to talk to a laser driver and limiting amplifierTwo wire compatible interface, transmitter 1 at address A2h and transmitter 2 at address B2hTwo wire compatible interface for calibration and monitoringTwo wire serial interface, with two buffers with TTL or CMOS compatible inputs and open drain outputs
Protected memory256 additional bytes at the A0h slave address, with a two level password scheme giving three levels of protection256 additional bytes at the A0h slave address, with the same two level password scheme120 bytes protected by password 1 and 128 bytes protected by password 2Calibration and identification memory, with password protection on the DS1856 and a DS1852 compatible memory map
Supply and temperature2.85 V to 3.9 V, minus 40 C to plus 95 C2.85 V to 3.9 V, minus 40 C to plus 95 C2.85 V to 3.9 V, minus 40 C to plus 95 C3.3 V or 5 V supply, minus 40 C to plus 95 C
Package28-pin TQFN, 5 mm by 5 mm (DS1873 and DS1874)28-pin TQFN, 5 mm by 5 mm by 0.8 mm16-pin TSSOPSee the datasheet revision for the selected order code

Included Models and Order Codes

The models below are grouped in one product so a module bill of materials can be covered in a single enquiry. Send the full order code, the quantity and the module type, and we will confirm availability against that exact string.

ModelFunctionMonitor ChannelsControl OutputsInterfaceSupply
DS1874SFP and SFP+ controller with digital laser driver interface, complete SFF-8472 control and monitoringSix: temperature, VCC, MON1 to MON4Two 9-bit delta-sigma outputs with 36 entry temperature look up tablesTwo wire interface with a three wire master to the laser driver2.85 V to 3.9 V
DS1873SFP and SFP+ controller with analog laser driver interfaceSix: temperature, VCC, MON1 to MON4Four 10-bit delta-sigma outputs with 36 entry tables, plus two DACs with 72 entry and 36 entry tablesTwo wire compatible interface2.85 V to 3.9 V
DS1876Dual transmitter controller for video SFP modules, two laser drivers in one housingSix: temperature, VCC, PMON1, BMON1, PMON2, BMON2Four 10-bit delta-sigma outputs, each with a 72 entry temperature look up tableTwo wire interface, transmitter 1 at A2h and transmitter 2 at B2h2.85 V to 3.9 V
DS1863Burst mode PON controller with integrated monitoring for ONT transmittersFive: temperature, VCC, MON1 to MON3Two DAC outputs with temperature indexed look up tables and 0 dB, minus 3 dB or minus 6 dB levellingTwo wire compatible interface2.85 V to 3.9 V
DS1859Dual temperature controlled resistors with internally calibrated monitorsFive: temperature, VCC, MON1 to MON3Two 50 kohm or two 20 kohm linear nonvolatile variable resistors, 256 positions, updated every 2 degrees CTwo wire serial interface3.3 V or 5 V
DS1856Dual temperature controlled resistors with internally calibrated monitors and password protectionFive: temperature, VCC, MON1 to MON3Two 256 position linear nonvolatile variable resistors with a DS1852 compatible memory mapTwo wire serial interface3.3 V or 5 V

Key Features

SFF-8472 Control And Monitoring In One Part – The controllers cover the memory map, the calibration storage, the alarm and warning flags and the laser safety path, so the module firmware reads standard locations rather than a proprietary map.

Tracking Error Compensation – An APC loop holds the bias point while a temperature look up table corrects the tracking error of the laser, and modulation is corrected from its own temperature table, which keeps the extinction ratio in step over the operating range.

Laser Safety Without Extra Components – High output current, high bias current and low or high transmit power are monitored in hardware with maskable laser shutdown, and the DS1876 adds six quick trips for the fastest conditions.

Flexible Monitor Channels – Six analog channels on the SFP+ parts cover temperature, supply and four external inputs, with MON1 to MON4 calibrated internally or externally and MON3 differential with common mode referred to VCC where the monitor diode sits high.

Dual Transmitter Support – The DS1876 keeps two transmitters apart with separate addresses at A2h and B2h, which is what a video SFP module with two lasers needs inside a single housing.

Burst Mode Timing For Access Networks – The DS1863 meets BPON, GPON and GEPON burst timing and applies a calibrated power level, including 0 dB, minus 3 dB and minus 6 dB settings, without a separate calibration run.

Nonvolatile Temperature Compensation – The DS1859 and DS1856 set bias and control voltages with two 256 position variable resistors whose values are held in EEPROM and updated every 2 degrees C, which replaces a temperature compensation network built from discrete parts.

Protected Calibration Data – A two level password scheme gives three levels of access, with 120 bytes and 128 bytes of protected memory on the PON part and 256 additional bytes at the A0h address on the SFP+ parts, so the calibration written at module assembly cannot be overwritten in the field.

Applications

Module types where these controllers are used: A module bill of materials is normally quoted with the SUPERB PCB and SUPERB PCBA work we support, so the controller, the laser driver, the monitoring parts and the assembly come from one source.

SFP And SFP+ Transceiver Modules – Telecom and datacom modules that must report diagnostics and pass the host alarm handling, including single transmitter designs where the controller also drives the laser bias and modulation.

Video SFP Modules – Dual transmitter housings with two lasers, where the controller has to keep the two transmitters separate on the two wire bus.

PON ONT And OLT Transmitters – GPON, GEPON and BPON line rates where the transmitter bursts and the network expects a calibrated power level from the first burst.

Long Life Industrial And Defence Modules – Platforms that stay in production after the controller family has been marked last time buy, where a traceable source and a confirmed revision matter more than a new design.

Obsolete and Hard-to-Find Supply

These controllers were designed by Maxim and are now handled by Analog Devices, and several parts in the family carry a last time buy or not recommended for new designs status. That status changes the sourcing question from price to survival: the module has to keep building, the firmware expects a particular memory map, and the calibration data has to survive the change.

Because of that we check the exact revision before proposing a substitute, and we tell you where the differences sit. The DS1874 drives a laser driver over a three wire master while the DS1873 uses an analog interface, the DS1876 is a different part from the single transmitter controllers and cannot stand in for one, and the DS1856 keeps a DS1852 compatible memory map that the DS1859 does not. Where the exact part is still available we quote it with the date code and the packaging, and where it is not we quote the closest member of the family and state what the firmware has to change. Controllers are also normally quoted with the module parts around them, so the laser driver, the limiting amplifier and the monitoring parts can arrive as one kit.

For volume module builds, SUPERB Assembly support covers the SMT assembly of the module board.

Q: A controller in this family is marked last time buy. Can you still supply it?

A: Yes. Send the exact order code and the quantity and the SUPERB Tech sales team will confirm what is available, the date code and the closest equivalent where the original is no longer produced.

Why Source Diagnostics Controllers from Superb Automation?

  1. Optical Module Sourcing Focus: The module chain from laser driver to controller to monitoring part, quoted as one kit rather than as unrelated catalogue lines.
  2. Last Time Buy Handling: Where a part is at the end of its life we say so on the quote, and we can quote the quantity that covers a remaining production run.
  3. Revision Level Detail: Interface type, memory map and password scheme are checked before a substitute is proposed, because those are the details that break firmware.
  4. Stock, Samples And Build Quantities: Single pieces for a repair and full production quantities are both welcome, with batch information stated per line.
  5. Cross Reference Support: Family alternatives are listed with the differences written out, so your engineer can decide rather than discover the difference in the test rack.
  6. Documents With The Quote: Date code, packaging, condition and marking are confirmed before the order is placed.

Related Product Families

This page is part of the component range we supply for industrial, telecom, medical and defence builds. Continue with: Analog and Mixed-Signal ICs, ADI Laser Driver Chips for Optical Modules, Optical Power Monitor and Logarithmic Amplifier Chips, Optical Module Controller MCUs.